MicrotestメーカーMICROSCANNERの使用説明書/サービス説明書
ページ先へ移動 of 20
MICROSCANNER ENGLISH - 1 M ICRO SCANNER TM M ICRO SCANNER TM PRO User Guide ENGLISH Test Equipment Depot 99 Washington Street Melrose, MA 02176-6024 www.
MICROSCANNER ENGLISH - 2 Test Equipment Depot 99 Washington Street Melrose, MA 02176-6024 www.testequipmentdepot.com 800-517-8431 781-665-0780 FAX.
MICROSCANNER ENGLISH - 3 T able of Contents The Keypad .......................................................... 4 Operating Mode .................................................... 4 Calibration Mode ................................................
MICROSCANNER ENGLISH - 4 The Keypad When turned on, MICROSCANNER will flash the LCD power-up test and then resume the test mode that was last executed. MICROSCANNER will turn off automatically when no cable is detected and no key has been used for 10 minutes.
MICROSCANNER ENGLISH - 5 Setting the NVP percentage Once in Calibrate Mode, the default NVP (Nominal Velocity of Propagation) will be displayed followed by the overall cable length. The cable length is measured with the currently stored NVP . NVP is the measure of how fast a signal travels down a cable compared to the speed of light.
MICROSCANNER ENGLISH - 6 Changing Display from Meters to Feet During Calibration you will be able to switch the displayed length from meters to feet by simply pressing the MODE key . Press the ON/OFF key once the desired cable length or NVP is displayed to terminate 'Calibrate' mode and store the new calibration factor.
MICROSCANNER ENGLISH - 7 T echnical Support If you have technical questions, you may contact Microtest T echnical Support by phone, fax or e- mail. North America, Latin America, and Asia Pacific: 1-800-NET-FIXR (1-800-638-3497) (U.S. and Canada only) 1-800-419-8991 (F AX) (U.
MICROSCANNER ENGLISH - 8 MICROSCANNER TM TM TM TM TM T ests Wiremap The Wiremap function tests twisted-pair cabling for proper wiring. Y our cabling configuration is checked for shield continuity , opens, shorts, crossed pairs, split pairs, and reversed pairs.
MICROSCANNER ENGLISH - 9 10BaseT Cable Token Ring unshielded shielded (2 pair, 4 wires) (2 pair, 4 wires) Below are examples of wiring faults. The FAUL T indicator will be displayed and the numerical wire indicators will blink.
MICROSCANNER ENGLISH - 10 If the wire does not go to the far end, the numerical indicator for the open will be left blank. The word Open will be displayed.
MICROSCANNER ENGLISH - 11 Length The Length function measures the full length of a twisted pair or coaxial cable. T wisted pair: If you are measuring standard pair length, MICROSCANNER will determine whether the cable is open, shorted, or connected to a hub.
MICROSCANNER ENGLISH - 12 Some early model 100TX only network equipment does not generate link pulses and MICROSCANNER will display HUB , the cable length and the word SIGNAL .
MICROSCANNER ENGLISH - 13 activate the blinking Hub light. The word SIGNAL blinks once every two seconds right below the word Hub . Go to the wiring closet to view a light that blinks once every two seconds at the port to which the cable is connected.
MICROSCANNER ENGLISH - 14 3. When MICROSCANNER displays PC and the cable length, press the MODE key to activate the blinking Hub light. Pair Length If ▲▼ are displayed, you will be able to show detailed pair information for each standard conductor pair .
MICROSCANNER ENGLISH - 15 Coaxial Cabling ( MICROSCANNER PRO ) Note: This feature is available in the residential version or when using the COAX upgrade kit. MICROSCANNER measures the full length of a 50 and/or 75 Ω (Ohms) coaxial cable, e.g. RG-6 and identifies its termination state.
MICROSCANNER ENGLISH - 16 Office Identifier The Office Identifier function allows you to find the termination of an office cable drop from a wiring closet. By inserting the Office Identifier adapters into RJ-45 office wall outlets, MICROSCANNER can identify office locations at the patch panel.
MICROSCANNER ENGLISH - 17 Office Identifier (MICROSCANNER PRO) The Office Identifier function allows you to find the termination of a twisted pair and/or a coax cable drop from a distribution panel. By inserting the Office Identifier adapters into wall outlets, MICROSCANNER can identify office locations at the distribution panel.
MICROSCANNER ENGLISH - 18 T oner T oner is a cable tracing function that assists in tracking cables hidden in walls, ceilings, floors, or patch panels by generating four distinct multi-tone signals that can be received by a cable tracer .
MICROSCANNER ENGLISH - 19 T echnical Specifications Dimensions: MICROSCANNER : 13.97 cm x 8.25 cm x 2.54 cm (5.5" x 3.25" x 1") Wiremap Adapter: 7.62 cm x 3.18 cm x 2.1 1 cm (3" x 1.25" x .83") Office Identifier: 7.62 cm x 1.
MICROSCANNER ENGLISH - 20 T est Interface: Main: Modular 8 connector for length, 10/100 link identification, wiremap, office identifier/room identifier , trace Loopback: Modular 8 connector for patch .
デバイスMicrotest MICROSCANNERの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Microtest MICROSCANNERをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMicrotest MICROSCANNERの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Microtest MICROSCANNERの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Microtest MICROSCANNERで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Microtest MICROSCANNERを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMicrotest MICROSCANNERの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Microtest MICROSCANNERに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMicrotest MICROSCANNERデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。