MaretronメーカーGPS200の使用説明書/サービス説明書
ページ先へ移動 of 23
® ® Revision 1.2 Page i GPS200 GPS Antenna/Receiver User’s Manual Revision 1.2 Copyright © 2012 Maretron, LLP All Rights Reserved Maretron, LLP 9014 N.
GPS200 User’s Manual Page ii Revision 1.2 Revision History Revision Description 1.0 Initial Revision 1.1 Corrected address in Section 7 1.2 Added prohibition of red Loctite th readlocking compound a.
® ® Revision 1.2 Page iii Table of Contents 1 Introduc tion .................................................................................................................. ..... 1 1.1 Firmware Revi sion ...............................
GPS200 User’s Manual Page iv Revision 1.2 This page intentionally left blank..
® ® Revision 1.2 Page 1 1 Introduction Congratulations on your purchase of the Ma retron GPS200 GPS Antenna/Receiver. Maretron has designed and built yo ur GPS200 to the highest sta ndards for years of reliable, dependable, and accurate service. The Maretron GPS200 is designed to operate wit hin the harsh demands of the marine environment.
GPS200 User’s Manual 1. Level with the earth’s horizontal plane – This gives the GPS200 antenna the optimal view of satellites from all directions.
® ® Figure 1 – Mounting the G PS200 to a flat surface 2.3.2 Mounting the GPS200 to a Standard Marine Pole Mount Screw the included GPS200 antenna mount base to the standard marine mount.
GPS200 User’s Manual Page 4 Revision 1.2 interface through a connector that can be found on the bottom of the device (see Figure 3 ). e cable. Please follow recommended practices for installing NMEA 2000 ® network products.
® ® Figure 4 – NMEA 2000 ® Connector Face Views 2.4.1 Checking Connections Once the NMEA 2000 ® connection to the Maretron GPS200 has been completed, check to see that GPS information is being properly transmitt ed by observing an appropr iate display.
GPS200 User’s Manual Page 6 Revision 1.2 These parameters may be confi gured using a Maretron display (DSM250), or the parameters can be configured using a Maretron NMEA 2000 ® /USB gateway (USB100) and Maretron’s N2KAnalyzer software.
® ® Revision 1.2 Page 7 • Clean the unit with a soft cloth. Do not use chemical cleaners as they may remove paint or markings or may corrode the GPS200 enclosure or seals. Do not use any cleaners containing acetone, as they will deteriorate the plastic enclosure.
GPS200 User’s Manual Page 8 Revision 1.2 5 Troubleshooting If you notice unexpected operatio n of the Maretron GPS200, follow the troubleshooting procedures in this section to remedy simple problems.
® ® Revision 1.2 Page 9 6 Technical Specifications Specifications Parameter Value Comment Position Accuracy (Autonomous) <3m 2D RMS (95% of Data Falls Within 10m ) Position Accuracy (WAAS) <2.
GPS200 User’s Manual Page 10 Revision 1.2 Electrical Parameter Value Comment Operating Voltage 9 to 16 Volts DC Voltage Power Consumption <100mA Average Current Drai n Load Equivalence Number (LEN) 2 NMEA 2000 ® Spec.
® ® 8 Installation Template Please check the dimensions before using the fo llowing diagram as a template for drilling the mounting holes; the printing process may have distorted the dimensions. 2.11” Figure 5 – Horizontal Mounting Surface Template Revision 1.
GPS200 User’s Manual Page 12 Revision 1.2 9 Maretron (2 Year) Limited Warranty Maretron warrants the GPS200 to be free from defects in materia ls and workmanship for t wo (2) years from the date of original purchase.
® ® Revision 1.2 Appendix A – NMEA 2000 ® Interfacing Page A1 Appendix A – NMEA 2000 ® Interfacing GPS200 NMEA 2000 ® Periodic Data Transmitted PGNs PGN 126992 – System Time The GPS200 uses this PGN to provide a regular transmission of UTC time and date and to provide synchronism for measur ement data.
GPS200 User’s Manual Page A2 Appendix A – NMEA 2000 ® Interfacing Revision 1.2 The GPS200 uses this PGN to provide lati tude and longitude referenced to WGS84.
® ® Revision 1.2 Appendix A – NMEA 2000 ® Interfacing Page A3 4: Latitude – Latitude in 1x10 -16 degrees ("-" = south, “+” = north) 5: Longitude – Longitude in 1x10 -16 degrees .
GPS200 User’s Manual Page A4 Appendix A – NMEA 2000 ® Interfacing Revision 1.2 4: Reserved (2 bits) – This field is rese rved by NMEA; therefore, this field always contains a value of 0x3 (the .
® ® Revision 1.2 Appendix A – NMEA 2000 ® Interfacing Page A5 GPS200 NMEA 2000 ® Non-Periodic Data Transmitted PGNs PGN 129538 – GNSS Control Status The GPS200 uses this PGN to provide the GN SS com mon satellite receiv er parameter status. GPS200 sends this PGN only when r equested by PGN 059904 (ISO Request).
GPS200 User’s Manual Page A6 Appendix A – NMEA 2000 ® Interfacing Revision 1.2 This will change the confi guration of the GPS200. Field 1: Complex Command Group Function Code (8 bits) – set this field’s value to 0x01, which denotes a command PGN.
® ® Revision 1.2 Appendix A – NMEA 2000 ® Interfacing Page A7 11: Software Code (16 bits) – set this field’s value to 0x0001, which is the identifier for this version of the Mare tron proprie.
デバイスMaretron GPS200の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Maretron GPS200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMaretron GPS200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Maretron GPS200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Maretron GPS200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Maretron GPS200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMaretron GPS200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Maretron GPS200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMaretron GPS200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。