MGE UPS SystemsメーカーPulsar EX 1500の使用説明書/サービス説明書
ページ先へ移動 of 28
51031604EN/AA - Page 1 Installation and user manual Pulsar EX 700 / 1000 / 1500 e-mail: info@direktronik.se tel: 08-52 400 700 fax: 08-520 18121.
Page 2 - 51031604EN/AA Introduction Thank you for selecting an MGE UPS SYSTEMS product to protect your electrical equipment. The Pulsar EX range has been designed with the utmost care. We recommend that you take the time to read this manual to take full advantage of the many features of your UPS.
51031604EN/AA - Page 3 Safety Safety of persons Safety rules A UPS has its own internal power source (the battery). Consequently, the power outlets may be energised even if the UPS is disconnected from the AC-power source. Dangerous voltage levels are present within the UPS.
Page 4 - 51031604EN/AA Foreword Using this document Important instructions that must always be followed. Information, advice, help. Visual indication. Action. Audio indication. In the illustrations on the following pages, the symbols below are used: LED off.
51031604EN/AA - Page 5 Contents 1. Presentation 1.1 Pulsar EX range ............................................................................................................. ............. 7 T ower model ............................................
Page 6 - 51031604EN/AA Contents 3.4 Personalisation (optional) ........................................................................................................... 19 Function ....................................................................
51031604EN/AA - Page 7 1. Presentation 1.1 Pulsar EX range Tower model Rack model EX 700 / EX 1000 EX 1500 EX 700 EX 1000 EX 1500 Dimensions in mm (H x W x D) 235.5 x 145 x 400 235.5 x 145 x 505 Weight in kg 10 12 15 EX 700 Rack EX 1000 Rack EX 1500 Rack EX 700 Rack EX 1000 Rack EX 1500 Rack Dimensions in mm (H x W x D) 88 (2U) x 482.
Page 8 - 51031604EN/AA 1 2 RS232 USB 1 2 RS232 USB 5 1. Presentation 1.2 Back Pulsar EX 1500 Pulsar EX 700 / Pulsar EX 1000 slot for communications-card option. RS232 communications port. USB communications port. four outlets for direct connection of protected equipment.
51031604EN/AA - Page 9 1 2 RS232 USB 1. Presentation Pulsar EX 700 Rack / Pulsar EX 1000 Rack / Pulsar EX 1500 Rack 7 6 1 4 11 8 3 9 10 Rack model slot for communications-card option. RS232 communications port. USB communications port. four outlets for direct connection of protected equipment.
Page 10 - 51031604EN/AA 100% 80% 50% 20% test % % 1 2 by-pass 1.3 Control panel Alarms UPS overload. electronics fault. battery fault. hold down to display percent load: - lamp test or buzzer OFF. - forced transfer to bypass and back by pressing button 3 times in less than 5 seconds.
51031604EN/AA - Page 11 2. Installation 2.1 Unpacking and checks two cords for connection of the protected equipment. RS 232 communications cable. USB communications cable. "UPS Driver" diskette for UPS personalisation. "Solution Pac" CD ROM.
Page 12 - 51031604EN/AA 2. Installation 27 28 30 24 Rack model 24 29 EX1000 Rack ␣ 24 two cords for connection of the protected equipment. ␣ 25 RS 232 communications cable. ␣ 26 USB communications cable. ␣ 27 "UPS Driver" diskette for UPS personalisation.
51031604EN/AA - Page 13 2.2 Installation of the rack version 2. Installation Rack mounting diagram with rails. The rails and the necessary mounting hardware are supplied by MGE UPS SYSTEMS.
Page 14 - 51031604EN/AA 2. Installation 2.3 Connection to the RS 232 or USB communications port (optional) 1 - Connect the RS 232 25 or USB 26 communications cable to the serial port or the USB port on the computer. 2 - Connect the other end of the communications cable 25 or 26 to the RS 232 2 or USB 3 communications port on the UPS.
51031604EN/AA - Page 15 1 2 U-Talk USB 2.4 Installation of the communications-card option It is not necessary to shut down the UPS to install the communications card: 1 - Remove the slot 1 cover secured by two screws. 2 - Insert the card in the slot. 3 - Secure the card with the two screws.
Page 16 - 51031604EN/AA 1 2 ? p r e s s r e s e t 24 7 4 11 2. Installation 2.5 Connections Check that the indications on the rating plate on the back of the UPS correspond to your AC-power system and to the actual electrical consumption of all the equipment to be connected to the UPS.
51031604EN/AA - Page 17 100% 80% 50% 20% test % % 1 2 by-pass The protected equipment connected to the UPS can be energised, whether AC input power is available or not. 3. Operation 3.1 Start-up 12 13 14 23 Press the ON / OFF button 23 . The buzzer beeps and all the LEDs go ON.
Page 18 - 51031604EN/AA test % 1 2 by-pass 1 2 by-pass 1 2 by-pass 3. Operation 3.3 Operation on battery power (following failur e of AC input power) 22 Transfer to battery power The AC-power source is outside tolerances, LED 23 is ON, the buzzer beeps three times.
51031604EN/AA - Page 19 3. Operation 3.4 Personalisation (optional) Function Personalisable function Automatic start Cold start (battery power) Forced shutdown Sleep mode UPS ON / OFF via software Def.
Page 20 - 51031604EN/AA 3. Operation Personalisable function Rated UPS voltage Rated UPS frequency UPS tolerance for AC-power source frequency Overload alarm threshold UPS restart following short-circ.
51031604EN/AA - Page 21 Troubleshooting requiring MGE UPS SYSTEMS after-sales support 4. Maintenance 4.1 T roubleshooting Indication LED 13 flashes and the buzzer sounds continuously. Signification UPS electronics have detected a UPS fault. Depending on the UPS personalisation parameters (see section 3.
Page 22 - 51031604EN/AA F G C D E A B 4.2 Replacement of the battery module 4. Maintenance Removal of battery module A - Press to open door. B - Slide the door open and remove it. C D E - Procedure to remove the protective cover. F - Disconnect the battery module.
51031604EN/AA - Page 23 E F C D 4. Maintenance B A Rack model Removal of battery module A - Remove the two screws securing the door. B - Slide the door open and remove it. C - Unscrew the bar that holds the battery module in place. D - Remove the bar.
Page 24 - 51031604EN/AA 5. Environment This product has been designed to respect the environment: It does not contain CFCs or HCFCs. UPS recycling at the end of service life: MGE UPS SYSTEMS undertake.
51031604EN/AA - Page 25 6. Appendices 6.1 T echnical characteristics Operating conditions Relative humidity: 20 to 90% without condensation. Temperature: 0 to 40 ° C.
Page 26 - 51031604EN/AA 6. Appendices 6.2 Glossary Authorised voltage range for Upper and lower voltage thresholds within which the UPS can operate on the automatic transfer to bypass if fault or bypass in the event of a UPS fault or overload.
51031604EN/AA - Page 27 6. Appendices 6.3 Index A AC power Failure .................................................................... 18 Frequency tolerance ............................................... 20 Return ..................................
Page 28 - 51031604EN/AA.
デバイスMGE UPS Systems Pulsar EX 1500の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
MGE UPS Systems Pulsar EX 1500をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMGE UPS Systems Pulsar EX 1500の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。MGE UPS Systems Pulsar EX 1500の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。MGE UPS Systems Pulsar EX 1500で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
MGE UPS Systems Pulsar EX 1500を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMGE UPS Systems Pulsar EX 1500の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、MGE UPS Systems Pulsar EX 1500に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMGE UPS Systems Pulsar EX 1500デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。