MaytagメーカーW10267633Aの使用説明書/サービス説明書
ページ先へ移動 of 16
ELECTRIC DRYER INSTALLATION INSTRUCTIONS U.S.A. ONLY Para una version de esta s instruccione s en españo l, visite www .Whirlpool.com T ABLE OF CONTENTS TABLE OF CONTENTS .................................. ................................ 1 DRYER SAFETY.
2 INST ALLA TION REQUIREMENTS T ools and Parts G ather the r equired tools and parts be fore starting installation. Read and follow the instructions provid ed with any tools listed here.
3 Location Requirements Y ou will need ■ A location that allows proper exhaust installation. See “V enting Requirements.” ■ A separate 30-amp circuit. ■ If using a power supply cord, a grounded electrical outlet within 2 ft (6 10 mm) of either side of dryer .
4 ELECTRIC DR YER POWER HOOKUP Electrical Requirements It is your r esponsi b ility ■ T o contact a qualified electrical installer . ■ T o be sure that the electrical connection is adequate and in conformance with the National E lectrical Code, ANSI/NFP A 70- latest edition and all loca l codes and ordinances.
5 Electrical Connection W ARNIN G Fire Hazar d Use a new UL listed 30 amp power supply cord. Use a UL listed strain relief. Disconnect power b efore making electrical connections. Connect neutral wire (white or center wir e) to center terminal (silver).
6 block opening, screw r emova ble conduit connec tor onto strain relief threads. B C A A. Removable conduit connector B. Hole below terminal block opening C. Strain relief threads ■ Put direct wire cable thr ough strain relief. Strain r elief should have a tight fit with drye r cabinet and be in a horizontal position.
7 3. Connect ground wir e (green or bar e) of power supp ly cord to external ground conductor scr ew . Tighten screw . A. External ground conductor screw B. Neutral ground wire C. Ground wire (green or bare) of power supply cord D. 3/4" (19 mm) UL listed str ain relief E.
8 4. Place the hooked ends of the othe r direct wire cable wir es under the outer termin al block screws (hooks facing right). Squeeze hooked ends together . Tighten screws. 5. Tighten strain relief scr ew . 6. Insert tab of terminal block cover into slot of dryer rear panel.
9 2. Place the hooked end of the neutral wire (white or center wir e) of direct wir e cable under the cente r screw of terminal block (hook facing right). Squeeze hooked end together . Tighten screw . A C D E B D. Neutral wire (white or center wire) E.
10 VE N T I N G V enting Requirements W ARNIN G Fire Hazar d Use a heavy metal vent. Do not use a plastic vent. Do not use a metal foil vent. Failure to follow these instructions can result in death or re. WARNING: T o reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.
Improper ventin g can cause moistur e an d lint to collect in d oors, which may result in: Moi s ture damage to woodwork, furniture, paint, wallpaper, carpet s , etc.
12 Determine vent path ■ Select the route that will provide the straightest a nd most direct path outdoors. ■ Plan the in stallation t o use th e fewest number of elbows and turns. ■ When using elbows or m aking tur ns, allow as much r oom as possible.
13 4. Using pliers, tighten the coupling s with an additional two-thirds turn . NOTE: Do not overtighten. Damage to the coupling can result. 5. Attach “Y” connector to brass male end of small hose. Screw on coupling by hand until it is seated on connector .
14 All Models: 13. Select a Timed Dry heated cycle, an d start the dryer . Do not select the Air Only T emperatur e setting. If the dryer will not start, check the following: ■ Controls are set in a running or “On” position. ■ Start butt on has be en pushed firmly .
15 3. Remove the 4 screws from the opposite side of the door . 4. Install the 2 hinges to the front panel of the dryer using 4 screws. Use the non-slotted side to attach the hinge to the fr ont panel. 5. Instal l screws in top hinge holes in the door .
Press any key to clear the code from the display and return to the estimated ti me r emaining. T ry th e following: Check to see if a household fuse has blown or circuit breaker has tripped. Electric dryers use two household fuses or breakers. Replace the fuse or reset the circuit br eaker .
デバイスMaytag W10267633Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Maytag W10267633Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMaytag W10267633Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Maytag W10267633Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Maytag W10267633Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Maytag W10267633Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMaytag W10267633Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Maytag W10267633Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMaytag W10267633Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。