Mercedes-Benzメーカー2010 R350 BlueTECの使用説明書/サービス説明書
ページ先へ移動 of 364
R-Class Operator’s Manual 251_AKB; 4; 52, en-US d2ureepe, Version: 2.11.8.1 2009-03-23T09:22:52+01:00 - Seite 1.
Symbols Trademarks ® : R AdBlue ® is a registered trademark of the German Association of the Automotive Industry (VDA). R BabySmart TM is a trademark of Siemens Automotive Corp. R Bluetooth ® is a registered trademark of Bluetooth SIG Inc. R ESP ® and PRE-SAFE ® are registered trademarks of Daimler.
Our company and staff congratulate you on the purchase of your new Mercedes-Benz. Your selection of our product is a demonstration of your trust in our company name. Furthermore, it exemplifies your desire to own an automobile that will be as easy as possible to operate and will provide years of service.
251_AKB; 4; 52, en-US d2ureepe, Version: 2.11.8.1 2009-03-23T09:22:52+01:00 - Seite 2.
Index ....................................................... 4 Introduction ......................................... 20 At a glance ........................................... 25 Safety and security ............................. 35 Controls in detail .
1, 2, 3 ... 115V AC Socket ................................. 206 3-zone automatic climate control see Climate control system 4-ETS (Electronic Traction System) ... 65 4MATIC see All-wheel drive (4MATIC) A ABS (Antilock Brake System) ............. 63 Indicator lamp .
Armrest, rear Storage compartment .................... 199 Ashtrays ............................................. 204 Aspect ratio (tires) ............................ 249 Audio/DVD menu .............................. 128 Auto-dimming rear view mirrors .
Cargo net ........................................... 196 Cargo tie-down rings ......................... 188 Carpets, cleaning .............................. 267 Central locking Automatic ................................ 74, 137 KEYLESS-GO ...........
Changing the set speed ................. 144 Last stored speed .......................... 144 Lever .............................................. 143 Messages in the mutlifunction display ........................................... 280 Resume function .
Driving off .................................. 112, 255 Driving safety systems ....................... 63 4-ETS ............................................... 65 ABS .................................................. 63 BAS ..........................
Parking position ............................... 95 Power folding ................................... 95 Exterior view of vehicle ...................... 26 F Fastening the seat belts ..................... 49 First aid kit .............................
Gross Vehicle Weight see GVW Gross Vehicle Weight Rating see GVW R GTW (Gross Trailer Weight) .............. 249 GVW (Gross Vehicle Weight) ............ 249 GVWR (Gross Vehicle Weight Rating) ................................................ 249 H Halogen headlamps see Headlamps Hard plastic trim items, cleaning .
J Jack ..................................................... 272 Jump starting ..................................... 336 K Key, Mechanical Loss of ............................................. 73 Unlocking/locking manually .......... 308 Key, SmartKey Battery check lamp .
Loading see Vehicle loading Locator lighting ................................. 135 Lock button Outside door handle (KEYLESS- GO) .................................................. 73 Locking the vehicle KEYLESS-GO .................................... 71 Manually .
SmartKey with KEYLESS-GO .......... 289 SRS ................................................ 287 Tailgate .......................................... 288 Tail lamps ...................................... 297 Tele Aid ...................................
Parktronic system Cleaning system sensors ............... 265 Malfunction .................................... 159 Minimum distance ......................... 158 Sensor range ................................. 157 Switching on/off .....................
Reminder, Seat belt see Seat belts, Telltale Remote control see Key, SmartKey Remote door unlock (Tele Aid) ......... 212 Replacing bulbs ................................. 312 Reporting safety defects .................... 23 Research Octane Number see RON Reserve fuel Messages in the multifunction display .
Snow chains ...................................... 252 Snow tires see Winter tires Spare wheel ....................................... 347 Mounting ....................................... 324 Storage location ............................ 272 Speedometer .
Telephone ............................................. 30 Answering/ending a call ................ 141 Hands-free microphone ................... 33 Menu ............................................. 140 Operation .....................................
Decoupling ..................................... 259 Electrical connections .................... 256 Towing ........................................... 258 Trailer hitch ................................... 256 Weights and ratings .....................
Parking brake ................................ 286 Parktronic system .......................... 159 Seat belt telltale ............................ 302 Warranty coverage ............................ 344 Washer and headlamp cleaning system ............
Product Information Please observe the following in your own best interest: We recommend using Genuine Mercedes- Benz Parts as well as conversion parts and accessories explicitly approved by us for your vehicle model. We have tested these parts to determine their reliability, safety and special suitability for Mercedes-Benz vehicles.
Rhode Island, and Vermont Emission Control System Warranty 1 R State Warranty Enforcement Laws (Lemon Laws) Important notice for California retail buyers and lessees of Mercedes-Benz automobiles Under.
determined by our authorized technician and tow service provider. For additional information refer to the Mercedes-Benz Roadside Assistance Program brochure (in the USA) or the Roadside Assistance section of the Service and Warranty Information Booklet (in Canada) in your vehicle literature portfolio.
Proper use of the vehicle Proper use of the vehicle requires that you are familiar with the following information and rules: R the safety precautions in this manual R the “Technical data” section .
This information helps, for example, to diagnose vehicle systems after a collision and to continuously improve vehicle safety. Daimler may access the information and share it with others R for safety .
Exterior view ....................................... 26 Cockpit ................................................. 27 Instrument cluster .............................. 28 Multifunction steering wheel ............. 30 Center console ...................
Exterior view i This Operator’s Manual describes all features, standard or optional, potentially available for your vehicle at the time of purchase. Please be aware that your vehicle might not be equipped with all features described in this manual.
Cockpit Function Page : Cruise control lever: Cruise control 142 Distronic 145 ; Instrument cluster 28, 122 = Multifunction steering wheel 30, 123 ? Horn A Steering wheel gearshift control 121 B Gear .
Instrument cluster Function Page : # Left turn signal indicator lamp ; To dim instrument cluster illumination 123 = Reset button for: Trip odometer 123 Settings 131 ? To brighten instrument cluster il.
Function Page D Multifunction display with: Trip odometer 125 Main odometer 125 E Tachometer with: 7 Seat belt telltale 51, 302 % Preglow indicator lamp, diesel engine only 111 + Supplemental Restrain.
Multifunction steering wheel Function Page : Multifunction display 125 ; Press button 6 : to answer a call 140 to dial 4 140 to redial 4 140 Press button ~ : to end a call 140 to reject an incoming ca.
Center console Upper part Function Page : COMAND system, see separate operating instructions ; Climate control system 162 Rear window defroster 180 = Seat heating, front passenger side 91 ? Seat venti.
Lower part Function Page : Storage compartment 198 ; Ashtray with storage compartment 204 Cigarette lighter 205 = Cup holder 201 ? Front armrest storage compartment/telephone tray 198 A Removable card.
Function Page H Hands-free microphone for Tele Aid (emergency call system), telephone, and Voice Control System, see separate operating instructions I Front left interior lamp 102 Door control panel F.
34 251_AKB; 4; 52, en-US d2ureepe, Version: 2.11.8.1 2009-03-23T09:22:52+01:00 - Seite 34.
Vehicle equipment .............................. 36 Occupant safety .................................. 36 Panic alarm .......................................... 62 Driving safety systems ....................... 63 Anti-theft systems ..................
Vehicle equipment i This Operator’s Manual describes all features, standard or optional, potentially available for your vehicle at the time of purchase. Please be aware that your vehicle might not be equipped with all features described in this manual.
G Warning! The SRS self-check has detected a malfunction when the SRS indicator lamp + : R does not come on at all R does not go out after 4 seconds after the engine was started R comes on while driving For your safety, we strongly recommend that you contact an authorized Mercedes-Benz Center immediately to have the system checked.
you have any difficulties, please contact an authorized Mercedes-Benz Center. R Do not lean your head or chest close to the steering wheel or dashboard. R Keep hands on the outside of the steering wheel rim. Placing hands and arms inside the rim can increase the risk and potential severity of hand/arm injury when the driver front air bag inflates.
bags repaired. This will help to make sure the air bags will continue to provide supplemental crash protection for occupants. Safety guidelines for the seat belt, Emergency Tensioning Device (ETD) and air bag G Warning! R Damaged seat belts or seat belts that have been subjected to stress in an accident must be replaced.
Front air bags G Observe Safety notes, see page 37. Driver’s front air bag : and front passenger front air bag ; are designed to provide increased protection for the driver and front passenger against the risk of injuries to the head and thorax.
impact air bags inoperative or causing unintended air bag deployment. Work on the doors must therefore only be performed by qualified technicians. Contact an authorized Mercedes-Benz Center. Front side impact air bags : and rear side impact air bags ; are designed to provide increased protection for the thorax but not the head, neck and arms.
R regardless of whether the seat belt on the impacted side of the vehicle is in use R in certain vehicle rollovers, if the system determines that air bag deployment can offer additional protection to that provided by the seat belt Window curtain air bags : are not deployed in impacts which do not exceed the system’s deployment threshold.
When the OCS senses that the front passenger seat occupant is classified as being heavier than the weight of a typical 12-month-old child seated in a standard child restraint or as being a small indiv.
completely eliminate this risk is to never place a child in a rear-facing child restraint in the front seat. We therefore strongly recommend that you always place a child in a rear-facing child restraint in a backseat.
In order to ensure proper operation of the air bag system and OCS: R Do not place more than 4.4 lb (2 kg) into the parcel net on the back of the front passenger seat. Otherwise, the OCS may not be able to properly approximate the occupant weight category.
The infant or child restraint must be properly secured with the vehicle’s seat belt, the seat belt and top tether strap, or lower anchors and top tether strap, fully in accordance with the child seat manufacturer’s instructions.
Special BabySmart™ compatible child seats, designed for use with the Mercedes-Benz system, are required for use with the BabySmart™ air bag deactivation system. Please contact an authorized Mercedes-Benz Center for information on availability. With the special child seat installed properly, the front passenger front air bag will not deploy.
For information on infants and children traveling with you in the vehicle and restraint systems for infants and children, see “Children in the vehicle” ( Y page 55). G Warning! Always fasten your seat belt before driving off. Always make sure all of your passengers are properly restrained.
thresholds and in certain rollovers (window curtain air bags and ETDs). R Never wear the shoulder belt under your arm, against your neck or off your shoulder. In a frontal crash, your body would move too far forward. That would increase the chance of head and neck injuries.
G Warning! Vehicles with BabySmart™ air bag deactivation system, Canada only: Children 12 years old and under must never ride in the front seat, except in a Mercedes-Benz authorized BabySmart™ com.
Seat belt adjustment function The seat belt adjustment function adjusts the seat belts on both front seats to the upper body of the respective vehicle occupant.
Emergency Tensioning Device (ETD), seat belt force limiter The seat belts for the following seats are equipped with ETDs and seat belt force limiters: R front seats R outboard second-row seats R third.
R If the vehicle is in a critical dynamic driving situation, the door windows close, except for a minimal gap that remains open. R Vehicles with power tilt/sliding sunroof: If the vehicle is in a critical dynamic driving situation, the tilt/sliding sunroof also closes, except for a minimal gap that remains open.
see “Head restraint fore and aft adjustment” ( Y page 83). Correct driver seat adjustment G Warning! In order to avoid possible loss of vehicle control the following must be done before the vehicl.
R Adjust the seat cushion so that the front edge of the seat cushion lightly supports your legs. R Adjust the head restraint so that it is as close to the head as possible and the center of the head restraint supports the back of the head at eye level.
During seat belt retraction, a ratcheting sound can be heard to indicate that the special seat belt retractor is activated. The seat belt is now locked. X Push down on child restraint to take up any slack. To deactivate the special seat belt retractor: X Release the seat belt buckle and let the seat belt retract completely.
activated. Always make sure the 42 indicator lamp is illuminated, indicating that the front passenger front air bag is deactivated. R Canada only: Children 12 years old and under must never ride in th.
Top tether straps enable an additional connection to be made between child restraint systems secured with LATCH-type anchors and rear seats. This can further reduce the risk of injury.
G Warning! After installing top tether straps, make sure the seats are locked properly, the seat backrests are in an upright position and they are locked properly. An outboard second-row seat is locked properly only when the lock status indicator is in hinged position and the red marking is barely visible.
X Fold seat backrest ; forward to seat cushion = as far as necessary for you to access anchorage ring ? . X Guide top tether strap B between head restraint and top of the seat backrest. X Securely fasten hook A , which is part of top tether strap B , to anchorage ring ? .
The LATCH-type anchors on the outboard second-row seats are covered with upholstery blends. Information sign ; indicates the position of anchor : . X Move the respective outboard second-row seat backrest to an upright position ( Y page 87). X Push the upholstery blend to the side.
X Securing: Press the lever down in direction of arrow ; . X Check to make sure the child safety locks are working properly. X Releasing: Press the lever up in direction of arrow : . Override switch G Observe Safety notes, see page 55. With the override switch you can disable the rear door window switches in the rear door panels.
i USA only: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation.
and significantly reduces braking effectiveness. The Antilock Brake System (ABS) regulates the brake pressure so that the wheels do not lock during braking. This allows you to maintain the ability to steer your vehicle. The ABS is functional above a speed of approximately 5 mph (8 km/h) independent of road surface conditions.
ESP ® G Observe Safety notes, see page 63. The Electronic Stability Program (ESP ® ) is operational as soon as the engine is running. It monitors the vehicle’s traction (force of adhesive friction between the tires and the road surface) and handling.
circumstances described below. Disabling the system will reduce vehicle stability in driving maneuvers. Do not switch off the ESP ® when a spare wheel is mounted.
The ESP ® will assist you in such situations. The ESP ® recognizes when the trailer starts swaying and will apply the brakes to reduce the vehicle speed to a non-critical speed that allows the vehicle-trailer combination to stabilize.
X Arming: Lock the vehicle with the SmartKey or with KEYLESS-GO. The turn signal lamps flash three times to indicate that the vehicle is locked. Indicator lamp : flashes to indicate that the alarm system is armed. i If the turn signal lamps do not flash three times, a door or the tailgate may not be properly closed.
Vehicle equipment .............................. 70 Locking and unlocking ....................... 70 Starter switch positions ..................... 79 Seats .................................................... 81 Multifunction steering wheel .........
Vehicle equipment i This Operator’s Manual describes all features, standard or optional, potentially available for your vehicle at the time of purchase. Please be aware that your vehicle might not be equipped with all features described in this manual.
i Canada only: This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. this device must accept any interference received, including interference that may cause undesired operation of the device.
Important notes on using KEYLESS-GO R You can also use the SmartKey with KEYLESS-GO like a normal SmartKey ( Y page 70). R You can combine KEYLESS-GO functions with normal SmartKey functions (e.g. unlocking with KEYLESS-GO and locking with button & ).
Unless you open a door or the tailgate within approximately 40 seconds after unlocking the vehicle: R The vehicle will be locked again. R The antitheft alarm system will be rearmed. X Global locking: Press lock button : on an outside door handle. Selective setting If you frequently travel alone, you may wish to reprogram the SmartKey.
Opening the doors from the inside You can open a door from the inside even when it is locked unless it is secured with the child safety lock ( Y page 61).
If the vehicle was previously locked with the central locking switch R and the SmartKey is set to factory settings, the complete vehicle is unlocked when a front door is opened from the inside R and t.
X Push handle : in direction of arrow ; and hold it there. X From this position, lift handle : in direction of arrow = and hold it there. The tailgate is released and can be opened manually. i If you do not open the tailgate within a few seconds, the tailgate lock will engage again automatically.
Closing the tailgate from the outside G Observe Safety notes, see page 55. G Warning! Monitor the closing procedure carefully to make sure no one is in danger of being injured. To prevent possible personal injury, always keep hands and fingers away from the cargo compartment opening when closing the tailgate.
have status 0 ): Press button F on the SmartKey. You can close the tailgate and lock the vehicle simultaneously from the outside using the KEYLESS-GO locking/closing switch. X Make sure you have the SmartKey with you. X Press KEYLESS-GO locking/closing switch : briefly.
the door-mounted remote tailgate switch. Monitor the closing procedure carefully to make sure no one is in danger of being injured. To interrupt the closing procedure, press or pull the door-mounted remote tailgate switch. If the tailgate comes into contact with an object while closing, the closing procedure is stopped and the tailgate reopens.
X Always remove the SmartKey from the starter switch when the engine is not in operation. This will help to prevent accelerated vehicle battery discharge or a completely discharged vehicle battery. If the SmartKey cannot be turned in the starter switch, the vehicle battery may not be sufficiently charged.
Position 1 X Press the KEYLESS-GO start/stop button once. This supplies power for some electrical consumers, such as radio functions. i If you now press the KEYLESS-GO start/ stop button R once more, .
R Adjust the head restraint so that it is as close to the head as possible. The center of the head restraint must support the back of the head at eye level. R Never place hands under the seat or near any moving parts while a seat is being adjusted. Failure to do so could result in an accident and/or serious personal injury.
X Seat fore and aft adjustment: Press the switch forward or backward in direction of arrow A . X Seat backrest tilt: Press the switch forward or backward in direction of arrow ? .
X While seated, reach behind you with both hands and find lower edge of the head restraint. X Push or pull on the lower edge of the head restraint cushion to the desired position. Easy-entry/exit feature for third-row seats This feature allows for easier access to and exit from the vehicle’s third-row seats.
X To exit the vehicle when seated on a third- row seat, pull up and hold easy-exit strap : . The second-row seat backrest folds forward. X Push second-row seat forward a far as it will go. Easy-entry/exit position X Exit the vehicle. For information on how to fold down the second-row seats completely, see “Expanding cargo volume” ( Y page 189).
Seat locked When the seat is locked, lock status indicator : is in hinged position and red marking ; is barely visible. Lumbar support You can adjust the contour of the driver’s seat lumbar support to help enhance support to your spine. X Curvature position: Use button : to move the curvature up and button = to move it down.
maneuvers, or in an accident. If you slide under it, the seat belt would apply force at the abdomen or neck. That could cause serious or even fatal injuries. Seat locked When the seat is locked, lock status indicator : is in hinged position and red marking ; is barely visible.
X While seated, pull adjustment handle : in direction of arrow and hold it there. X To move seat backrest back, lean lightly against backrest. X To move seat backrest forward, lean forward with adjustment handle : pulled. The seat backrest will move forward against your back.
Seat position for removal of head restraints from outboard second-row seats Removing X Pull head restraint : to its uppermost position. X Press release button ; and pull out head restraint : . Installing X Insert head restraint : into openings on the seat backrest.
X Pull seat backrest release strap : in direction of arrow. X Completely fold seat backrest ; forward so that it rests on seat cushion = (armrest position). Armrest position Multicontour seat The multicontour seat has a movable seat cushion and inflatable air cushions built into the seat backrest to provide additional lumbar and side support.
Seat heating Front seat heating switches The switches for the outboard second-row seat heating are located in the rear center console. Rear seat heating switches The red indicator lamps ; in front or rear seat heating switch : come on to show which heating level you have selected.
Steering wheel adjustment, manual X Unlocking: Pull release handle : out to its stop limit. X Move steering wheel to the desired position. X Locking: Push release handle : back to its original position. X Make sure the steering wheel is securely locked by trying to move it up and down as well as in and out before driving off.
i When the current position for the steering wheel is in the uppermost tilt position, the steering wheel will no longer be able to move upward when the easy-entry/exit feature is activated. The adjustment procedure is briefly interrupted when the engine is started.
Interior rear view mirror X Adjust the interior rear view mirror manually. Interior rear view mirror, antiglare position X Tilt the mirror to the antiglare position by moving lever : towards the windshield.
from headlamps falls on the sensor in the interior rear view mirror. The rear view mirrors will not react if the automatic transmission is set to reverse gear R or the interior lighting is switched on. G Warning! The auto-dimming function does not react if incoming light is not aimed directly at sensors in the interior rear view mirror.
Folding in and out automatically The function must be activated in the fold-in function for the exterior rear view mirrors of the Convenience submenu ( Y page 138). The exterior rear view mirrors fold in automatically as soon as the vehicle is locked from the outside.
Each memory position button on the driver’s side can store all of the following settings: R Seat position R Steering wheel position R Exterior rear view mirrors’ position G Warning! Do not activate the memory function while driving. Activating the memory function while driving could cause the driver to lose control of the vehicle.
5 T Parking lamps (also tail lamps, license plate lamps, side marker lamps and instrument panel lamps) 6 L Low-beam headlamps or high-beam headlamps 7 N Front fog lamps 8 R Rear fog lamp i The exterio.
The following lamps come on and go out depending on the brightness of the ambient light with the SmartKey in starter switch position 1 or the KEYLESS-GO start/stop button pressed once: R tail lamps R .
G Warning! In low ambient lighting or foggy conditions, only switch from position à to L with the vehicle at a standstill in a safe location. Switching from à to L will briefly switch off the headlamps. Doing so while driving in low ambient lighting conditions may result in an accident.
High-beam flasher X Switching on: Pull the combination switch briefly in direction of arrow = . Hazard warning flasher The hazard warning flasher can be switched on at all times, even with the SmartKey removed from the starter switch. The hazard warning flasher comes on automatically when an air bag deploys.
Driving in reverse: The front fog lamp opposite to your steering direction comes on. The corner-illuminating front fog lamps will come on automatically depending on the steering angle, even if you did not switch on either turn signal.
i If a door remains open, the interior lamps go out automatically after approximately 5 minutes when the SmartKey is removed or in starter switch position 0 . X Deactivating: Press button ~ . Button ~ engages. Manual control ! An interior lamp switched on manually does not go out automatically.
accumulates on a windshield/rear window might scratch the glass and/or damage the wiper blades when wiping occurs on a dry windshield/rear window. If it is necessary to operate the wipers in dry weather conditions, always operate the wipers with washer fluid.
Single wipe X Press the combination switch briefly in direction of arrow B to the resistance point. The windshield wipers wipe one time without washer fluid. Wiping with washer fluid X Press the combination switch in direction of arrow B past the resistance point.
If the windshield wipers fail to function at all with the combination switch in position Ä or Å , R set the combination switch to the next higher wiper speed R have the windshield wipers checked at .
Door windows X Switch on the ignition. X Opening/closing: Press or pull and hold switch : to ? to the resistance point. The corresponding window moves downward or upward until you release the switch. X Express operation: Press or pull switch : to ? past the resistance point and release.
Each door window must be synchronized separately. X Close all doors. X Switch on the ignition. X Pull and hold switch : , ; , = or ? ( Y page 107) until the respective door window is closed. The door window opens again slightly. X Pull and hold the respective switch once more immediately until the door window is closed completely.
anyone being harmed by the closing procedure. If potential danger exists, proceed as follows: R Release button & to stop the closing procedure. To open, press and hold button % . To continue the closing procedure after making sure that there is no danger of anyone being harmed by the closing procedure, press and hold button & .
windows and the tilt/sliding panel are closed completely. X Press and hold the lock button on an outside door handle again. The roller sunblinds extend.
With SmartKey X Do not depress the accelerator pedal. X Gasoline engine: Turn the SmartKey in the starter switch to position 3 ( Y page 79) and release it. The engine starts automatically. X Diesel engine: Turn the SmartKey in the starter switch to position 2 ( Y page 79).
The engine does not start. You can hear the starter. There could be a malfunction in the engine electronics or in the fuel supply system. Carry out the following steps: X If you are starting the engine with the SmartKey: Turn the SmartKey in the starter switch to position 0 and repeat the starting procedure.
idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
Parking G Warning! Do not park this vehicle in areas where combustible materials such as grass, hay or leaves can come into contact with the hot exhaust system. These materials could be ignited and cause a vehicle fire. Vehicle movement may result in serious personal injury or damage to the vehicle or vehicle drivetrain.
i Always engage the parking brake in addition to shifting the automatic transmission into park position P . i Observe instructions if you want the automatic transmission to remain in neutral position N , see “Remaining in neutral position N ” ( Y page 117).
! Allow the engine to warm up under low load use. Do not place full load on the engine until the operating temperature has been reached. Avoid spinning of a drive wheel for an extended period when driving off on slippery road surfaces.
KEYLESS-GO: When you turn off the engine using the KEYLESS-GO start/stop button and open a front door, the automatic transmission will shift into park position P automatically. G Warning! Keep in mind that turning off the engine alone only will shift the automatic transmission into neutral position N automatically.
Shifting into reverse gear R X With the vehicle at a standstill, depress the brake pedal. X Move the gear selector lever up past the resistance point. Shifting into drive position D X With the vehicle at a standstill, depress the brake pedal. X Move the gear selector lever down past the resistance point.
Effect A Neutral position No power is transmitted from the engine to the drive axle. When the brakes are released, the vehicle can be moved freely (pushed or towed). To avoid damage to the transmission, never shift the automatic transmission into neutral position N while driving.
The current gear range appears in the multifunction display. : Gear range indicator Effect = With this selection you can use the braking effect of the engine.
Steering wheel gearshift control i You cannot shift with the steering wheel gearshift control when the automatic transmission is in park position P , neutral position N , or reverse gear R . Limiting gear range G Warning! On slippery road surfaces, never downshift in order to obtain braking action.
Transfer case The vehicle is equipped with all-wheel drive (4MATIC). Both the front and rear axles are powered at all times when the vehicle is being operated. ! Only conduct operational or performance tests on a two-axle dynamometer. If such tests are necessary, contact an authorized Mercedes-Benz Center.
Adjusting the instrument cluster illumination X To brighten illumination: Press and hold button = until the desired level of illumination is reached. X To dim illumination: Press and hold button : until the desired level of illumination is reached.
: Multifunction display ; Press button 6 to answer a call to dial 8 to redial 8 ~ to end a call to reject an incoming call Press button W X to select submenus in the Settings menu to set values to set.
X Press button V or U repeatedly to pass through each menu one after the other. X Press button * or & repeatedly to pass through each function display, one after the other, in the current menu. In the Settings menu, instead of functions, you will find a number of submenus for calling up and changing settings.
Menus and submenus i The headings used in the menus table are designed to facilitate navigation within the system and are not necessarily identical to those shown in the multifunction display. The first function displayed in each menu will automatically show you which part of the system you are in.
The following functions are available: R Restarting the tire pressure loss warning system ( Y page 232) (Canada only) R Checking tire inflation pressure with the Advanced TPMS ( Y page 232) (USA only).
Audio/DVD menu The functions in the Audio/DVD menu operate the audio or video equipment which you have currently switched on. The following functions are available: R Selecting radio station ( Y page .
Operating video DVD X Switch on the COMAND system and select DVD-Video. Refer to separate COMAND system operating instructions. X Press button V or U repeatedly until the Audio/DVD menu appears in the multifunction display. : Disc number ; Current scene X Press button * or & to select a scene.
Vehicle status message memory menu Use the Vehicle status message memory menu to scan malfunction and warning messages that may be stored in the memory. Such messages appear in the multifunction display and are based on conditions or system status the vehicle’s system has recorded.
Resetting to factory settings You can reset the settings of all submenus to the factory settings. For safety reasons, the function Lamp Circuit Headlamp in the Lighting submenu cannot be reset while driving. The following message appears in the multifunction display: Settings Cannot be completely reset to factory settings when engine is running.
R Selecting language ( Y page 133) R Selecting display (digital speedometer or outside temperature) for status indicator ( Y page 133) Time/Date submenu R Setting the time ( Y page 133) R Setting the .
Speedometer appears in the multifunction display. The selection marker is on the current setting. X Press button W or X to set digital speedometer unit to Km or Miles . Selecting language X Press button V or U repeatedly until the Settings menu appears in the multifunction display.
X Press button V or U repeatedly until the Settings menu appears in the multifunction display. X Press button & . X Move the selection marker with button W or X to the Time/Date submenu. X Press button & or * repeatedly until the message Clock Set Hour or Clock Set Minute(s) appears in the multifunction display.
X Press button W or X to switch the daytime running lamp mode On or Off . With daytime running lamp mode switched on and the exterior lamp switch in position $ or à , the low-beam headlamps are switched on when the engine is running.
With the headlamps delayed shut-off feature activated and the exterior lamp switch in position à before the engine is turned off, the following lamps will come on when the engine is turned off: R Par.
Vehicle submenu Access the Vehicle submenu via the Settings menu. Use the Vehicle submenu to set the automatic central locking. Switching automatic central locking on or off Use this function to switch the automatic central locking on or off.
X Press button W or X to activate ( On ) or deactivate ( Off ) the easy-entry/exit feature. Activating/deactivating seat belt adjustment feature Use this feature to set the seat belts to be adjusted automatically with the driver’s or front passenger seat belt fastened and the starter switch in position 2 .
slower vehicle moving in your vehicle’s path and the danger of a collision exists, even when the Distronic is switched off. X Press button V or U repeatedly until the message Distance Warning appears in the multifunction display. The selection marker is on the current setting.
: Distance driven since last reset ; Time elapsed since last reset = Average speed since last reset ? Average fuel consumption since last reset Resetting fuel consumption statistics X Press button U or V repeatedly until the message From Start appears in the multifunction display.
separate COMAND system operating instructions. X Switch on the COMAND system. Refer to separate COMAND system operating instructions. X Press button U or V repeatedly until the message TEL appears in the multifunction display. One of the following messages will appear in the multifunction display: R No Service : No network is available.
Redialing The control system stores the most recently dialed phone numbers. This eliminates the need to search through your entire phone book. X Press button U or V repeatedly until the message TEL appears in the multifunction display. X Press button 6 .
G Warning! When the cruise control is braking, the brake pedal is retracted (i.e. depressed automatically). The pedals’ range of motion must not be impeded by any obstacles: R Do not place any objects in the footwell. R Make sure that the floormats and carpets are securely in place.
R the ESP ® has switched off due to a malfunction R you shift the automatic transmission into neutral position N while driving Observe additional messages in the multifunction display that may appear. Depressing the accelerator pedal does not deactivate the cruise control.
X Briefly pull the cruise control lever in direction of arrow ? . If no speed is stored, the current speed is set and stored. X Remove your foot from the accelerator pedal.
G Warning! Use of the Distronic can be dangerous on slippery roads. Rapid changes in tire traction can result in wheel spin and loss of control. The Distronic does not function in adverse sight and distance conditions. Do not use the Distronic during conditions of fog, heavy rain, snow or sleet.
The vehicle speed displayed on the speedometer can briefly vary from the speed setting on the Distronic system. When the Distronic detects a vehicle directly ahead, the cruise control speed segments ; appear in the speedometer. These segments represent the difference between the set speed of your vehicle : and the speed of the preceding vehicle = .
X Press button V or U repeatedly until one of the following two displays appears in the multifunction display. Distronic deactivated When the Distronic is deactivated, you will see the standard Distronic display in the multifunction display.
R when the automatic transmission is in park position P , reverse gear R , or neutral position N R when the ESP ® is switched off or has switched off due to a malfunction The vehicle speed displayed on the speedometer can briefly vary from the speed setting on the Distronic system.
Setting stored speed (Resume function) G Warning! The set speed stored in memory should only be set again if prevailing road conditions and legal speed limits permit. Possible acceleration or deceleration differences arising from returning to the preset speed could cause an accident and/or serious injury to you and others.
X Increasing distance: Turn distance setting switch : in direction of arrow = . Increasing the distance setting tells Distronic to maintain a greater following distance to the preceding vehicle. X Decreasing distance: Turn distance setting switch : in direction of arrow ; .
Offset driving A vehicle traveling in your lane but offset from your direct line of travel may not be detected by the Distronic. There will be insufficient distance to the preceding vehicle. Lane changing The Distronic has not yet detected the vehicle changing lanes.
X Activating/deactivating: Activate or deactivate the distance warning function in the control system ( Y page 138). When activated, the distance warning function indicator Ä appears in the multifunction display. Hill-start assist system G Warning! The hill-start assist system is not designed to function as a parking brake.
Indicator lamps ; and = are off. R SPORT (for sporty driving) Indicator lamp ; comes on. R COMF (for comfort driving) Indicator lamp = comes on. X Start the engine. X Press ADS switch : repeatedly until the desired suspension tuning is reached. The setting remains stored when you turn off the engine.
i The third available level is the highspeed level that is set automatically. The following is the approximate change in ride height for each of the level settings: Level Ride height Raised level +1.97 in (50 mm) Highway level +/-0 in (0 mm) Highspeed level -0.
X Close all doors and the tailgate. X Start the engine. When indicator lamp ; is on: X Press switch : . Indicator lamp ; flashes. The vehicle adjusts to the highway level.
distance between the vehicle and an obstacle visually and audibly. The Parktronic system is activated automatically when R you switch on the ignition and R you release the parking brake and R the auto.
Front sensors Center approx. 40 in (100 cm) Corners approx. 24 in (60 cm) Rear sensors Center approx. 48 in (120 cm) Corners approx. 32 in (80 cm) Minimum distance Center approx.
R Front area: An intermittent acoustic warning lasting a maximum of 2 seconds will sound as the first red distance segment illuminates. A constant acoustic warning lasting a maximum of 2 seconds will sound for the second red distance segment.
The area behind the vehicle appears in the COMAND system display as a mirror image, like in the rear view mirror. In addition, the rear view camera contains guidelines to help you with driving in reverse. G Warning! Make sure no persons or animals are in or near the area in which you are parking/ maneuvering.
Switching on/off X Switching on: Switch on the ignition. X Switch on the COMAND system. X Shift the automatic transmission to reverse gear R . The COMAND system display will show the area behind the vehicle with guidelines.
Overview of climate control system functions and air vents Your vehicle is equipped with either of the following climate control systems: Climate control ( Y page 164) 3-zone automatic climate control USA only ( Y page 170) Canada only ( Y page 172) The climate control combines an automatic heating and ventilation system with a cooling system.
For best possible performance of the climate control: X Keep the air intake grille in front of the windshield free of snow, leaves, sticks, and any other debris. X Always keep all air vents and grilles in the passenger compartment free from obstruction.
B-pillar air vents Vehicles with 3-zone automatic climate control (second row) only : Side air vent, adjustable ; Thumbwheel for air volume control X Opening/closing: Turn thumbwheel ; to the left or to the right.
Function Recommendation/Notes : Temperature control, driver’s side i Set the temperature to 72 ‡ (22†). ( Y page 168) ; Air distribution and air volume (automatic mode) i Switches on the automatic mode.
Function Recommendation/Notes I Rear window defroster ( Y page 180) J Air recirculation i Only use this function for a short time, e.g. in a tunnel. Otherwise, the windows can fog up due to lack of fresh air. ( Y page 169) K Interior temperature sensor L Climate control on/off i Switches on the climate control system.
If you press button ¦ to reactivate the climate control system, the defrosting mode is activated. Deactivating the rear climate control from the front X Deactivating: Press button ± . The indicator lamp in the button comes on. X Reactivating: Press button ± .
shown in air volume display G ( Y page 164). or X Press air distribution button ¯ , P , or O . The indicator lamp in button à goes out. The automatic operation of air distribution switches off. Setting the temperature You can adjust the air temperature on each side of the passenger compartment.
X Press button I to decrease or button K to increase air volume to the desired level. The air volume decreases/increases to the next lower/higher blower speed and heating switches to the temperature that was set before the front defroster was switched on.
i The manually selected air recirculation mode is deactivated automatically: R after 5 minutes if the outside temperature is below approximately 41‡ (5†) R after 5 minutes if the air conditioning .
Function Recommendation/Notes : Temperature control, driver’s side i Set the temperature to 72 ‡ (22†). ( Y page 176) ; Air distribution and air volume (automatic mode) i Switches on the automatic mode.
Function Recommendation/Notes K Interior temperature sensor L Climate control on/off i Switches on the climate control system. The indicator lamp in button ^ goes out. ( Y page 175) Canada only Function Recommendation/Notes : Temperature control, driver’s side i Set the temperature to 72‡ (22†).
Function Recommendation/Notes C Air distribution, passenger side (directs air through the windshield and side air vents) ( Y page 177) D Operating the rear climate control from the front ( Y page 175) E Temperature control, passenger side i Set the temperature to 72 ‡ (22†).
Function Recommendation/Notes O Interior temperature sensor P Adopting driver’s side settings for all zones ( Y page 180) Rear automatic climate control : Increasing air volume ; Temperature control.
Deactivating the climate control system G Warning! When the climate control system is switched off, the outside air supply and circulation are also switched off. Only choose this setting for a short time. Otherwise the windows could fog up, impairing visibility and endangering you and others.
Activating Moist air can fog up the windows. You can dehumidify the interior air with the air conditioning. X Press button Á again. The indicator lamp in the button comes on. The air conditioning uses the refrigerant R134a. This refrigerant is free of CFCs which are harmful to the ozone layer.
increments, preferably starting at 72‡ (22†). Front temperature with front climate control panel USA only X Increasing/decreasing: Turn temperature control : and/or C ( Y page 170) slightly clockwise or counterclockwise.
Symbol Driver’s side Symbol Passenger side Function ZM Directs air to the windshield and side air vents P Directs air through the center, side and rear passenger compartment air vents cO Directs air.
was set before the front defroster was switched on. The indicator lamp in button ¦ goes out. The indicator lamp in button Á comes on. or X Turn temperature control : and/or C (USA only) ( Y page 170) or : and/or E (Canada only) ( Y page 172) slightly in any direction.
i The manually selected air recirculation mode is deactivated automatically: R after 5 minutes if the outside temperature is below approximately 41‡ (5†) R after 5 minutes if the air conditioning .
X Switch on the ignition. X Switching on: Press button ª on the respective climate control panel. The indicator lamp in the button comes on. X Switching off: Press button ª again. The rear window defroster switches off when the battery voltage is too low.
Sunroof switch : Raising ; Opening = Closing With the sunroof closed or raised, you can slide the sunroof screen forward and back. Sunroof screen X Switch on the ignition. Opening X Opening manually: Press and hold the sunroof switch to the resistance point in direction of arrow ; .
Closing when the tilt/sliding sunroof is blocked G Warning! Make sure that nobody can become trapped and be seriously or even fatally injured when closing the tilt/sliding sunroof with greater force or without automatic reversal function. If the movement of the tilt/sliding sunroof is blocked during the closing procedure (e.
Panorama roof with power tilt/ sliding panel Extending and retracting the roller sunblinds The roller sunblinds only operate with the tilt/ sliding panel closed.
! Please keep in mind that weather conditions can sometimes change rapidly. Make sure to close the tilt/sliding panel when leaving the vehicle. If water enters the vehicle interior, vehicle electronics could be damaged which is not covered by the Mercedes-Benz Limited Warranty.
If the tilt/sliding panel is blocked again and opens slightly: X Immediately after the tilt/sliding panel was blocked and has opened, pull and hold the roof panel switch in direction of arrow = until the tilt/sliding panel is fully closed. The tilt sliding panel closes without automatic reversal function.
vehicle occupants unless the items are securely fastened in the vehicle. To help avoid personal injury during a collision or sudden maneuver, exercise care when transporting cargo. Do not pile luggage or cargo higher than the seat backrests. The cargo compartment is the preferred place to carry objects.
G Warning! Only use the roof rack when the basic carrier bars have been completely mounted. The left and right roof rails are only stabilized by means of the basic carrier bars being mounted. Follow the manufacturer’s installation instructions. Otherwise, an improperly attached roof rack system or its load could become detached from the vehicle.
Cargo tie down rings, cargo compartment Cargo tie down rings, second-row footwell Cargo tie-down rings, third-row footwell Hooks Two hooks are located on the rear compartment trim panels, one on each side. Use the hooks to secure light-weight items only.
Expanding cargo volume in part Folding third-row seats X Lower the head restraints of the third-row seats completely ( Y page 88). X Place seat belt in seat belt holder : . X Pull release handle ; on seat backrest = in direction of arrow. Seat backrest = is released.
X Pull seat backrest release strap : in direction of arrow. X Completely fold seat backrest ; forward so that it rests on seat cushion = (armrest position). Armrest position X Pull seat release strap ? in direction of arrow. The seat is released and flips up and forward.
point in direction of arrow as far as it will go. Seat and seat backrest : are unlocked. X Fold seat backrest : forward until it fully rests on seat cushion ; in a horizontal position. X Push down on folded seat backrest : until seat cushion ; engages in seat base.
maneuvers, or in an accident. If you slide under it, the belt would apply force at the abdomen or neck. That could cause serious or even fatal injuries.
X When the seat is unlocked, push seat backrest back until the seat engages audibly. Outboard second-row seat locked When the seat is locked, lock status indicator : is in hinged position and red marking ; is barely visible. Second-row middle seat Folded position X Pull seat release strap : of seat ; in direction of arrow.
Blind installed behind second-row seats X Removing: Roll up cargo compartment cover blind. X Push release button = . X Pull cargo compartment cover blind ? to the left. X Remove cargo compartment cover blind. X Installing: For installation behind second row seats, install the blind extensions ( Y page 195).
When not in use, you can attach the blind extensions to the cargo compartment cover blind. X With the cargo compartment cover blind installed behind third-row seats, insert extension guide rail A into mounting B . X Push blind extension into mounting B as far as it will go.
Installing the cargo net Cargo net installed behind the C-pillar : Holder ; Cargo net bar = Red button X Hang cargo net bar ; on holder : as indicated by the arrow. X Push cargo net bar ; forward into holder : in direction of arrow. X Engage lower cargo net bar.
Keep compartment lids closed. This will help to prevent stored objects from being thrown about and injuring vehicle occupants during R braking R vehicle maneuvers R an accident Glove box Depending on vehicle equipment, an AUX socket or a media interface is located in the glove box.
i If your vehicle is equipped with Rear Seat Entertainment Package, the storage compartment contains the DVD player (see separate operating instructions). i The Roadside Assistance button º ( Y page 210) and the Information button E ( Y page 210) are located in telephone tray = .
i If your vehicle is equipped with a 3-zone automatic climate control, the storage compartments are replaced by adjustable air vents ( Y page 164). Rear center console The rear center console is located between the second-row seats. The rear center console contains a storage compartment ( Y page 199) and a cup holder ( Y page 203).
cargo compartment fully ( Y page 190) without removing the rear center console. i The storage compartment and the cup holder in the rear center console are only illuminated, when the rear center console is installed in the most rearward position (position 0).
Card/ticket holder with bottle opener Cards and tickets can be inserted into the slot in the middle. The bottle opener is located underneath the card/ticket holder and has openers for screw caps = and crown caps ? . i With the card/ticket holder removed, you can also take the rubber inlet from the cup holder for cleaning.
X Push cup holder = in until it engages. X Close cover : . Cup holder in rear center console A cup holder is located in the rear center console between the second-row seats. Cup holders in third-row side trims Cup holders are located in the side trims of the third-row seats.
Vanity mirror The vanity mirror lamp only functions when the sun visor is engaged in mounting C . X Flip sun visor : down. X Lift up vanity mirror cover ? . Vanity mirror lamp = comes on. Rear door window sunshade This feature is only available in the USA.
X Removing ashtray insert: Push on ashtray insert ; and pull it out upwards. X Reinstalling ashtray insert: Insert ashtray insert ; into opening. X Push down ashtray insert ; until it engages. X Close cover : . Cigarette lighter G Observe Safety notes, see page 55.
minimum level, the power outlets are automatically switched off, to help preserve engine starting power. 12V Power outlets ! If you use all power outlets in the vehicle, make sure that the maximum current drawn does not exceed 55 A.
The 115V AC socket : provides an alternating current of 115 volts, which enables you to connect small electrical devices with a combined received power of 150 W at most. You can connect small devices such as game consoles, mobile phone chargers, laptops, etc.
monitoring services, connection and cellular air time. R vehicle battery power is available. R the relevant cellular phone network and GPS signals are available and pass the information on to the Response Center.
Emergency calls ! In order to activate the Tele Aid system, a subscriber agreement must be completed. To ensure your system is activated and operational, please press Information button E to perform the acquaintance call. Failure to complete either of these steps may result in a system that is not activated.
The Response Center will automatically contact local emergency officials with the vehicle’s approximate location if they receive an automatic SOS signal and cannot make voice contact with the vehicle occupants. Roadside Assistance button X Open the telephone tray ( Y page 198).
X Press and hold Information button : for longer than 2 seconds. A call to the Customer Assistance Center will be initiated. The indicator lamp in Information button : will flash while the call is in progress. The message Connecting Call will appear in the multifunction display and the COMAND system is muted.
Route guidance You will be prompted to confirm that route guidance to the entered address is to be started. X Select Yes using button = or ; on the COMAND system. X Press button 9 on the COMAND system to confirm. The system calculates the route and subsequently starts the route guidance to the defined address.
R you have subscribed to the Tele Aid service R the Tele Aid service has been activated properly R the necessary mobile phone, power supply and GPS coverage are available Garage door opener The integrated remote control can operate up to three separately controlled devices compatible with HomeLink ® or some other systems.
X Step 4: Using both hands, simultaneously press hand-held remote control button B and the desired signal transmitter button ( ; , = or ? ). Do not release the buttons until step 5 is completed. Indicator lamp : will flash, first slowly and then rapidly.
If you live in Canada or if you are having difficulties programming a gate operator (regardless of where you live) by using the programming procedures, replace step 4 with the following: X Step 4: Press and hold the signal transmitter button ( ; , = or ? ).
control is compatible with radio-frequency devices operating between 280-390 MHz . R Put a new battery in hand-held remote control A . This will increase the likelihood of the hand-held remote control sending a stronger and more accurate signal to the integrated remote control.
i If your vehicle is not equipped with AIRMATIC, the multifunction display will show the compass only. Floormats G Warning! Whenever you are using floormats, make sure there is enough clearance and that the floormats are securely fastened. Floormats should always be securely fastened using the fastening equipment.
218 251_AKB; 4; 52, en-US d2ureepe, Version: 2.11.8.1 2009-03-23T09:22:52+01:00 - Seite 218.
Vehicle equipment ............................ 220 The first 1000 miles (1500 km) ....... 220 At the gas station ............................. 220 Engine compartment ........................ 222 Tires and wheels ............................... 227 Winter driving .
Vehicle equipment i This Operator’s Manual describes all features, standard or optional, potentially available for your vehicle at the time of purchase. Please be aware that your vehicle might not be equipped with all features described in this manual.
drained completely. Contact an authorized Mercedes-Benz Center to have the fuel system drained completely. ! Gasoline engine: To prevent damage to the catalytic converters, only use premium unleaded gasoline in this vehicle. Any noticeable irregularities in engine operation should be repaired promptly.
i Leaving the engine running and the fuel filler cap open can cause the yellow fuel tank reserve warning lamp to flash and the malfunction indicator lamp ! (USA only) or ; (Canada only) to illuminate. For more information, see also “Practical hints” ( Y page 305).
vehicle. Comply with all relevant safety precautions. G Warning! To help prevent personal injury, stay clear of moving parts when the hood is open and the engine is running. The radiator fan may continue to run for approximately 30 seconds or may even restart after the engine has been turned off.
accident, for example. The hood could otherwise come loose while the vehicle is in motion and injure you and/or others. X Let the hood drop from a height of approximately 8 in (20 cm). X Check to make sure the hood is fully closed. If you can raise the hood at a point above the headlamps, then it is not properly closed.
For more information on engine oil, see “Fuels, coolants, lubricants etc.” ( Y page 350). For information on messages in the multifunction display concerning engine oil, see the “Practical hints” section ( Y page 293). Adding engine oil ! Only use approved engine oils and oil filters required for vehicles with Maintenance System.
hot fluid and steam will be blown out under pressure. R Do not spill antifreeze on hot engine parts. Antifreeze contains ethylene glycol which may burn if it comes into contact with hot engine parts. X Using a rag, slowly open cap ; approximately 1 / 2 turn to relieve excess pressure.
Brake fluid level ! If you find that the brake fluid in the brake fluid reservoir has fallen to the minimum mark or below, have the brake system checked for brake pad thickness and leaks immediately. Contact an authorized Mercedes-Benz Center immediately.
R Break in new tires for approximately 60 miles (100 km) at moderate speeds. R Regularly check the tires and rims for damage. Dented or bent rims can cause tire inflation pressure loss and damage to the tire beads. R If the vehicle is heavily loaded, check tire inflation pressure and correct as required.
The Tire and Loading Information placard lists the recommended cold tire inflation pressures : for maximum loaded vehicle weight. The tire inflation pressures listed apply to the tires installed as original equipment.
Example illustration: Tire inflation pressures for all approved, factory equipped tires Some tire inflation pressure labels may only show the rim diameter instead of the entire tire size, e.g. R 18 or 18" . The rim diameter is part of the tire size as specified on the tire sidewall ( Y page 245).
Do not overload the tires by exceeding the specified load limit as indicated on the Tire and Loading Information placard on the driver’s door B-pillar . Overloading the tires can overheat them, possibly causing a blowout. Overloading the tires can also result in handling or steering problems, or brake failure.
i The recommended tire inflation pressures for your vehicle can be found on R the Tire and Loading Information placard located on the driver’s door B-pillar ( Y page 236) R the tire inflation pressure label on the inside of the fuel filler flap The tire inflation pressures are not listed in the Operator’s Manual.
The TPMS is equipped with a combination low tire pressure/ TPMS malfunction telltale in the instrument cluster. Depending on how the telltale illuminates, it indicates a low tire pressure condition or a malfunction in the TPMS system itself: R If the telltale illuminates continuously, one or more of your tires is significantly underinflated.
malfunction using the TPMS telltale flashing and illumination sequence. The telltale extinguishes after a few minutes driving if the malfunction has been corrected. Tire pressure inquiries are made using the multifunction display. The current tire inflation pressure for each tire appears in the multifunction display after a few minutes of driving.
The respective tire is indicated by a red rectangle. Restarting Advanced TPMS G Warning! It is the driver’s responsibility to set the tire inflation pressure to the recommended cold tire inflation pressure. Underinflated tires affect the ability to steer or brake the vehicle.
punctured or damaged by road debris, potholes etc. i For illustration purposes only. Actual data on tires are specific to each vehicle and may vary from data shown in above illustration. This is the maximum permissible tire inflation pressure : for the tire.
Tire and Loading Information placard i Data shown on Tire and Loading Information placard example are for illustration purposes only. Load limit data are specific to each vehicle and may vary from data shown in the following illustration. Refer to Tire and Loading Information placard on vehicle for actual data specific to your vehicle.
X Step 5: Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. X Step 6 (if applicable): If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.
Example 1 Example 2 Example 3 Step 1 Combined weight limit of occupants and cargo from Tire and Loading Information placard 1 500 lbs 1 500 lbs 1 500 lbs Example 1 Example 2 Example 3 Step 2 Number of.
Weight Rating (GVWR) and the Gross Axle Weight Rating (GAWR) for either the front or rear axle. You can obtain the GVWR and GAWR from the certification label. The certification label can be found on the driver’s door B-pillar, see the “Technical data” section ( Y page 344).
You may only use the MOExtended system in conjunction with the tire pressure loss warning system ( Y page 231) or the Advanced TPMS ( Y page 232). i Vehicles with MOExtended system are not factory-equipped with a TIREFIT kit. When retrofitting with tires that do not have run-flat characteristics, e.
recommended minimum tire tread depth for winter tires is 1 / 6 in (4 mm). Treadwear indicator : appears as a solid band across the tread. Storing tires ! Keep unmounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease and fuels.
tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete.
dimension front vs. rear), tire rotation is not possible. If applicable to your vehicle’s tire configuration, tires can be rotated according to the tire manufacturer’s recommended intervals in the tire manufacturer’s warranty pamphlet located in your vehicle literature portfolio.
Tire size designation, load and speed rating : Tire width ; Aspect ratio in % = Radial tire code ? Rim diameter A Load index B Speed symbol i For illustration purposes only. Actual data on tires are specific to each vehicle and may vary from data shown in above illustration.
For example, a load rating of 91 corresponds to a maximum load of 1356 lb (615 kg) the tire is designed to support. See also “Maximum tire load” ( Y page 240) where the maximum load associated with the load index is indicated in kilograms and lbs.
Index Speed rating H M+S 14 up to 130 mph (210 km/h) V M+S 14 up to 149 mph (240 km/h) i Not all M+S rated tires provide special winter performance. Make sure the tires you use show M+S and the mountain/ snowflake i marking on the tire sidewall.
The TIN is a unique identifier. The TIN facilitates efforts by tire manufactures to notify purchasers in recall situations or other safety matters concerning tires.
radio, and heater, to the extent that these items are available as factory-installed equipment (whether installed or not). Air pressure The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi), kilopascal (kPa), or bar.
Maximum loaded vehicle weight The sum of curb weight, accessory weight, total load limit, and production options weight. Maximum permissible tire inflation pressure This number is the greatest amount of air pressure that should ever be put in the tire.
Tread The portion of a tire that comes into contact with the road. Treadwear indicators Narrow bands, sometimes called “wear bars” that show across the tread of a tire when only 1 / 16 in (1.6 mm) of tread remains. TWR (Tongue Weight Rating) Maximum permissible weight on trailer tongue.
Snow chains ! Vehicles with Adaptive Damping System (ADS): When driving with snow chains, do not select SPORT mode as this may result in damage to your vehicle.
bring road-salt-impaired braking efficiency back to normal. If the vehicle is parked after being driven on salt-treated roads, the braking efficiency should be tested as soon as possible after driving is resumed. G Warning! Make sure not to endanger any other road users when carrying out these braking maneuvers.
When using the engine’s braking power, a drive wheel may not spin for an extended period of time, e.g. on slippery road surfaces. This may cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited Warranty.
! Only conduct operational or performance tests on a two-axle dynamometer. If such tests are necessary, contact an authorized Mercedes-Benz Center. You could otherwise seriously damage the brake system or the transfer case which is not covered by the Mercedes-Benz Limited Warranty.
X Reduce vehicle speed. X Avoid track grooves in the road. X Apply brakes cautiously. Standing water ! Do not drive through flooded areas. Before driving through water, determine its depth. If you must drive through standing water, drive slowly to prevent water from entering the passenger compartment or the engine compartment.
Loading a trailer R When loading a trailer, you should observe that neither the permissible GTW, nor the Gross Vehicle Weight Rating (GVWR) are exceeded. The GVWR is indicated on the certification label located on the driver’s door B-pillar ( Y page 236).
X Make sure the automatic transmission is in park position P ( Y page 116). X Engage the parking brake for the vehicle ( Y page 114). X Start the engine ( Y page 110). X Vehicles with AIRMATIC: Set the vehicle level to highway ( Y page 154) and set the ADS to AUTO or COMF ( Y page 153).
Do not attempt to straighten out the tow vehicle and trailer by increasing the speed. R If the transmission shifts between gears on inclines repeatedly, shift to a lower gear range manually ( Y page 119). Select 4 , 3 , 2 or 1 . A lower gear and reduction of speed reduces the chance of engine overloading and/or overheating.
Control and operation of radio transmitter Safety notes G Warning! Please do not forget that your primary responsibility is to drive the vehicle. A driver’s attention to the road must always be his/her primary focus when driving.
Maintenance service indicator message The maintenance service indicator message will notify you when the next maintenance service is required. Starting approximately 1 month before the next maintenance service is required, one of the following messages will appear in the multifunction display.
Calling up the maintenance service indicator display i The menu overview can be found on ( Y page 126). You can call up the maintenance service indicator display at any time to check when the next maintenance service is required. X Switch on the ignition.
attack the paintwork as well as the vehicle underbody and cause lasting damage. Such damage is caused not only by extreme and varying climatic conditions, but also by: R Air pollution R Road salt R Ta.
Paintwork, painted body components ! Affixing stickers, magnets, adhesive tape or similar materials to painted body components may damage the paintwork. Mercedes-Benz approved Paint Care should be applied when water drops on the paint surface do not “bead up”.
X When taking the vehicle through an automatic conveyor-type car wash: Make sure the automatic transmission remains in neutral position N . Observe instructions, see “Remaining in neutral position N ” ( Y page 117). When leaving the automatic car wash, make sure the mirrors are folded out.
Cleaning the rear view camera lens X Only use clean water and a soft, non- scratching cloth to clean rear view camera lens : . Be careful not to apply wax to rear view camera lens : when waxing the vehicle. If necessary, remove the wax using the Mercedes-Benz approved Car Shampoo with plenty of water.
Light alloy wheels If possible, clean wheels once a week. X Use Mercedes-Benz approved Wheel Care, a soft bristle brush and a strong spray of water for cleaning the light alloy wheels. ! Only use acid-free cleaning materials. Acid may cause corrosion or damage the clear coat.
G Warning! Do not bleach or dye seat belts as this may severely weaken them. In a crash they may not be able to provide adequate protection. Upholstery Using aftermarket seat covers or wearing clothing that have the tendency to give off coloring (e.g.
Vehicle equipment ............................ 270 Where will I find ...? .......................... 270 Vehicle status messages in the multifunction display ....................... 274 What to do if … .................................. 299 Unlocking/locking manually .
Vehicle equipment i This Operator’s Manual describes all features, standard or optional, potentially available for your vehicle at the time of purchase. Please be aware that your vehicle might not be equipped with all features described in this manual.
X Engage securing hook = on upper cargo compartment lip ? . ! With the cargo compartment cover blind installed behind the third-row seats, disengage cargo compartment cover blind and flip it forward. Otherwise the strap of the securing hook could damage the cargo compartment cover blind.
Collapsible wheel chock The collapsible wheel chock serves to secure the vehicle, e.g. while changing a wheel. X Take the collapsible wheel chock from the vehicle tool kit ( Y page 270). X Setting up: Tilt both plates upward : . X Fold the lower plate outward ; .
X Removing: Open the tailgate ( Y page 75). X Lift the cargo compartment floor and secure it on the upper cargo compartment lip ( Y page 270). ! To prevent damage, always disengage the securing hook from upper cargo compartment lip and lower the cargo compartment floor before closing the tailgate.
Vehicle status messages in the multifunction display Notes Warning and malfunction messages appear in the multifunction display located in the instrument cluster. Certain warning and malfunction messages are accompanied by an audible signal. Address these messages accordingly and follow the additional instructions given in this Operator’s Manual.
Text messages Safety systems Display messages Possible causes/consequences and X Solutions ABS ABS, ESP Inoperativ e See Operator’s Manual The brake system is still functioning normally but due to a malfunction, the ABS, the BAS, the ESP ® , and the PRE- SAFE ® system are unavailable.
Display messages Possible causes/consequences and X Solutions ESP Unavailabl e See Operator’s Manual The brake system still functions normally but due to insufficient power supply the ESP ® , the BAS, and the PRE-SAFE ® system are unavailable. X Continue driving with added caution.
Display messages Possible causes/consequences and X Solutions Front Passenger Airbag Enabled See Operator’s Manual USA only: The front passenger front air bag is activated while driving even though a child, small individual, or object below the system’s weight threshold is on the front passenger seat, or the front passenger seat is empty.
Display messages Possible causes/consequences and X Solutions If above conditions are met, you can occupy the front passenger seat again. Depending on the front passenger classification sensed by the OCS, the 42 indicator lamp will remain illuminated or go out.
Display messages Possible causes/consequences and X Solutions Front Passenger Airbag Disabled See Operator’s Manual USA only: The front passenger front air bag is deactivated while driving even though an adult or someone larger than a small individual is occupying the front passenger seat.
G Warning! If the 42 indicator lamp remains illuminated with an adult occupant on the front passenger seat even after performing the above corrective steps, do not have any passenger use the front passenger seat until the system has been repaired.
Display messages Possible causes/consequences and X Solutions DISTRONIC Currently Unavailabl e See Operator’s Manual Distronic is deactivated because: R The Distronic cover in the radiator grille is dirty. R The functionality is impaired by heavy precipitation or fog.
Vehicle Display messages Possible causes/consequences and X Solutions Depress brake to shift out of P. You have attempted to shift the automatic transmission into drive position D , reverse gear R or neutral position N without depressing the brake pedal.
Tires Display messages Possible causes/consequences and X Solutions Check tires, then restart Run Flat Indicator. There has been a warning message about a loss in the tire inflation pressure and the tire pressure loss warning system was not restarted yet.
Display messages Possible causes/consequences and X Solutions Tire Pressure Monitor Wheel Sensor Missing At least one sensor is defect (e.g. battery is empty). The respective tire is indicated by – – instead of the tire inflation pressure in the multifunction display.
Display messages Possible causes/consequences and X Solutions Check Tire(s) The tire inflation pressure in at least one tire is significantly below the reference value. The respective tire is indicated in the multifunction display. X Carefully bring the vehicle to a halt, avoiding abrupt steering and braking maneuvers.
Display messages Possible causes/consequences and X Solutions $ (USA only) J (Canada only) EBV, ABS, ESP Inoperativ e See Operator’s Manual The brake system is still functioning normally but due to a malfunction, the ABS, the BAS, the EBP, the ESP ® , and the PRE-SAFE ® system are unavailable.
Safety systems Display messages Possible causes/consequences and X Solutions G Tele Aid Inoperativ e One or more main functions of the Tele Aid system are malfunctioning. X Have the Tele Aid system checked at an authorized Mercedes-Benz Center. + Restraint Sys.
Display messages Possible causes/consequences and X Solutions Á STOP Car Too Low You have driven off while the vehicle level was too low or the AIRMATIC is inoperative. The AIRMATIC should have raised the vehicle to the set level after a short while.
Display messages Possible causes/consequences and X Solutions ; You are driving with at least one door open. X Close all doors. + Key Detected In Vehicle A SmartKey with KEYLESS-GO left in the vehicle was recognized while trying to lock the vehicle from the outside.
Display messages Possible causes/consequences and X Solutions + Key Not Detected (message appears in white) The SmartKey with KEYLESS-GO is momentarily not detected. X Change the position of the SmartKey in the vehicle. X If necessary, remove the KEYLESS-GO button from the starter switch ( Y page 80).
Display messages Possible causes/consequences and X Solutions ? Coolant Stop car, switch engine off. The coolant is too hot. X Stop the vehicle immediately as soon as it is safe to do so. X Turn off the engine immediately. X Engage the parking brake. X Only start the engine again after the message disappears.
Display messages Possible causes/consequences and X Solutions ? Coolant Stop car, switch engine off. The poly-V-belt could be broken. X Stop the vehicle immediately as soon as it is safe to do so. X Turn off the engine immediately. X Check the poly-V-belt.
Display messages Possible causes/consequences and X Solutions # Battery/ Alternator Stop Vehicle The battery is defective. X Stop the vehicle in a safe location or as soon as it is safe to do so. X Engage the parking brake. X Do not continue to drive.
Display messages Possible causes/consequences and X Solutions 8 Gas Cap Open A loss of pressure has been detected in the fuel system. The fuel cap may not be closed properly or the fuel system may be leaky. X Check the fuel cap ( Y page 221). X If it is not closed properly: Close the fuel cap.
Lamps Display messages Possible causes/consequences and X Solutions b Active Headlamps Inoperativ e The active Bi-Xenon headlamp system is malfunctioning. X Contact an authorized Mercedes-Benz Center as soon as possible. b Reverse Lamp Left or Reverse Lamp Right The left or right backup lamp is malfunctioning.
Display messages Possible causes/consequences and X Solutions b Parking Lamp Front Left or Parking Lamp Front Right The left or right front parking lamp is malfunctioning. A substitute bulb is being used. X Replace the bulb as soon as possible ( Y page 312).
Display messages Possible causes/consequences and X Solutions b Switch Off Lights You have removed the SmartKey from the starter switch, opened the driver’s door and left the headlamps on or removed the SmartKey with KEYLESS-GO from the vehicle and left the headlamps on.
Display messages Possible causes/consequences and X Solutions b Turn Signal Rear Left or Turn Signal Rear Right The left or right rear turn signal lamp is malfunctioning. A substitute bulb is being used. X Replace the bulb as soon as possible ( Y page 312).
Display messages Possible causes/consequences and X Solutions h Tire Pressure Check Tires The tire inflation pressure in at least one tire is significantly below the reference value. X Carefully bring the vehicle to a halt, avoiding abrupt steering and braking maneuvers.
Brake Problem Possible causes/consequences and X Solutions ! The yellow ABS indicator lamp comes on while the engine is running. The ABS has detected a malfunction and switched off. The BAS, the ESP ® and the PRE-SAFE ® are also switched off. The brake system is still functioning normally but without the systems specified above available.
Problem Possible causes/consequences and X Solutions $ (USA only) J (Canada only) ! d The red brake warning lamp comes on while driving. In addition, the yellow ABS malfunction indicator lamp, and the yellow ESP ® warning lamp come on and an acoustic warning sounds.
Safety systems Problem Possible causes/consequences and X Solutions 7 The red seat belt telltale comes on for a maximum of 6 seconds after starting the engine. The seat belt telltale reminds you and your passengers to fasten your seat belts before driving off.
i After 60 seconds with an unfastened seat belt the warning chime stops sounding and the seat belt telltale illuminates continuously. The seat belt telltale will only go out if both, the driver and front passenger’s seat belt are fastened, or the vehicle is standing still and a front door is opened.
Problem Possible causes/consequences and X Solutions d The yellow ESP ® warning lamp flashes while driving. The ESP ® or the 4-ETS has come into operation because of detected traction loss in at least one tire. The cruise control is deactivated. X When driving off, apply as little throttle as possible.
Vehicle Problem Possible causes/consequences and X Solutions The yellow fuel tank reserve warning lamp in the fuel gauge comes on while driving. The fuel level has gone below the reserve mark.
Tires Problem Possible causes/consequences and X Solutions h USA only: Combination low tire pressure telltale/TPMS malfunction telltale for the Advanced TPMS illuminates continuously. The Advanced TPMS detects a loss of pressure in at least one tire. X Carefully bring the vehicle to a halt, avoiding abrupt steering and braking maneuvers.
sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended.
G Warning! If the 42 indicator lamp illuminates and remains illuminated with the weight of a typical adult or someone larger than a small individual on the front passenger seat, do not have any passenger use the front passenger seat until the system has been repaired.
SmartKey with KEYLESS-GO X Move locking tab : in the direction of arrow. X Slide mechanical key ; out of the housing. Unlocking the driver’s door X Insert mechanical key ; into the driver’s door lock. X Turn mechanical key ; counterclockwise to position 1 .
In case the central locking system does not release the fuel filler flap, you can open it manually. The fuel filler flap release is located on the passenger side in the cargo compartment behind the cover. X Open the tailgate ( Y page 75). X Open the cover on the passenger-side trim panel ( Y page 317).
have the batteries replaced at an authorized Mercedes-Benz Center. G Warning! Batteries contain poisonous and corrosive substances. Therefore, keep the batteries out of reach of children.
SmartKey with KEYLESS-GO X Insert mechanical key : into opening. X Press mechanical key : in direction of arrow. Battery compartment ; is unlatched. X Pull battery compartment ; out of the SmartKey housing. X Pull out batteries = . X Insert new batteries = under contact springs ? with the positive terminal (+) side facing up.
Bulbs You can replace the following bulbs yourself: Halogen headlamps Type : Turn signal lamp: 3457A ; Parking and standing lamp: W 5 W = Low-beam lamp: H7 55 W ? High-beam lamp/High-beam flasher lamp.
Rear lamps Type : Tail lamp, brake lamp, side marker lamp: P 21 W ; Turn signal lamp: PY 21 W = Rear fog lamp (driver’s side only): P 21 W ? Backup lamp: P 21 W License plate lamps Type : License plate lamps: C 5 W Notes on bulb replacement ! Do not replace LEDs or bulbs not described in this section.
Example illustration: Passenger side headlamp : Housing cover for low-beam and high- beam halogen or Bi-Xenon headlamp G Warning! Do not remove the cover for the Bi-Xenon headlamp. Because of high voltage in Xenon lamps, it is dangerous to replace the bulb or repair the lamp and its components.
X Place bulb socket ? back into the housing and turn it clockwise until it engages. X Align housing cover : and turn it clockwise until it engages. Front turn signal lamp bulb X Turn bulb socket ; with the bulb counterclockwise and remove it. X On both sides open catch A and pull bulb B out of bulb socket ; .
Opening the passenger-side trim panel X Insert a suitable object such as a coin into the slot of lock : . X Turn lock : by 90° in direction of the arrow.
G Warning! Wiper blades are components that are subject to wear and tear. Replace the wiper blades twice a year, preferably in the spring and fall. Otherwise the windows will not be wiped properly. As a result, you may not be able to observe surrounding traffic conditions and could cause an accident.
Installing wiper blades Front wiper blades X With guide tab = sliding into opening ? , place wiper blade : onto wiper arm in direction of arrow. X Fold wiper blade : towards wiper arm. Tabs ; ( Y page 318) must engage into both recesses of attachment ; .
Do not switch off the ESP ® when a spare wheel is mounted. G Warning! Vehicles with AIRMATIC: Do not open or close any doors or the tailgate while mounting a spare wheel. The vehicle could rise or lower to a previously selected level. You or others could be injured as a result.
Two-part sticker X Attach upper part : of the sticker where it will be easily seen by the driver on the instrument cluster. X Attach lower part ; of the sticker to the damaged tire (close to the tire valve). G Warning! Take care not to allow the contents of TIREFIT to come in contact with hair, eyes or clothing.
X Stick TIREFIT container : upside down into notch ; of the electric air pump. Example illustration X Unscrew the valve cap of the damaged tire from tire valve E . Version 1 X Version 1 only: Close vent screw F on pressure gauge G . X Screw filler hose D onto tire valve E .
damaged for TIREFIT to provide a reliable tire repair. In this case, TIREFIT cannot properly seal the tire. Do not drive the vehicle. Contact the nearest Mercedes-Benz Center or call Roadside Assistance. After attaining a tire inflation pressure of at least 26 psi (1.
(80 km/h) or below with the recommended tire inflation pressure. X Contact an authorized Mercedes-Benz Center as soon as possible to obtain a new TIREFIT kit. X Bring used TIREFIT materials to an authorized Mercedes-Benz Center for proper disposal. X Replace your TIREFIT container every 4 years.
X Prevent the vehicle from rolling away by blocking wheels with wheel chocks or other sizeable objects. When your vehicle is equipped with a wheel chock, it is included with the vehicle tool kit ( Y page 270). For information on setting up the collapsible wheel chock, see ( Y page 272).
X On the wheel to be changed, loosen but do not yet remove the wheel bolts (approximately one full turn with wheel wrench : ). X Assemble the jack ( Y page 272). The jack take-up brackets are located directly behind the front wheel housings and in front of the rear wheel housings.
Removing the wheel X Unscrew the uppermost wheel bolt and remove it. X Replace this wheel bolt with alignment bolt : . X Remove the remaining bolts. ! Do not place wheel bolts in sand or dirt. This could result in damage to the wheel bolts and wheel hub threads.
X Guide the spare wheel onto the alignment bolt and push it on. X Insert the wheel bolts and tighten them slightly. X Unscrew the alignment bolt. X Install the last wheel bolt and tighten it slightly.
! The cigarette lighter as well as the power outlets in the passenger footwell and cargo compartment are not designed for use with the electric air pump. Use the power outlet in the second-row footwell for electric air pump operation. X Turn the SmartKey in the starter switch to position 1 .
X Tighten the five wheel bolts evenly, following the diagonal sequence illustrated ( : to A ), until all bolts are tight. Observe a tightening torque of 110 lb-ft (150 Nm). G Warning! Have the tightening torque checked after changing a wheel. The wheels could come loose if they are not tightened to a torque of 110 lb-ft (150 Nm).
After driving in emergency mode, you must have the rims inspected by an authorized Mercedes-Benz Center to check if they are suitable for further use. The failed tire must be replaced in any case.
Always use the particular AdBlue ® refill containers for refilling outside the maintenance service interval. Contact an authorized Mercedes-Benz Center or call Roadside Assistance if necessary ( Y page 210). Additional information on BlueTEC exhaust gas aftertreatment and AdBlue ® is available at any authorized Mercedes-Benz Center.
X Turn AdBlue ® filler cap ? counterclockwise and open it. Filler cap ? is tethered with a plastic strap. X Pull dust cap off of AdBlue ® refill container A . X Place AdBlue ® refill container A on the filler neck as illustrated and tighten it moderately (hand-tight) by turning it clockwise.
life. Refer to Maintenance Booklet for battery maintenance intervals. If you use your vehicle mostly for short- distance trips, you will need to have the battery charge checked more frequently. When replacing a battery, always use a battery approved by Mercedes-Benz.
battery cover is non-removable. Do not attempt to open the battery as otherwise the battery will be damaged. VRLA batteries do not require topping-up of the electrolyte level. They cannot be opened to check the electrolyte level. However, the battery condition must be checked periodically by performing a battery conductance test.
Only use a battery charge unit with a maximum charging voltage of 14.8 V. X Charge battery in accordance with the instructions of the battery charger manufacturer. Jump starting G Warning! Failure to follow these directions will cause damage to the electronic components, and can lead to a battery explosion and severe injury or death.
that move when an engine is started or running. R Should the battery be drained completely, let the donating power source charge the vehicle for several minutes before reattempting the starting process. The jump-start contacts are located in the engine compartment on the passenger side.
X Slide cover A back onto negative terminal B . X Have the battery checked at the nearest authorized Mercedes-Benz Center. Towing the vehicle Safety notes Mercedes-Benz recommends that the vehicle be transported with all wheels off the ground using flatbed or appropriate wheel lift/dolly equipment.
Removing cover in front bumper X Press mark on cover : as indicated by the arrow. X Lift cover : off to reveal the threaded hole for the towing eye bolt. Removing cover in rear bumper G Warning! In order to avoid possible serious burns or injury, use extreme caution when removing the rear cover, because the rear exhaust pipe is extremely hot.
Towing with all wheels on the ground G Warning! If circumstances require towing the vehicle with all wheels on the ground, always tow with a tow bar if: R the engine will not run R there is a malfunct.
A blown fuse must be replaced by an appropriate spare fuse (recognizable by its color or the fuse rating given on the fuse) of the amperage recommended in the fuse chart. Any Mercedes-Benz Center will be glad to advise you on this subject. i In case of a blown fuse contact Roadside Assistance or an authorized Mercedes- Benz Center.
X Closing: Make sure the sealing rubber is positioned properly. X Insert the tabs of fuse box cover ; that are opposite of clamp : into the openings. X Press fuse box cover ; down X Close clamp : . ! The fuse box cover must be properly positioned as described.
Vehicle equipment ............................ 344 Parts service ..................................... 344 Warranty coverage ........................... 344 Identification labels .......................... 344 Vehicle specification R 350 Blue- TEC (251.
Vehicle equipment i This Operator’s Manual describes all features, standard or optional, potentially available for your vehicle at the time of purchase. Please be aware that your vehicle might not be equipped with all features described in this manual.
The Vehicle Identification Number (VIN) can be found R on certification label : on the driver’s door B-pillar R on passenger side underneath the second- row seat ( Y page 345) R on the lower edge of the windshield ( Y page 345) Example certification label (U.
Vehicle specification R 350 BlueTEC (251.125) The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment. Engine R 350 BlueTEC Engine, type 642 Mode of operation Diesel 4-stroke engine No.
Engine R 350 Compression ratio 10.7:1 Output acc. to SAE J 1349 22 268 hp/6 000 rpm (200 kW/6 000 rpm) Maximum torque acc. to SAE J 1349 258 lb-ft/ 2 400 - 5 000 rpm (350 Nm/ 2 400 - 5 000 rpm) Maximum engine speed 6 500 rpm Firing order 1-4-3-6-2-5 Poly-V-belt 2 404 mm Electrical system R 350 Alternator 14 V/180 A Starter motor 12 V/1.
i Vehicles with MOExtended system are not factory-equipped with a TIREFIT kit. When retrofitting with tires that do not have run-flat characteristics, you should also equip your vehicle with a TIREFIT kit. TIREFIT kits are available at any authorized Mercedes-Benz Center.
Same size tires Model R 350 BlueTEC 19" wheels Rims (light alloy) Wheel offset 8 J x 19 H2 2.64 in (67 mm) All-season tires 25,26 255/50 R19 107H XL (Extra Load) M+S MOExtended Winter tires 25,26,27 255/50 R19 107H XL (Extra Load) M+S i MOExtended Model R 350 19" wheels Rims (light alloy) Wheel offset 8 J x 19 H2 2.
Spare wheel ! Compare the recommended tire inflation pressure for your vehicle with the tire inflation pressure on the yellow label located on the spare wheel rim.
Model Capacity Fuels, coolants, lubricants, etc. Front axle All models 1.2 US qt (1.1 l) Hypoid gear oil Rear axle All models 1.2 US qt (1.1 l) Hypoid gear oil Transfer case All models 0.53 US qt (0.5 l) MB Automatic Transmission Fluid Power steering All models approx.
Approved engine oils Engine oils are specifically tested for their suitability in our engines and durability for our service intervals. Therefore, only use approved engine oils and oil filters required for vehicles with the Maintenance System.
the formation of bubbles in the system, thus reducing the system’s efficiency. Therefore, the brake fluid must be replaced regularly. Refer to your vehicle’s Maintenance Booklet for replacement interval. Only brake fluid approved by Mercedes-Benz is recommended.
! Do not fill the tank with gasoline. Do not blend diesel fuel with gasoline or kerosene. The fuel system and engine will otherwise be damaged, which is not covered by the Mercedes-Benz Limited Warranty. For further information on diesel fuel pump labeling, contact an authorized Mercedes- Benz Center or visit www.
immediately. If AdBlue ® has crystallized already, use cold water and a sponge. AdBlue ® residues will crystallize and soil the affected surfaces. High ambient temperatures If AdBlue ® in the reser.
coolant concentration or bring it back up to the proper level. For information on other Mercedes-Benz approved products of equal specification, contact an authorized Mercedes-Benz Center or visit www.
Model Approximate freeze protection -35‡ (-37†) -49‡ (-45†) Cooling system All models 5.0 US qt (4.75 l) 5.5 US qt (5.2 l) Washer system and headlamp cleaning system G Warning! Washer solvent/antifreeze is highly flammable. Do not spill washer solvent/ antifreeze on hot engine parts, because it may ignite and burn.
358 251_AKB; 4; 52, en-US d2ureepe, Version: 2.11.8.1 2009-03-23T09:22:52+01:00 - Seite 358.
359 251_AKB; 4; 52, en-US d2ureepe, Version: 2.11.8.1 2009-03-23T09:22:52+01:00 - Seite 359.
360 251_AKB; 4; 52, en-US d2ureepe, Version: 2.11.8.1 2009-03-23T09:22:52+01:00 - Seite 360.
Service and Literature Your authorized Mercedes-Benz Center has trained technicians and Genuine Mercedes- Benz Parts to service your vehicle properly. For expert advice and quality service, contact an authorized Mercedes-Benz Center.
Order no. 6515 1833 13 Part no. 251 584 30 82 Edition A 2010 É2515843082_ËÍ 2515843082 251_AKB; 4; 52, en-US d2ureepe, Version: 2.11.8.1 2009-03-23T09:22:52+01:00 - Seite 362.
デバイスMercedes-Benz 2010 R350 BlueTECの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Mercedes-Benz 2010 R350 BlueTECをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMercedes-Benz 2010 R350 BlueTECの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Mercedes-Benz 2010 R350 BlueTECの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Mercedes-Benz 2010 R350 BlueTECで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Mercedes-Benz 2010 R350 BlueTECを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMercedes-Benz 2010 R350 BlueTECの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Mercedes-Benz 2010 R350 BlueTECに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMercedes-Benz 2010 R350 BlueTECデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
