MicrosoftメーカーSHG-TCの使用説明書/サービス説明書
ページ先へ移動 of 16
SHG-A* Absolute, SHG-TC, SHG-TS & SHG-VS Linear Encoders NEWALL MEASUREMENT SYSTEMS LTD N Installation Manual THIS MANUAL SHOULD BE USED IN CONJUNCTION WITH WITH THE CORRESPONDING PROTOCOL DOCUMEN.
Newall Measurement Systems Contents 1 CONTENTS 1.0 Technical Specification ..............................................1 1.1 Bracketry ..............................................................................2 1.2 Preparation ..................
Introduction Newall Measurement Systems 2 1.0 INTRODUCTION This manual will provide connection and mounting instructions for Newall's Absolute, Digital and Distance Coded linear encoders. It is important that you read and understand this manual prior to commencing the hardware installation.
Figure 3.1 - Alignment of the reader head 2.0 ENCODER ASSEMBLY Item Description 1 Reader Head 2 Scale 3 Scale Support Link 4 Scale Anchor Pin 5 Support Pillar Short Item Description 6 Support Pillar Long 7 Scale Cover 8 M5 Nut 9 M8 x Socket Button Head Newall Measurement Systems 3 Encoder Assembly / Mounting the Reader Head 3.
Mounting the Scale Newall Measurement Systems 4 4.0 MOUNTING THE SCALE 4.1 Double End Mounting Note: Refer to section 4.3 for mounting scales in excess of 2.5 metres. Each end of the scale is different and can be identified by the “calibration adjustment end” and the “fixed end.
Mounting the Scale A maximum of two support pillars may be screwed together to allow for sufficient adjustment of the scale. If two pillars are insufficient to enable the scale to be mounted, then additional brackets will be necessary. These brackets must be sufficiently rigid to eliminate any axial movement of the scale.
Mounting the Scale Newall Measurement Systems 6 Remove the link/pin assembly and the scale from the reader head. Drill and tap M8 x 18mm deep (USA 5/16" -18 x 3/4" deep) into the machine casting as marked by the transfer punch. Fit the pillar(s) to the machine casting by using one of the methods shown in Figure 4.
Mounting the Scale 4.3 Scales in Excess of 2.5 Meters Traverse the machine to fullest extent of travel including hand winding past any electrical limits or trip dogs. Insert the set up tube into the reader head, allowing for a sufficient amount of scale to project from the reader head in order to fit the scale mounting brackets.
Newall Measurement Systems 8 Mounting the Scale For scales which are mounted in the horizontal position, spring loaded scale supports are included and should be positioned according to Table 1. Once the locations for the supports have been determined, the reader head should be positioned in the location where the first support is to be fitted.
Mounting the Scale / Fitting the Scale Guard Length 2500mm 3000mm 3500mm 4000mm 4500mm 5000mm 5500mm 6000mm 6500mm 7000mm 7500mm 8000mm 8500mm 9000mm 9500mm 10000mm 10500mm 11000mm No.
Newall Measurement Systems 10 Cable Routing / Final Check 6.0 CABLE ROUTING The most important and the most over looked aspect of fitting the linear encoder is proper cable routing. Dangling and loose cables can be snagged or broken causing irreparable damage.
Appendix A Newall Measurement Systems 11 Appendix A - SCALE BRACKET MOUNTING OPTIONS Outboard scale support mounting Scale supports inverted.
Appendix B Newall Measurement Systems 12 Appendix B - DIMENSIONAL DRAWING.
Appendix B (cont’d) Newall Measurement Systems 13 Appendix B - DIMENSIONAL DRAWING.
Notes Newall Measurement Systems 14.
NEWALL MEASUREMENT SYSTEMS LTD 023-80620 /03 -UK . O ct 2006 HEAD OFFICE Newall Measurement Systems Ltd. Technology Gateway, Cornwall Road South Wigston Leicester LE18 4XH United Kingdom Telephone: +44 (0)116 264 2730 Facsimile: +44 (0)116 264 2731 Email: sales@newall.
デバイスMicrosoft SHG-TCの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Microsoft SHG-TCをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMicrosoft SHG-TCの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Microsoft SHG-TCの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Microsoft SHG-TCで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Microsoft SHG-TCを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMicrosoft SHG-TCの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Microsoft SHG-TCに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMicrosoft SHG-TCデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。