Mercuryメーカー1999 Villagerの使用説明書/サービス説明書
ページ先へ移動 of 264
Before driving Introduction 2 Instrumentation 3 Controls and features 19 Seating and safety restraints 110 Starting and driving Starting 152 Driving 157 Roadside emergencies 171 Servicing Maintenance and care 191 Capacities and specifications 235 Customer assistance 241 Reporting safety defects 254 Index 255 All rights reserved.
ICONS Indicates a safety alert. Read the following section on W arnings. Indicates vehicle information related to recycling and other environmental concerns will follow . Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment.
Instrumentation 3.
OFF AUTO 1 AUTO 2 PUSH INTERIOR C E F H 1/2 FUEL TEMP N O R M A L 0 0 0 0 20 30 40 50 60 70 80 90 40 60 80 100 120 140 0 2 3 4 5 6 7 1 CRUISE OFF CANCEL RES ACCEL COAST SET VOL NEXT VOL DIM Panel dimmer (pg. 19) Headlamp control (pg. 19) Speed control (pg.
OFF REAR 1 2 3 4 1 MAX A/C A/C OFF 2 3 4 OVERDRIVE OFF/ON FF REW SIDE 1 - 2 BASS TREB BAL FADE TAPE AMS AM FM CD CLK VOL - PUSH ON SHUFFLE COMP CD EJ CD SCAN DISCS TUNE SEEK 3 2 14 5 6 DC 12V SECURITY HAZARD RR DEFOG RR WIPER RR WASH Gearshift (including overdrive button) (pg.
W ARNING LIGHTS AND CHIMES Standard analog instrument cluster Optional electronic instrument cluster Charging system Illuminates when the ignition is turned to the ON position and the engine is off. The light also illuminates when the battery is not charging properly , requiring electrical system service.
Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter . Brake system warning Momentarily illuminates when the ignition is turned to the ON position.
T urn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster , check for a burned-out turn signal bulb. Refer to Exterior bulbs in the Maintenance and care chapter .
Service engine soon Y our vehicle is equipped with a computer that monitors the engine’ s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). The OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
Light is blinking: Engine misfire is occurring which could damage your catalytic converter . Y ou should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity .
Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the ignition is off (and the key is not in the ignition) and the driver’ s door is opened. GAUGES Standard analog instrument cluster gauges Optional electronic instrument cluster gauges T achometer Indicates the engine speed in revolutions per minute.
• Standard analog instrument cluster • Optional electronic instrument cluster Speedometer Indicates the current vehicle speed. • Standard analog instrument cluster • Optional electronic instru.
Odometer Registers the total kilometers (miles) of the vehicle. • Standard analog instrument cluster • Optional electronic instrument cluster Refer to Electronic Message Center for information on how to switch the display from metric to English measurements.
empty indication, the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel. • Standard analog instrument cluster • Optional electronic instrument cluster Engine coolant temperature gauge Indicates the temperature of the engine coolant.
• Optional electronic instrument cluster ELECTRONIC MESSAGE CENTER (IF EQUIPPED) The electronic message center only works when the ignition is in the ON position. The message center allows you to: • display the outside temperature. • change your gauges from english to metric units.
• OUTSIDE TEMP • INST ECONOMY • A VG ECONOMY • TO EMPTY RESET Press this control to reset the average fuel economy calculation. ENG/MET Press this control to change your instrument cluster gauges from english to metric.
INST ECONOMY Press SELECT until the menu displays INST ECONOMY . This will display your fuel economy in liters/100 km or miles/gallon based on the type of traffic you are in. Y our vehicle must be moving to calculate instantaneous fuel economy . When your vehicle is not moving, this function shows 99.
2. Select A VG ECONOMY . 3. Press the RESET control to clear the system memory . • Actual highway fuel economy is now displayed. This current average measure will change as the speed control system changes the engine speed to maintain a constant vehicle speed.
P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. • Push and hold top of control to brighten. • Push and hold bottom of control to dim. HEADLAMP CONTROL Rotate the headlamp control clockwise to the first position to turn on the parking lamps.
High beams Push forward to activate. Pull toward you to deactivate. Flash to pass Pull toward you to activate and release to deactivate. AUTOLAMP CONTROL (IF EQUIPPED) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
CLIMATE CONTROL SYSTEM Manual heating and air conditioning system Fan speed control Controls the volume of air circulated in the vehicle. T emperature control Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
The air conditioning operates in MAX A/C and when the A/C control is depressed. However , the air conditioning will only function if the outside temperature is about 4°C (40°F) or higher .
and air conditioning capabilities are provided in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot and full cold positions, the air distributed through the front and rear floor ducts will be slightly warmer than the air sent to the windshield defroster ducts.
Rear seat heating Rear seat heating is provided through the floor ducts located under the front seats. Airflow and temperature to the rear seating are regulated by the main climate control system. The rear passenger compartment air conditioning system (if equipped) should be set to OFF , if rear heating is desired.
• Remove any snow , ice or leaves from the air intake area (at the bottom of the windshield under the hood). • If your vehicle has been parked with the windows closed during hot weather , the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
The rear A/C fan speed control allows the rear passengers to control the volume of air that is distributed from the rear registers. The rear seat A/C system is controlled from the main climate control system on the instrument panel.
T urning the Rear A/C on 1. Set the main climate control rear fan control to Rear A/C, set the mode selector in any position (other than OFF), and depress the A/C control.
T urning the Rear A/C off: T o turn the Rear A/C off, turn the Rear Fan Control on the main climate control system to OFF , or turn the Rear Fan Control on the main climate control system to Rear A/C and turn the Rear A/C Fan Control to 0. For maximum cooling for the front seat passengers, set the rear fan switch to the OFF (0) position.
Electronic Automatic T emperature Control (EA TC) system (if equipped) The EA TC system will maintain a selected temperature and automatically control airflow . Y ou can override automatic operation with any of the override controls or the fan speed control.
Turning the EA TC off Press OFF . Automatic operation Press AUTOMA TIC and select the desired temperature. The selected temperature and the word AUTO will appear in the display window . The EA TC system will either heat or cool to achieve the selected temperature.
T o control the temperature, select any temperature between 15°C (60°F) and 32°C (90°F) by pressing the temperature controls. For continuous maximum cooling, push the temperature control until 15°C (60°F) is shown in the display window .
Fan speed ( ) When AUTOMA TIC is pressed, fan speed is adjusted automatically for existing conditions. Y ou can override fan speed at any time. T o control fan speed manually , use the thumbwheel to cancel automatic fan speed operation. Rotate the thumbwheel up for higher fan speed or down for lower fan speed.
Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle.
• MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C A/C but more economical and will cool the inside of the vehicle faster . After pressing the MAX control, both the MAX and A/C A/C indicators will light and the airflow will be from the instrument panel registers.
Rear seat heating Rear seat heating is provided through the floor ducts located under the front seats. Airflow and temperature to the rear seating are regulated by the main climate control system. The rear passenger compartment air conditioning system (if equipped) should be set to OFF , if rear heating is desired.
• Remove any snow , ice or leaves from the air intake area (at the bottom of the windshield). • If your vehicle has been parked with the windows closed during hot weather , the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
The rear A/C fan speed control allows rear passengers to control the volume of air that is distributed from the rear registers. The rear A/C system is controlled from the main climate control system on the instrument panel. The rear seat A/C system is controlled from the main climate control system on the instrument panel.
T urning the Rear A/C on 1. Set the main climate control rear fan control to Rear A/C, set the mode selector in any position (other than OFF), and depress the A/C control.
turn the Rear Fan Control on the main climate control system to Rear A/C and turn the Rear A/C Fan Control to 0. For maximum cooling for the front seat passengers, set the rear fan switch to the OFF (0) position.
The ignition must be in the ON position to operate the rear window defroster . The defroster turns off automatically after 15 minutes or when the ignition is turned to the OFF position. T o manually turn off the defroster before 15 minutes have passed, push the control again.
T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD changer modes (if equipped).
Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly . • Press to move to the next frequency up the band (whether or not a listenable station is located there).
• Press to seek forward to the next track of the current disc. After the last track has been completed, the first track of the current disc will automatically replay .
Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers.
T ape select • T o enter tape mode while in radio or CD changer mode, press the T APE control. • If no tape is found, NO T APE appears in the display . Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection being played or to skip to the next selection.
Press the 1–2/FF control to stop rewinding the tape. T o rewind in CD changer mode, press the CD control (preset 1). Press the control again to deactivate rewind mode. Fast forward The fast forward control works in tape and CD changer modes. T o fast forward in tape mode, press the 1–2/FF control.
The shuffle feature continues to the next disc after all tracks are played. Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again. T ape direction select Press SIDE and 1–2 at the same time to play the alternate side of a tape.
• to decrease hours and • to increase hours. T o set the minute, press and hold the CLK control and press the TUNE control: • to decrease minutes and • to increase minutes. The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.
Rear seat controls (if equipped) The Rear Seat Controls (RSC) allow the rear seat passengers to operate the radio, tape, or CD changer (if equipped). T o turn on the rear seat controls, press the memory preset controls 3 and 5 at the same time. The will appear in the radio display .
Using headphones Plug a 3.6 mm headphone (not included) into either one of the two jacks. Press the / control to operate the headphones. The speakers will cut out once the speaker on/off control is pressed. Press the / control again to deactivate headphones.
Premium AM/FM Cassette (CD changer compatible) Y our audio system is equipped with selective lighting, a unique lighting strategy . This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off.
T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD changer modes (if equipped).
disc unless the CD changer is in shuffle mode.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the disc. • Press to select the next disc in the CD changer . Hold the control to fast-forward through the remaining discs.
Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape.
Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing.
Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. T ape/CD changer mode select (if equipped) • T o begin tape play (with a tape loaded into the audio system) while in the radio or CD changer mode, press the T APE control.
• In CD changer mode, pressing the control for less than three seconds results in slow forward action. Pressing the control for more than three seconds results in fast forward action. T ape direction select Press SIDE 1–2 to play the alternate side of a tape.
Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again. Radio Data System (RDS) feature When selected, the RDS (Radio Data System) .
• Use the SEL control to select the program type. W ith the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: • Classic • Country • Info .
Use the SEL control to manually set the time. • Press to increase hours/minutes. • Press to decrease hours/minutes. Mute mode Press the control to mute the playing media.
Adjusting the volume Press the + control to increase volume. Press the — control to decrease volume. From the RSC, the speaker volume can not be set higher than the current volume radio setting.
Memory preset control Push the MEM control successively to allow rear sear passengers to scroll through the 6 memory presets in AM, FM1, or FM2. Push the MEM control in CD changer mode (if equipped) to advance to the next disc. Seek function • Press to find the next listenable station down the frequency band.
Y our audio system is equipped with selective lighting, a unique lighting strategy . This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off.
AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play . AM/FM select in CD mode Press this control to stop CD play and begin radio play .
Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Seek function in tape mode • Press to listen to the previous selection on the tape.
Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’ s first side, direction automatically reverses to the opposite side of the tape.
Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing.
• to decrease treble output and • to increase treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: • to shift sound to the left and • to shift sound to the right.
T ape/CD/CD changer (if equipped) select • T o begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the T APE control. Press the button during rewind or fast forward to stop the rewind or fast forward function.
T ape direction select Press SIDE 1–2 to play the alternate side of a tape. Eject function Press the control to stop and eject a tape. Press the control to stop and eject a CD. Dolby noise reduction Dolby noise reduction reduces the amount of hiss and static during tape playback.
Setting the clock Press the RDS/CLK control until SELECT HOUR is displayed and press: • to decrease hours and • to increase hours. T o set the minute, press the RDS/CLK control until SELECT MIN is displayed and press: • to decrease minutes and • to increase minutes.
Press the RDS control. Use the SEL control to select ON or OFF to enable or disable the feature. RDS traffic announcement When set ON, this traffic feature will interrupt tape or CD play to play a traffic report broadcast from a FM RDS station. T o activate the traffic feature: • Press the RDS control until TRAFFIC is displayed.
• Jazz/R&B • Religious • Rock • Soft • To p 4 0 RDS show RDS sends information with the FM broadcast, including: station name, station type, and/or radio text. T o view this information: • W ith the RDS menu enabled, press the RDS control until SHOW is displayed.
T o turn on the rear seat controls, press the memory preset controls 3 and 5 at the same time. The will appear in the radio display . Pressing 3 and 5 at the same time again will turn the rear seat controls off. If there is a discrepancy between the rear seat and the front audio controls, (i.
The rear speakers will cut out once the speaker on/off control is pressed. A soft audible sound may be heard from the rear speakers. The front speaker will remain playing for the front passengers. Press the / control again to deactivate headphones (Personal Audio System).
CD changer (if equipped) The CD changer is located in the center console of your vehicle. 1. Slide the door to access the CD changer magazine. 2. Press to eject the magazine. 3. T urn the magazine (A) over . 4. Using the disc holder release knob (C), pull the disc holder (B) out of the magazine.
If you pull too hard on the disc holder , the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A). 5. Line up the CD with the groove of the disc holder .
The CD magazine may be inserted or ejected with the radio power on or off. ONL Y use the magazine type supplied with the CD changer , other types will damage the unit. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty .
Cleaning cassette player Clean the tape player head with a cassette cleaning cartridge after ten to twelve hours of play in order to maintain the best sound and operation. Cassette and cassette player care • Use only cassettes that are 90 minutes long or less.
• Station overload. W eak signals are sometimes captured by stronger signals when you pass a broadcast tower . A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed.
POSITIONS OF THE IGNITION 1. OFF/LOCK, shuts off the engine and all accessories/locks the steering wheel, gearshift lever and allows key removal. 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running. 3.
T o turn speed control off • Press OFF . Once speed control is switched off, the previously programmed set speed will be erased. T o set a speed • Press COAST/SET . For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).
T o set a higher set speed • Press and hold RES/ACCEL. Release the control when the desired vehicle speed is reached or • Press and release RES/ACCEL. Each press will increase the set speed by 1.6 km/h (1 mph) or • Accelerate with your accelerator pedal.
T o disengage speed control • Depress the brake pedal. • Press CANCEL. Disengaging the speed control will not erase the previously programmed set speed.
T o return to a previously set speed • Press RES/ACCEL. For RES/ACCEL to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on in the instrument cluster when either the COAST/SET or RES/ACCEL controls are pressed.
In any mode: • Press VOL up or down to adjust the volume. TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position.
Rear window wiper and washer Press the wiper control to activate the rear wiper . Press again to turn off the wiper . The wiper operates at a pre-set interval. Press the washer control to activate the rear washer . The wiper will come on when the washer control is pressed, if it is not already on.
Deactivating overdrive Press the T ransmission Control Switch (TCS) located on the end of the gearshift lever . The O/D OFF indicator light will illuminate. The transaxle will operate in all gears except overdrive. T o return to normal overdrive mode, press the T ransmission Control Switch again.
POWER WINDOWS • Press and hold the switch to open. • Pull up and hold the switch to close. Power vent windows (if equipped) Y our vehicle may be equipped with rear power vent windows which are operated the same as the front power windows. One touch down • Press AUTO completely down and release quickly .
Accessory delay W ith accessory delay , the window and moonroof switches may be used for up to 15 minutes after the ignition switch is turned to the OFF position or until either of the front doors are opened. POWER DOOR LOCKS Push control forward to unlock all doors and pull backward to lock all doors.
Pull lock control out to engage the lock. Push control in to disengage childproof locks. POWER SIDE VIEW MIRRORS The ignition must be in ACC or ON position to adjust the power side view mirrors. T o adjust your mirrors: 1. Select L to adjust the left mirror or R to adjust the right mirror .
2. Move the control in the direction you wish to tilt the mirror . 3. Return to the center position to lock mirrors in place. Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated.
HOMELINK T UNIVERSAL T RANSCEIVER WITH T RAVELNOTE T (IF EQUIPPED) The HomeLink t Universal T ransceiver , located on the driver’ s visor , provides a convenient way to replace up to three hand-held transmitters with a single built-in device.
4. The red light will flash slowly and then rapidly . Release both buttons when the red light flashes rapidly . 5. Follow steps 2 through 4 to program the remaining two buttons.
• The hand-held transmitter appears to program the HomeLink t Universal T ransceiver but does not activate the device. • Press and hold the trained HomeLink t button. The device has the rolling code feature if the indicator light flashes rapidly and then turns solid after 2 seconds.
1. Press and hold the desired HomeLink t button. Do NOT release until step 4 has been completed. 2. When the indicator light begins to flash slowly (after 20 seconds), position the hand-held transmitter 5–14 cm (2 to 5 inches) away from the HomeLink t surface.
T o play a message: 1. Press and release the PLA Y button to play the message. 2. Press and hold the PLA Y button to hear all the messages in consecutive order starting with the most recent. 3. If the PLA Y button is pressed while a message is being listened to, T ravelNote will skip to the beginning of the next message.
Storage bin (if equipped) The storage compartment may be used to store small objects. Push in to open or close the cover . Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Remove the GARAGE control button from the storage compartment.
• Place the provided height adaptors on the back of the GARAGE control button as needed. • Place the GARAGE control button in the storage compartment. • Close cover and press the GARAGE control button to activate the transmitter . INTERIOR LAMPS Dome lamps The front dome lamp is located overhead between the driver and passenger seats.
MOON ROOF (IF EQUIPPED) T o operate the moon roof: • T o open, press and hold the rear portion of the control. This will fully open the moon roof. • T o close, press and hold the front portion of the control. T o operate the moon roof vent position: • T o open, press and hold the front portion of the control.
Unlocking the doors Press this control to unlock the driver’ s door . The interior lamps will illuminate and the parking and tail lamps will flash once. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors.
This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
T o replace the battery: 1. T wist a thin coin between the two halves of the transmitter near the key ring. DO NOT T AKE THE FRONT P ART OF THE TRANSMITTER AP ART . 2. Place the positive (+) side of new battery up. Refer to the diagram inside the transmitter unit.
ANTI-THEFT SYSTEM (IF EQUIPPED) When armed, the anti-theft system will help prevent your vehicle from unauthorized entry . If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting.
If a door is open, the system is prearmed and is waiting for the door to close. Once all the doors are closed, the security indicator lamp on the instrument panel will illuminate continuously when the system is prearmed. Once the doors are closed, the system will arm in 30 seconds and the security indicator lamp will begin to flash.
Disarming a triggered anti-theft system Y ou can disarm the system by any of the following actions: • Press the unlock control. • Unlock the doors with a key . LIFTGATE T o open the liftgate window (if equipped), insert key into lock and turn clockwise.
Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle.
Front Cargo net The front cargo net can be used to hold small items between the front seats. T o install the net, secure the hooks into the retainers located on the inboard base of the front seats. Parcel Shelf (if equipped) Y our vehicle may be equipped with a 14 kg (30 lbs.
T o secure objects on the shelf: 1. Disconnect the net loops from the retainers underneath the shelf. 2. Place the objects underneath the net and secure the net loops to the retainers underneath the shelf. All objects loaded on the cargo shelf MUST BE SECURED UNDER THE CARGO NET .
SEA TING Adjustable head restraints Y our vehicle’ s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision.
Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’ s safety belt in the event of a collision. Lift handle to move seat forward or backward.
Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’ s safety belt in the event of a collision. Move the control up or down to move the seat up and down.
The lumbar control is located on the inboard side of the driver’ s seat. Move the control up or down to adjust lumbar support. Memory seats and mirrors (if equipped) The memory seat control is located on the driver’ s door panel.
2. Press and hold the desired memory position button. W ithin ten seconds, press the unlock button on the transmitter while the memory button is pressed. 3. When the transmitter has been programmed, the indicator will flash five times. The indicator light will remain illuminated until the memory button is pressed again or ten seconds lapse.
• 4 passenger vehicle (with third row seat in storage position) A. Cargo mat B. Narrow mats C. Sliding door mats, LH/RH • 5 passenger vehicle (second row seats removed) A.
• 5 passenger vehicle (second row seats removed and third row bench seat moved forward to limousine seating position) A. Cargo mat B. Narrow mats • T wo passenger vehicle (second row seats removed and third row seat stored in full forward position) A.
• Bucket seat (driver’ s side only) - inboard side of seat base Use only soft cups in the cupholder . Hard objects can injure you in a collision. Adjusting 2nd row bench Pull control up to flip seatback to forward flat position.
2nd row bucket seats (if equipped) • Adjusting the left side bucket seat Pull control up to recline the seatback or fold the seatback flat. • Adjusting the right side (E-Z Entry T ip Slide) bucket seat The E-Z Entry T ip Slide seat allows for easier entry and exit to and from the 3rd row seat.
T o exit the third row seat, pull up on the 3rd row access control. T o return the seat to a seating position, move the seat rearward until the seat track locks.
Pull control up to flip seatback to a forward flat position. Adjusting 3rd row bench Pull control up to adjust seatback position. This control will also allow the seatback to be put in the forward flat position.
The entire seat can be moved to four seating positions and two storage positions. Before rearranging the seats, remove any floor mats that might be in the way , see Removable floor mats in this chapter for instructions on placement of floor mats.
T o move the seat to another seating or storage position: 1. Lift control (A) to release the seat cushion and flip the cushion up. The seat cushion must be moved to the storage position before the seat can be moved along the track. 2. Pull control (B) to move the seat forward or backward until it locks into position.
After sliding the seat, check to ensure that both sides of the seat are locked in position. This must be done before the vehicle is put into motion in order to prevent unintended movement of the seat. Every time you adjust any seat, check to be sure that it is properly latched in the lock position of both seat tracks.
T o install the seat: The bucket seats are not interchangeable due to the locations of the seat anchors on the floor of the vehicle. Each seat must be installed in its original position.
It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
2. T o unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts.
How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Front safety belt height adjustment Y our vehicle has safety belt height adjustments for the driver and front passenger . Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o lower the shoulder belt height, push the button and slide the height adjuster down.
Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). T o lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. T o tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips.
Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates until safety belt is buckled. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding.
AIR BAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
National Highway T raffic Safety Administration (NHTSA) recommends a minimum distance of at least 25 cm (ten [10] inches) between an occupant’ s chest and the driver air bag module. Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries.
Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.
The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors.
Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use.
SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’ s instructions with the safety seat you put in your vehicle.
Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps.
2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Installing child safety seats in the lap belt seating positions 1. Lengthen the lap belt. T o lengthen the belt, hold the tongue so that its bottom is perpendicular to the direction of webbing while sliding the tongue up the webbing. 2. Place the child safety seat in the center seating position.
Seat T ype/Position T ether to... Reference Section 3-passenger/3rd row position Floor anchor directly behind child seat position 3rd row seats 2-passenger bench or bucket/2nd row child seat position .
Second row seats 1. Position the child safety seat on the passenger seat cushion. 2. Route the child safety seat tether strap over the back of the seat.
4. Rotate the tether strap. 5. Clip the tether strap to the seat tether slot bracket at the lower rear portion of the seatback. If the tether strap is clipped incorrectly (as shown) the child safety seat may not be retained properly in the event of a collision.
6. Rotate the tether strap clip. 7. Refer to the instructions in this section under Installing child safety seats in combination lap and shoulder belt seating positions to secure the child safety seat. 8. T ighten the child safety seat tether strap according to the manufacturer’ s instructions.
Third row seat and tether anchorage hardware The tether has to be attached to the anchorage locations on the floor behind the third row seating position (third row seat only) with a tether anchorage hardware kit.
Third row bench in second row position T o attach a tether strap to a lap/shoulder belt: 1. Route the tether strap under the head restraint and between the head restraint supports. 2. Hook the tether strap hook into the large hole at the end of the seat belt tongue of the lap/shoulder belt directly behind the child seat position.
BUIL T -IN CHILD SEA TS Built-in child safety seat (if equipped) The 2nd row seat may include a built-in child seat. This child seat conforms to all Federal and local motor vehicle safety standards. Read the labels located on the child seat cushion for information on the built-in child seat.
1. Pull the release strap near the bottom of the seatback. 2. Grasp the child seat at the top of the seatback and pull the top forward to release the latch.
4. Read all information and warnings on the child seat cushion and shoulder safety belt. The child seat is to be used only by children who: • are at least one year old • weigh between 10 and 27 kg (22 and 60 lbs.) • shoulders must be below the shoulder harness slots 5.
10. Pull the right shoulder belt fully out to put the retractor into the automatic locking mode. 11. If the belts become too tight, unbuckle the crotch safety belt buckle to unlock the retractors, then reinsert both belt tongues. Removing your child from the built-in child seat 1.
PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the parking brake is set. 4. Make sure the gearshift is in P (Park). 5. T urn the key to 3 (ON) without turning the key to 4 (ST ART). If there is difficulty in turning the key , firmly rotate the steering wheel left and right until the key turns freely .
Make sure the corresponding lights illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light may not illuminate. ST ARTING THE ENGINE 1. T urn the key to 4 (ST ART) without pressing the accelerator pedal and release as soon as the engine starts.
Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater -defroster system to respond quickly . Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below .
Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning to bring in fresh air . Improve vehicle ventilation by keeping all air inlet vents clear of snow , leaves and other debris.
BRAKES Y our service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system.
ABS warning lamp The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced.
The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park).
• high crown in center of road • high crosswinds • wheels out of alignment • loose or worn components in steering linkage AUTOMATIC TRANSAXLE OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) unless the brake pedal is depressed.
Understanding gearshift positions T o account for customer driving habits and conditions, your automatic transaxle electronically controls the shift feel by using an adaptive learning strategy . During the first few hundred kilometers (miles) of operation, it is normal for your transaxle to have abrupt shifts.
automatic overdrive transaxle. When your vehicle cruises at a constant speed for any length of time, this fourth gear will increase your fuel economy .
second and third gears and will not shift into fourth gear . Operating in D (O/D OFF) provides more engine braking than Overdrive for descending hills or city driving. T o return the transaxle to the normal Overdrive operation, press the O/D OFF control again.
Driving with an automatic overdrive transaxle Y our automatic transaxle electronically controls the shift feel by using an adaptive learning strategy .
V EHICLE LOADING Before loading a vehicle, familiarize yourself with the following terms: • Base Curb W eight : W eight of the vehicle including any standard equipment, fluids, lubricants, etc. It does not include passengers or aftermarket equipment.
Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’ s GVWR and GA WR limitations. Replacement tires with a higher limit than the originals do not increase the GVWR and GA WR limitations.
The optional T railer T ow Prep Package is recommended for towing of any trailer since it provides a heavy duty battery , conventional size spare tire and wiring. T railer towing puts additional loads on your vehicle’ s engine, transmission, axle, brakes, tires, and suspension.
Preparing to tow Use the proper equipment for towing a trailer , and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance.
Trailer lamps T railer lamps are required on most towed vehicles. Make sure your trailer lamps conform to local and Federal regulations. See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps. Driving while you tow Do not drive faster than 88 km/h (55 mph) when towing a trailer .
LUGGAGE RACK The front and rear crossbar can be adjusted to fit the item being carried. Do not load more than 44 kg (100 lbs.) on the luggage rack. T o adjust cross-bar position: 1. Loosen the thumbwheel at both ends of the cross-bar . 2. Slide the cross-bar to the desired location.
HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger , etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on the instrument panel. • Depress hazard lights control to activate all hazard flashers simultaneously .
The fuel pump shut-off switch is located in the driver’ s foot well, behind the kick panel. The reset button for the fuel pump shut-off switch is accessible through an opening in the kick panel. Use the following procedure to reset the fuel pump shut-off switch.
Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses Cartridge Maxi Fuses Fuse Link Cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.
The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Description Corner Lamps 10A Front Exterior Lamps — — Not Used I/P Illum 7.5A Interior Panel Illumination Lamps Electron 10A T r.
Fuse/Relay Location Fuse Amp Rating Description Room Lamp 15A Interior Lamps Mirror 7.5A Smart Entry Control (SEC), Power Mirror Switch Stop Lamp 20A Brake Pedal Position (BPP) Switch, T railer T ow C.
Fuse/Relay Location Fuse Amp Rating Description Electron 10A T ransmission Control, Lighting Control Module, ABS Control Module, Smart Entry Control (SEC)/T imer Module Rear Defog 20A Rear W indow Def.
The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Description — — Not Used FUEL PUMP 15A* Fuel Pump Relay INJ 10A* Powertrain Control Module (PCM), Injectors SEC 7.5A* Anti-Theft Relay , Smart Entry Control (SEC)/T imer Module RAD 7.
Fuse/Relay Location Fuse Amp Rating Description ABS 20A* ABS Control Module — — Not Used H/L RH 15A* Lighting Control Module HORN 15A* Horn Relay — — Not Used H/L LH 15A* Lighting Control Modu.
Relay box The relay box is located in the engine compartment in front of the battery . The relays are coded as follows: Relay location Description 1 Start Inhibit Relay 2 Fuel Pump Relay 3 Bulb Check .
T emporary spare tire information Y our vehicle may have a temporary or conventional size spare tire. The temporary spare tire for your vehicle is labeled as such. It is smaller than a regular tire and is designed for emergency use only . Replace this tire with a full-size tire as soon as possible.
Removing the spare tire 1. Open the liftgate, locate the U-shaped slits in the carpet, and flip up the piece of carpet to expose the hex nut. 2. Insert the lug nut wrench on the hex nut in cargo floor . 3. T urn the wrench counterclockwise until tire is lowered to the ground and the cable is slightly slack.
Stowing the spare 1. Lay the tire on the ground with the interior side facing up. 2. Install the retainer through the wheel center and slide the wheel under the vehicle. 3. T urn the wrench clockwise until the tire is raised to its original position underneath the vehicle.
1. Park on a level surface, activate hazard flashers and set parking brake. 2. Place gearshift lever in P (Park), turn engine OFF , and block the diagonally opposite wheel. 3. Remove the spare tire and jack assembly . 4. Remove the center ornament or wheel cover from the wheel with the tapered end of the jack handle that came with your vehicle.
Jacking notches are located approximately six inches rearward of the front wheels and twelve inches foward of the rear wheels. 6. Locate the jack notch closest to the tire you are changing, then place the jack on the frame rail directly behind the notch.
JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. Y ou could damage the catalytic converter . Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted.
Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery .
3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system.
Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member , your roadside assistance center . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt.
SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a Scheduled Maintenance Guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide necessary parts and service.
Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.3L V6 engine 1. Power distribution box 2. Brake fluid reservoir 3. Air filter assembly 4. Battery 5. Relay box 6. Engine oil filler cap 7. Engine oil dipstick 8. W indshield washer fluid reservoir 9. Engine coolant reservoir 10.
ENGINE OIL Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervals for checking the engine oil . 1. Make sure the vehicle is on level ground. 2. T urn the engine off and wait a few minutes for the oil to drain into the oil pan.
• If the oil level is below the L mark, add enough oil to raise the level within the L and H range. • Oil levels above the H mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated.
Engine oil and filter recommendations Look for this Certification T rademark. Use SAE 5W -30 motor oil certified for gasoline engines by the American Petroleum Institute (API). Motor oil displaying the API Certification T rademark will meet all requirements for your vehicle’ s engine.
BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the Scheduled Maintenance Guide for the service interval schedules: 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir .
WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low , add enough fluid to fill the reservoir . In very cold weather , do not fill the reservoir all the way .
The engine coolant must be maintained at the correct fluid level and concentration to work properly . If the engine coolant fluid level and concentration is not maintained correctly , damage to the engine and cooling system may result . When the engine is cold, check the level of the engine coolant in the reservoir .
• DO NOT USE alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze. • DO NOT USE supplemental coolant additives in your vehicle. These additives may harm your engine’ s cooling system. • DO NOT MIX recycled coolant and conventional coolant together in your vehicle.
T o avoid scalding hot steam or coolant from being released from the engine cooling system, never remove the radiator cap while the engine is running or hot. Failure to follow this warning may result in damage to the engine’ s cooling system and possible severe personal injury .
• NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage.
properly , i.e., if the transaxle slips or shifts slowly or if you notice some sign of fluid leakage. Automatic transmission fluid expands when warmed. T o obtain an accurate fluid check, drive the vehicle until it is warmed up (approximately 30 km [20 miles]).
High fluid level Fluid levels above the safe range may result in transaxle failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition.
CHANGING THE AIR FILTER ELEMENT 1. Release the four clamps that secure the air filter housing cover . 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the air filter housing. 4. Install a new air filter element.
If the electrolyte level in the battery is low , you can add plain tap water to the battery , as long as you do not use hard water (water with a high mineral or alkali content). If possible, however , try to only fill the battery cells with distilled water .
transaxle must relearn its adaptive strategy . Optimal shifting will resume within a few hundred kilometers (miles) of operation. If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected.
The odor and particulate air filtration system is designed to reduce the concentration of objectionable exterior odors as well as airborne particles such as dust, spores and pollen in the air being supplied to the interior of the vehicle.
2. Remove the six (6) screws (B) from the cowl grille (A) at the base of the windshield. 3. Open the hood. 4. Remove the four (4) plastic screws (C) from the forward edge of the cowl leaf screen under the hood. • Remove the four (4) screw anchors by pushing upward on the screw anchor .
8. Remove four (4) screws from the top surface of the cabin air filter top cover . 9. Remove the cover . 10. Remove the filter element by pulling forward on the top surface of the filter and lifting. 11. Install the new filter (A) element into the filter retaining frame (B).
14. Position the cowl grille in place. 15. Reinstall the four (4) screw anchors and the four (4) plastic screws. 16. Close the hood. 17. Reinstall the six (6) screws in the cowl grille. 18. Reinstall the wiper arms. Ensure that you reinstall the wiper arms in the same position.
INFORMA TION ABOUT TIRE QUALITY GRADES New vehicles are fitted with tires that have their T ire Quality Grade (described below) molded into the tire’ s sidewall. These T ire Quality Grades are determined by standards that the United States Department of T ransportation has set.
T emperature A B C The temperature grades are A (the highest), B, and C, representing the tire’ s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
• Four tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label.
Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over . T ires that are larger or smaller than your vehicle’ s original tires may also affect the accuracy of your speedometer .
The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
• A void getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury . • Fuels can also be harmful if absorbed through the skin.
When the fuel filler door is open, the left hand sliding door will not open. When fueling your vehicle: 1. T urn the engine off. 2. Carefully turn the fuel filler cap counterclockwise, using caution to minimize the possibility of fuel spraying. 3. Remove the cap from the fuel filler pipe.
Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with an (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas.
If you have run out of fuel: • Y ou may need to crank the engine several times after refueling before the system starts to pump the fuel from the tank to the engine. • Y our “Service Engine Soon” indicator may come on. For more information on the “Service Engine Soon” indicator , refer to the Instrumentation chapter .
For consistent results when filling the fuel tank: • Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow three automatic click-offs when filling. • Always use fuel with the recommended octane rating.
Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy . • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop.
• Carrying unnecessary weight may reduce fuel economy (approximately 0.4 km/L [1 mpg] is lost for every 180 kg [400 lb] of weight carried). • Adding certain accessories to your vehicle (for example bug deflectors, rollover/light bars, running boards, ski/luggage racks) may reduce fuel economy .
The scheduled maintenance items listed in the Scheduled Maintenance Guide are essential to the life and performance of your vehicle and to its emissions system.
condition. T o ready the on-board diagnostics system for I/M testing, follow the procedure described below: 1. Allow the engine to cool to ambient temperature (the engine coolant temperature gauge indicator will point to C).
Do not remove lamp bulbs unless they will be replaced immediately . If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance. Replacing headlamp bulbs T o remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then open the hood.
2. Install the bulb retaining ring over the plastic base until it contacts the rear of the socket by rotating clockwise until you feel a “stop.” 3. Connect the electrical connector into the rear of the plastic base until it snaps, locking it into position.
Replacing high-mount brakelamp bulbs 1. Remove the two screws and lamp assembly from vehicle. 2. Remove the bulb by rotating socket counterclockwise and pulling it out of the lamp assembly . 3. Pull bulb straight out of socket and push in the new bulb.
Replacing license plate lamp bulbs 1. Remove two screws, grommets and the license plate lamp assembly from the liftgate. 2. Remove bulb socket by turning counterclockwise.
Function Number of bulbs T rade number Stepwell lamps 4 194 Glove compartment 1 194 All replacement bulbs are clear in color except where noted. T o replace all instrument panel lights - see your dealer .
Remove any exterior accessories, such as antennas, before entering a car wash. If you have wax applied to the vehicle at a commercial car wash, it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield.
Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • T ake care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage.
Cleaning the exterior lamps W ash with the same detergent as the exterior of your vehicle. If necessary , use a tar remover such as Ford Extra Strength T ar and Road Oil Remover (B7A-19520–AA) or tar remover if necessary . T o avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners.
Cleaning the built-in child seat (if equipped) Clean with mild soap and water . Do not use household cleaning products because they may weaken the safety belt webbing or damage the vinyl parts of the seat. The child seat liner is removable and may be machine-washed and air dried.
MOTORCRAFT PART NUMBERS Component 3.3L V6 engine Engine air filter element F A-1121 Cabin air filter FP-27 Fuel filter FG-993 Battery (standard) BXT -35 Battery 1 BXT -24F Oil filter FL-2007 PCV V alve EV -217 Spark plugs 2 AGSP-32FP 1 Standard for Canada.
LUBRICANT SPECIFICATIONS Item Ford part name Ford part number Ford specification Brake fluid High Performance DOT 3 Motor V ehicle Brake Fluid C6AZ-19542-AB ESA-M6C25-A and DOT 3 Door weatherstrips Si.
Item Ford part name Ford part number Ford specification Disc brake caliper rails Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft W A-10) ESE-M1C171-A Constant velocity joints CV Joint Grease (High T emp.
VEHICLE DIMENSIONS V ehicle dimensions mm (in) (1) Overall length 4 945.4 (194.7) (2) Overall width 1 902.5 (74.9) (3) Overall height (with luggage rack) 1 780.5 (70.1) (4) Wheelbase 2 849.9 (112.2) (5) T rack - Front 1 610.4 (63.4) (5) T rack - Rear 1 610.
IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’ s side.
V ehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel and under the liftgate scuff plate at the bottom of the liftgate opening. (Please note that in the graphic XXXX is representative of your vehicle identification number .
GETTING ROADSIDE ASSIST ANCE T o fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty .
Ford Extended Service Plan Y ou can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.
Getting the service you need At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. When you need warranty repairs your selling dealer would like you to return to it for that service, but you may also take your vehicle to another Ford Motor Company dealership authorized for warranty repairs.
If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Assistance Center to find an authorized dealership to help you.
THE DISPUTE SETTLEMENT BOARD (U.S. only) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states.
Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln-Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm.
Y ou will receive a letter of explanation if your application does not qualify for Board review . Oral presentations If you would like to make an oral presentation, indicate YES to question #6 on the application.
GETTING ASSIST ANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country , contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel.
Ford Custom Silicone Gloss Polish Ford Custom Vinyl Protectant* Ford Deluxe Leather and Vinyl Cleaner Ford Extra Strength T ar and Road Oil Remover* Ford Extra Strength Upholstery Cleaner Ford Metal S.
Comfort and convenience Air conditioner Air filtration systems Cargo nets Cargo organizers Cargo shades Cargo trays Dash trim Engine block heaters Gear shift knob Luggage presenter (Continental only) .
Soft luggage cover Speed control T owing mirrors T railer hitch T railer hitch bars and balls T railer hitch wiring adaptor Protection and appearance equipment Air bag anti-theft locks Bed mat/bedline.
T ailgate lock T ailgate protector T onneau covers T ouch-up paint Universal floor mats For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to .
ORDERING ADDITIONAL OWNER’S LITERA TURE T o order the publications in this portfolio in the United States: Make checks payable to: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.
REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
Accessory delay .......................... 90 Air bag supplemental restraint system ........................................ 131 and child safety seats ............ 133 description .............................. 131 disposal ..........................
Ford accessories for your vehicle ..................................... 248 Ford Extended Service Plan .......................................... 242 Getting assistance outside the U.S. and Canada ..................... 248 Getting roadside assistance .
GVWR (Gross V ehicle W eight Rating) ....................................... 165 calculating ............................... 165 definition ................................. 165 driving with a heavy load ...... 165 location ...........................
Overdrive ..............................87,164 Panic alarm feature, remote entry system .............................. 101 Parking brake ............................ 158 Parts (see Motorcraft parts) ....235 Power distribution box (see Fuses) .........
W arning chimes ...................... 10,11 W arning lights (see Lights) ......... 6 W asher fluid ..............................198 W ater , Driving through ............. 164 W indows power ......................................... 89 rear wiper/washer .
260.
261.
262.
263.
Item Information Required fuel Unleaded fuel only - 87 octane Fuel tank capacity 75.7L (20.0 gallons) Engine oil capacity (includes filter change) 4.0L (4.2 quarts). Use Motorcraft SAE 5W -30 Super Premium Motor Oil, Ford specification WSS-M2C153-G. T ire size and pressure Refer to the Certification Label on inside of driver’ s door .
デバイスMercury 1999 Villagerの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Mercury 1999 Villagerをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMercury 1999 Villagerの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Mercury 1999 Villagerの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Mercury 1999 Villagerで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Mercury 1999 Villagerを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMercury 1999 Villagerの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Mercury 1999 Villagerに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMercury 1999 Villagerデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
