MagicardメーカーPrima 3 XID570ieの使用説明書/サービス説明書
ページ先へ移動 of 82
Reverse transfe r ID car d printer Printer Dr iver Manual Prima 3 PROFESSIONAL SERIES Secure ID car d printers.
Welcome to the high performance printer driver for the Prima 3 series printer. This manual will help you to install, set-up and configure the driver to get the best results for your prints.
Table of contents 1. Legal and Copyright Information ................................................................................................ .........6 2. Installa tion .........................................................................
6.3. Applicatio n Setup .............................................................................................................. ..............66 6.4. Multi-printe r enco ding......................................................................
1. Legal and Copyright Information This product is provided on an "as is" basis, without any other warranties, or condition s, expressed or implied, including but not limited to warranties of merchantable quality, merchantability or fitness for a particular purpose, or those arising by law, statute, usage of trade or course of dealing.
2. Inst allatio n Cont. 2.1. Printer Driver Installation Note 1: It is recommended to install the driver before you connect the printer to the PC! Note 2: System administrator privileges ar e required for driver installation! Log on to Windows as system administrator.
Note: Please note that you have to choose the exact name of the delivered member of our XID Printer Family. The wrong choice will result in a non-working printer!!! An administrator password can be set during initial installation. This password grants access to the Administration Center.
Note: It is recommended to use the proposed default path. Please verify the path shown and click " Next ". Click " Install " to continue.
Click " Continue Anyway " to continue the installation. Click " Continue Anyway " to continue the installation. Now the files will be installed.
Click on " Finish " to complete the installation.A reboot may be necessary, as shown below. Please wait until the driver installatio n is completed, then click " Finish ".
By calling the printer properties, from the " General " tab, you can print a test page as follows: After your test page has been printed successfully, click " OK ". After the installation has been completed, connect the printer to the PC and power on.
The Wizard will ask you to connect to Windows Update: Choose " No, not this time " and click " Next ". Choose " Install the software automatically " and click " Next ". Note: The hardware name ( "XID 5xxie U2") may differ depending on the firmware and the ID of the printer.
The Hardware wizard will install the needed files automatically. Click " Finish " to close the Hardware Wizard. Congratulations! You have successfully finished the printer driver installation.
2.2. Advanced Printer Configuration If the printer is used in a network environment and will be shared with other users, th en click " Shared as: " and name the printer. Afterwards other users can select this printer w ithin the network environment.
The Color Management settings should only be used by experienced users. Prima 3 Driver Manual 15.
Note: The screenshot may differ depending on system configuration: On the " About " tab you will find the version of the installed printer driver: Prima 3 Driver Manual 16.
3. Printing Preferences 3.1. Introduction into driver and print technology In graphic user interfaces all options are shown dy namically as there are card feeding, loading card in magazine, card leaving the printer etc.
3.2. Layout / Setup 3.2.1. Page Orientation This option will be used to setup the page orientation between Portrait and Landscap e. 3.2.2. Set-up for Control of Printing / Encoding This option sets up the control of " Print and Encode ", " Encode only " or " No Encoding ".
Set-up for use of cards with magnetic stripe or smartchip (Card Type) If the "Magstripe" or "Smartchip" checkbox is enabled, all options regarding encoding and positioning of card will be enabled. In addition, t he "Card placement in the printer tray" shows dynamically the correct images to the operator.
Flip Axis: Here you can setup the orientation of the 'card body', which is the same as the function as former 'Image Orientation'. The advantage is that you do not need to imagine how the card will rotate. Just pick up a card and you will understand the idea behind flipping the card horizontally or vertically.
3.3.3. Selection of text objects to be printed on K-plane By enabling " Text ", you are able to specify if all text or only black text should be printed on the K-plane.
3.3.4. Selection of black & white images to print on K-plane By enabling " Black and White Images " you can specify if black or black & grey images should be printed on the K plane.
It is recommended to choose either black or an extreme color, which will not be used in the rest of the layout. Pure colors (like Magenta) will never appear in digital photos, so it is safe t o use them without introducing side-effects. By clicking "OK" the color will be shown on the button.
3.3.5.2. Definition of area s for printing on K-plane In combination with the special colors (see chapter 3.3.5), you can define inclusion ar eas: After clicking on the area button the following dialo.
To create a new area: Click and draw a rectangle area while pressing and holding down the CTRL -key on the keyboard. To edit an area: Select an area you want to move or resize by clicking on the area itself or choose it from the list. You can move the area pixel by pixel using the cursor -keys.
Preview of defined sample K-Panel areas Measurement changes The following sample shows a change of units e.g. from Pixel to Inch Prima 3 Driver Manual 26.
Tip: Keeping values after disabling gives you the flexibility to design the areas before you enable this setting. Prima 3 Driver Manual 27.
3.3.6. PO Panel Area Definition (Peel Off) This function is designed to define a reas which will be prevented from printing (e.g. signature fields). The YMCK-PO looks like shown: Yellow Magenta Cyan Carbon (K) Peel Off (PO) Note: A special ribbon type is required to use this option.
The peel off area is enabled by clicking the checkbox: Warning: Use of full PO area results in non-visible printout. In each case you need to define smaller areas (e.
3.3.6.1. Definition of areas Peel Off To create a new area: Click and draw a rectangle area while pressing and holding down the CTRL -key on the keyboard. To edit an area: Select an area you want to move or resize by clicking on the area itself or choose it from the list.
Preview of defined sample K-Panel areas Tip: Keeping values after disabling gives you the flexibility to design the areas before you enable this setting.
3.4. UV Panel 3.4.1. Introduction The new generation of EDIsecure XID580ie and XID590ie printers supports using of YMCK - UV (ultra violet) ribbon as high level security feature. This feature contains the option to print layout objects with a special patch on the ribbon onto the card, which is invisible under normal daylight environment.
3.4.2.1. Option 'Bitmap from file' This option allows to place static bitmap files on the UV plane. The bitmap must fullfil following conditions: 1. Graphic: Bitmap format 2. Size: 1036 x 664 Pixel with 300 dpi resolution 3. Color mode: 256 Grayscale For security reasons the bitmap can be stored locally as well on the network.
As in all the other area definitions, the content once created can be used if enabled or stored for future use if disabled: 3.4.2.3. Option 'UV from second page' If an application is capable to print multipage documents (e.
3.4.3. Security Area The corner position of the printer´s unique identifier can be defined here: Prima 3 Driver Manual 35.
3.5. Advanced 3.5.1. Global Print Offset and K Plane Offset Global Print Offset: Here you can shift the offset of the layout in horizontal and vertical direction by changing the values; this influences the complete layout. K-plane Offset: The changing of the values for K-plane only influences the offset of the K -plane.
3.5.3. Synchronization This is only required if the application controls the chip enco ding. When encoding and printing batch jobs without the built-in Advanced Chip Encoding Framework , the option " Wait for card exit " must be checked: 3.5.
3.5.5. Card Output By enabling the " Card Output " option, the user can force or override the default setting of the printer driver. Independent from speed or material usage settings, the Card Output options " Front up " or " Front down " will force the card orientation when leaving the printer.
3.5.7. Sample of magnetic stripe Encoding Sending Track Information Magnetic track data is sent in the form of text strings from the application software to the printer driver, along with all of the other printable objects within your card design.
4. Advanced Intelligent Printer Management (AIPM) 4.1. Introduction The "Advanced Intelligent Printer Management" wa s developed with a focus on giving the most power and flexibility to the user. All necessary controls and settings are stored centrally in the Dispatcher (DISP) application.
4.2.1. Printers The printer line shows the printer’s status: If the printer is connected and detected by the Dispatcher and has no low level errors (e.
During the run time of DISP the card counter shows the Cards for print and Cards printed . Cards for print shows all jobs in the file list including copy prints. In special cases, e.g. if a cleaning pr ocedure is needed, an info line at the bottom shows the related info message.
Inside the Print Jobs list, the user can handle single jobs by r ight clicking with the mouse button as follows: - Delete (e.g. if unwanted after error recovery) - Suspense (e.
5. Administration Center The " Administration Center " is the central point for administrative management of hardware related settings, printer driver and LUT/passwor d control.
5.1.1. Re-transfer settings Ribbon Type Counts per roll (1000, 750) Temperature -3 (Low) ..Standard + 2 (High) Speed (Front/Back) -10 (Slow) .. Standard .. +2 (Fast) 5.1.2. Bend remedy Temperature Off .. -5 (Low) .. Standard .. 0 (High) Speed -2 (Slow) .
5.1.5. Print setting transfers Load from File An already set file can be loaded Save to File Actual settings can be saved to file From Printer Settings will be read from printer’s memory To Printer .
5.2. Options With the "Options" it is possible to enable / disable following items: 5.2.1. General Options Start DISP with printers in paused mode If enabled, the next time DISP is started (either by closing or rebooting PC) the printer will stay in paused mode.
5.2.2. Printer Driver Profiles a nd Printer Grouping Definition The Printer Group Definition is a unique technique powered by Digital Identification Solutions to define several groups of "virtual" printers.
5.2.2.1. Creati on of Printer Groups After clicking on " Add " in Printer Driver Profiles and Printer Grouping , the user needs to enter a new group name and the ID of the printer which will belong to this group. In the following window, the user can enter the following settings.
The following two samples show how to enter the information: Sample A: As a result of this definition the printer appears in the list. 1. 3. 2. 4. Prima 3 Driver Manual 50.
Sample B: When checking the maximum number of available pr inters you will get the maximum performance: It is possible to add several groups including overlapping IDs, as shown in the sample two groups named: - " PrinterXID #2 to #4 " with the IDs 2, 3 and 4 was added.
5.2.2.2. Deleti ng of Printer Groups There are two different ways of deleting Printer Groups: by Dispatcher or by use of the standard procedure in the Windows printer folder. We strongly recommend using Dispatcher. To delete Printer Groups the following steps have to be done: 1.
By clicking on the " Printing Preferences ... " button the user can view and setup the printer settings out of the Dispatcher for the highlighted printer name as shown below: 5.2.3.2. Exporting of Pr inter Driver Profiles By clicking on the " Export .
5.2.3.3. Importing of Printer Driver Profiles If the customer needs to import the printer profiles he can do this by clicking on the 'Import ...' button.
5.3. LUT / Password 5.3.1. Lookup Table Configuration Inside the Lookup Table Configuration the user has the possibility of using his own LUT tables. LUT tables contain the color control values, which can be used instead of the intern al printer LUT. The Lookup Table contains the values to control the print density for every color separately.
5.4. Driver Config This page allows setting, changing and removing the password of the Administration Center. When you click on " Reset " button, the following dialog appears. If a password has been set during installation, it can be changed here.
6. Advanced Chip Encoding Framework (ACEF) Included in the printer driver is the Advanced Chip Encoding Framework , which is capable of handling all card encoding itself. The mechanism is independent from the application, allowing virtually any Windows based applicati on to perform chip encoding.
6.1. Plugin architecture As the printer driver does not do the encoding itself but loads an additional piece of software that know how to "talk" with a certain encoder hardware and chip card, it is not limited to chips and encoders that are currently present on the market.
6.2. Software and Hardware Setup 6.2.1. Plugin Info When a plugin is installed properly and appears in the list of Installed Plugins , clicking on it will select and activate it.
This prevents plugins from crashing the driver by attempting to use unsupported functions of a later driver release. Plugin version The plugin's version number is shown here. This is for support purposes to determine which version of the plugin is installed on the system.
This mechanism allows easy recognition of the port name of each single encoder device in a multiple printer (and encoder) environment by plugging them in one-by-one.
6.2.3. Format Templates Some applications require different encodings, depending on the layout of the card, b ut use one chip type. Plugins can be developed to support multiple encoding styles, definitions, formats, and all in combination.
Each layout must then contain a "reference" to each format template, along with the encoding data, and the plugin would be able to understand what, where and how needs to be encoded. For an example how this reference looks like, please refer to section 6.
6.2.4. Configuration (Global Settings and Test) The most important part in the chip encoding setup is to test the communication with the encoding device and to test if the encoder can access, write to and read from the chip. Some encoders require even global settings like authentication keys or the transfer spee d, which is common for COM ports.
6.3. Application Setup The chip encoding features of the driver are application independent, i.e. the applicat ion does not need to be set-up for the specific encoder hardware of the encoding plugins.
Special transformations for shading, blending, winding, squeezing, skewing, twisting, outlining and anything else do process the text "as graphic" and are therefore not suggested for the encoding string. The font, however, is not relevant for parsing, as long as if it is a standard Windows fo nt.
6.5. Printing and enc oding over network Multiple workstations on the network can print on a PC that has one or more printers attached locally and has shared the printers in Windows. Such a PC is called print server . On the print server, it is mandatory that a user is logged on, otherwise the dispatcher will not be able to process the jobs.
6.7. Precoding Introduction A special preprocessing might be required by the application before encoding or printing the card , or both. In some cases, a serial number from a card needs to be processed and the card which has to be produced is selected by this serial number, i.
6.8. Encoding String In an encoding environment, there are many parameter s that must be configured in order to the encoding to be performed correctly.
corresponding section of the application's handbook on how to set up a text field with a string that can hold both, fixed and variable data. There are three types of applications that: - recogniz.
The following keywords in an encoding string are reserved by the driver and processed in a special way. Keyword Option Format Description pi mandatory Text p lug i n name This name must match with the one shown in the Installed Plugins list in Plugin Manager.
6.8.1. Encoding string examples 1. Simple encoding string {pi="Contact" ft="Guest" ...encoding data... } Uses the plugin " Contact " and the format template " Guest " to encode the encoding data, then prints the card.
4. Visual appearance of encoding strings This example shows how an encoding string does appear in the application window and does no t appear on the printed card Encoding string in the layout Printed .
7. T roubleshooting and known limit ations Print Errors As a result of the enhanced error recovery capability of the AIPM driver, the user can decide in case of an error to cancel, delete, recover, pause or re-print jobs.
2 3 4 8. Appendix A Layout placement on card The printer driver uses a technology that allows you to quickly setup and adjust the document properties for correct layout placement on the printed card. This section describes the idea behind it and how to find the correct settings in six int uitive steps.
Step 1: One- or two-sided layout Check if the design is a one or two-sided layout, i.e. if the layout has only a front side or a front and back side. One sided layout: Select + = Front side of card Ba.
Step 2: Landscape or portrait Check if the design is a landscape or a portrait design. Landscape Select = or Portrait Select = Prima 3 Driver Manual 77.
Step 3: Visible encoding features, Magnetic Stripe or Contact Chip If the card is not blank, it is important to select the features so the driver knows in which order an d the sides must be printed.
Step 4: Flip axis The driver determines the rotation of the layout sides fr om the flip axis of the card, which is the axis around which the card can be flipped and the layout stays in the correct orientation, not upside- down. The following illustration shows a vertical flip axis, i.
Step 5: Rotation of the card For non-blank cards, the layout design must cope with either the conta ct chip or the magnetic stripe or both on each side of the card. In the layout, these areas are usually left blan k and the Rotation-button allows the print to match the layout, i.
Step 6: Exchange the card sides As seen in the last step, for non-blank cards, the position of the magnetic stripe or contact chip or both must be adjusted to fit the layout.
Ultra Electronics Car d Systems North American Sales & Support Center 6711 - 176th Avenue NE Redmond W A 98052 T oll Fr ee: 877 236 0933 T el: (425) 556 9708 Fax: (425) 556 3962 email: USsales@ultramagicard.
デバイスMagicard Prima 3 XID570ieの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Magicard Prima 3 XID570ieをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMagicard Prima 3 XID570ieの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Magicard Prima 3 XID570ieの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Magicard Prima 3 XID570ieで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Magicard Prima 3 XID570ieを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMagicard Prima 3 XID570ieの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Magicard Prima 3 XID570ieに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMagicard Prima 3 XID570ieデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
