AbocomメーカーCWB1000の使用説明書/サービス説明書
ページ先へ移動 of 19
IEEE802.11b 11Mbps CompactFlash Card Quick Installation Guide M73-APO01-560.
REGULATORY STATEMENTS FCC Certification The United States Federal Communication Commission (FCC) and the Canadian Department of Communications have established certain rules governing the use of electronic equipment. Part15, Class B This device complies with Part 15 o f FCC rules.
SOFTWARE INSTALLATION FOR WINDOWS CE3.0 Connect your PDA to your PC. Make sure you have the Microsoft ActiveSyn c Utility installed on your PC to make an active connection. Caution : DO NOT insert the Wireless CompactFlash Card into the PDA BEFORE installing the co nfiguration utility.
- 3 - 4. Clic k Next to contin ue. 5. Clic k OK . 6. Clic k Finish ..
- 4 - 7. You can now i nsert the Wi reless CompactFlash Card into the PDA. Then use the Se ttings on your Windows CE to configure the network settings.
HARDWARE INSTALLATION For PDA Insert the Wireless CF card into the Windows CE-based PDA by aligni ng the Wireless CF card toward the CF slot. For Notebook PC Note : This section is only for users who had CF to PCMCIA Adapter. Pleas e refer to the manual for more details.
NETWORK CONNECTION FOR WINDOWS CE3.0 Once the driver has been installed, you must make some changes to your network settin gs. 1. Go to Start Æ Settings Æ Connections . Click on Network Adapters . 2. Highlight PRISM 11Mbps Wireless LAN Adapter , click Properties .
- 7 - 3. ~ Use server-assigned IP address If your network suppor ts DHCP, select Use server-assigned IP address . The IP address and other information will be automatically assigned. T hen click ok . ~ Use server-assigned IP address If your ne twork does not support DHCP, select Use specific IP address .
- 8 - 4. A message as below may appear saying you must remove and re -insert the Wireless CompactFlash Card to have the change s take affect. Click OK .
CONFIGURATION UTILITY FOR WINDOWS CE3.0 After installing the Wireless Com pactFlash Card’s driver successf ully, go to Start Æ Programs . Click on PRISM Sett ings , the Network Status icon will appear in the task bar. Network Status Icon & Icon Menu The Status Icon Icon Link Status Green indicates a strong link.
- 10 - Icon Menu After clicking on the icon, the icon menu as displayed below will prompt you to configure the Wireless CompactFlash Card. Items Description Wireless Radio On Wireless Radio Off These two items al lows you to enable or disable the wireless radio.
- 11 - All settings are categorized into 5 tab s: Link Configuration Encryption Site Survey About Link The Link tab provides you the statu s of the Wireless CompactFlash Card. Item Description State It displays the connection state of the Wireless CompactF lash Card with the wireless network.
Item Description Current Channel It displays the s elected chan nel that is currently used. (There are 14 channels available, depends on the country.) Enable Radio / Disable Radio Click this button to enabl e/disable the wireless radio. The Wireless CompactFlash Card will connect/disconnect with the wireless network.
- 13 - Item Description Profile Name Saves values for all previous setting parameters. The default values contain the parameters configured at installation. Once the demands for switching between different networking environments are requ ired, you can also set the additional profiles to eliminate the co nfiguration time.
Item Description Network Type It displays the type of BSS. Access Point: allows the Adapter to communicate with a wired network which employing an A ccess Point. Peer-to-Peer: allows PC-to-PC, station-to-station communication without employing an Access Po int.
- 15 - Item Description Encryption (WEP) WEP is a data privac y mechanis m based on a 64-bit/128-bit shared key algorithm. Under the drop-down box, you can choose to have WEP encryption Disabled , 64 bit , or 128 bit . Create Keys with Passphrase A Passphrase can be entered t o generate four keys used for WEP.
- 16 - Key 1: Key 2: Key 3: Key 4: This setting is the configur ation key used in accessing the wireless network via WEP encryption. Use WEP Key The default key field can be used for specifying which of the fo ur encryption ke ys to transmit data on the wireless network.
- 17 - Site Survey The Site Survey tab shows all the available Access Points or Peer-t o-Peer types and their features. Item Description Network Name The name must be identical fo r all devices and points attemptin g to connect to the same network. BSSID A set of wireless stations is r eferred to as a Basic Service Set (BSS).
Item Description WEP Encryption It displays the status of WEP Encryption. Signal Level It displays the signal strength of the connection between the Wireless CompactFlash Card and the Access Point it connects. Rescan Search for all available n etworks.
デバイスAbocom CWB1000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Abocom CWB1000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAbocom CWB1000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Abocom CWB1000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Abocom CWB1000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Abocom CWB1000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAbocom CWB1000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Abocom CWB1000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAbocom CWB1000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。