MercuryメーカーSR-10K Mag-Stripe Access Systemの使用説明書/サービス説明書
ページ先へ移動 of 19
Doc. 10107-0007 Rev 1.04 Page 1 Mercury Security Corporation, © 2005 SR-10K SR-10K Mag-Stripe Access System Users Guide.
Doc. 10107-0007 Rev 1.04 Page 2 Mercury Security Corporation, © 2005 SR-10K Table of Contents Section Page Overview 3 Quick S tart and Configuration Planning 5 Programming Guide 6 Operating Mode S pe.
Doc. 10107-0007 Rev 1.04 Page 3 Mercury Security Corporation, © 2005 SR-10K Description The SR-10K is a complete stand-alone access controller , using either magnetic-stripe cards or cipher (keypad) codes for identifying valid users. The Card Reader with Keypad and the Interface Module are the SR-10K system's major components.
Doc. 10107-0007 Rev 1.04 Page 4 Mercury Security Corporation, © 2005 SR-10K Cipher Codes The SR-10K supports up to 10 cipher codes. Each code is one to six digits in length - shorter codes are terminated with the '#' key .
Doc. 10107-0007 Rev 1.04 Page 5 Mercury Security Corporation, © 2005 SR-10K Quick Start The factory default setting enables the SR-10K to be used immediately , without any further programming, using the 10 cards shipped with the unit. The database is set to Random Mode, and the cards are enrolled as Level 1 users in slots 01 through 10.
Doc. 10107-0007 Rev 1.04 Page 6 Mercury Security Corporation, © 2005 SR-10K SR-10K Programming Guide The COMMAND ENTR Y MODE is selected by passing a valid MASTER card through the reader . The intergral keypad allows direct data entry on the SR-10K. The "*" key is used to start a new command entry .
Doc. 10107-0007 Rev 1.04 Page 7 Mercury Security Corporation, © 2005 SR-10K CIPHER CODES Related Commands (Commands 15 through 17) Up to 10 cipher codes may be defined (user slots 0 through 9). Each cipher code may be from 1 to 6 digits long. Cipher codes shorter than 6 digit s are terminated with the "#" key .
Doc. 10107-0007 Rev 1.04 Page 8 Mercury Security Corporation, © 2005 SR-10K Command 33 - Set the Auxiliary Relay Pulse Time (Output K2) *3 3 - select Command 33 0-9 0-9 - select the pulse time for Ou.
Doc. 10107-0007 Rev 1.04 Page 9 Mercury Security Corporation, © 2005 SR-10K Command 91 - Set a New MASTER Card *9 1 - select Command 91 1 or 2 - select which Master Card to change: 1 or 2 new card - .
Doc. 10107-0007 Rev 1.04 Page 10 Mercury Security Corporation, © 2005 SR-10K Description Access Control with Door Monitoring provides for basic access control and door use annunciation. A downward read of all valid User Cards pulse Output K1, the strike control relay.
Doc. 10107-0007 Rev 1.04 Page 11 Mercury Security Corporation, © 2005 SR-10K Description Restricted Access Control with Door Monitoring restricts Level 1 user access based on the status of Input I2 and provides door use annunciation on Output K2. Level 1 cards are accepted only if the Input I2 sees a closed contact.
Doc. 10107-0007 Rev 1.04 Page 12 Mercury Security Corporation, © 2005 SR-10K Operating Mode 03: Access Control and Alarm Panel Control Description The Access Control and Alarm Panel Control configuration provides for basic access control and gives some users the ability to send a pulse to arm and disarm alarm panels.
Doc. 10107-0007 Rev 1.04 Page 13 Mercury Security Corporation, © 2005 SR-10K Operating Mode 04: Restricted Access Control and Alarm Panel Control Description Restricted Access Control and Alarm Panel Control provides restricts Level 1 user access based on the status of Input I2 and it gives some users the ability to arm/disarm alarm panels.
Doc. 10107-0007 Rev 1.04 Page 14 Mercury Security Corporation, © 2005 SR-10K Operating Mode 05: "Supervisor" Restricted Access Control Description This mode allows Level 2 cards to toggle Output K2, which, connected back to Input I2, restricts Level 1 users.
Doc. 10107-0007 Rev 1.04 Page 15 Mercury Security Corporation, © 2005 SR-10K Description Access Control with Door Bell Control operates just like Mode 1, with an additional feature for using Output K2 for annunciation. This mode was created for applications where Output K2 is configured to drive a door bell/ buzzer.
Doc. 10107-0007 Rev 1.04 Page 16 Mercury Security Corporation, © 2005 SR-10K +− Installation Find a suitable location to anchor the reader mounting bracket. The mounting of the reader does not require a junction box. However, rigid conduit is required for outdoor application.
Doc. 10107-0007 Rev 1.04 Page 17 Mercury Security Corporation, © 2005 SR-10K Maintenance The SR-10K readers are designed to provide continuous service with minimal routine maintenance. However, contaminants (such as magnetic oxides from badges and dirt) tend to accumulate on the read head.
Doc. 10107-0007 Rev 1.04 Page 18 Mercury Security Corporation, © 2005 SR-10K 1.4 [36] 2.9 [74] 3.25 [83] 2 X Ø0.1 8 [4.5] HOLES 2.0 [50] 5.5 [140] 1.3 [33] 3.3 [84] 2.6 [66 ] Reader and Interface Dimensions Reader to Interface Connection: Connect the Reader to the Interface Module using the straight 6-conductor modular cable.
Doc. 10107-0007 Rev 1.04 Page 19 Mercury Security Corporation, © 2005 SR-10K Addendum - Revision C This revision changed the door module to accommodate screw mounting instead of using snap track.
デバイスMercury SR-10K Mag-Stripe Access Systemの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Mercury SR-10K Mag-Stripe Access Systemをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMercury SR-10K Mag-Stripe Access Systemの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Mercury SR-10K Mag-Stripe Access Systemの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Mercury SR-10K Mag-Stripe Access Systemで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Mercury SR-10K Mag-Stripe Access Systemを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMercury SR-10K Mag-Stripe Access Systemの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Mercury SR-10K Mag-Stripe Access Systemに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMercury SR-10K Mag-Stripe Access Systemデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
