MieleメーカーF 1471 VIの使用説明書/サービス説明書
ページ先へ移動 of 84
Operating and Installation instructions Freezer with Ice/Water Dispenser F 1471 Vi To prevent accidents and machine damage read these instructions before installation or use.
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the freezer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Control panel for freezer ........
Water filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Exchanging the water filter ..........................................3 7 Filter Performance Data Sheet . . . . . . . . . . . .
When using the appliance, follow basic safety precautions, including the following: Read all instructions before installation and use to prevent accidents and machine damage. This appliance is intended for residential use only. Use only as described in this Operating manual.
Installation This appliance is top-heavy and must be secured to prevent the possibility of tipping forward. Keep the door closed until the appliance is completely installed and secured per installation instructions. ~ Before installing the appliance, check for externally visible damage.
Use ~ Persons who lack physical, sensory or mental abilities, or experience with the machine should not use it without supervision or instruction by a responsible person. ~ To reduce the risk of injury, do not allow children to play in, on or near the appliance, especially in the door hinge area.
Disposal of your old appliance ~ Before disposing of an old appliance, first make the door latch or lock unusable. ~ Take off the door. ~ Leave the shelves in place so that children may not easily climb inside. ~ Consult with your municipal policy on recycling.
a Interior lighting b Door shelf c Ice cube maker d Ice cube container e Interior shelf f Control panel for the Freezer g Main switch to turn the appliance On/Off h Freezer basket i Water filter j Ice.
Control panel for freezer a Access button " p " activates the control panel b Temperature display X colder; Y warmer Allows you to set the desired temperature in the freezer c On/Off sensor .
Before using for the first time ^ Clean the inside of the appliance and the accessories with a mild solution of warm water and liquid dish soap. Dry with a soft cloth. After installing the appliance, wait at least 30 minutes before switching the appliance on.
Using the settings When a sensor button has been selected with a finger touch, it will appear yellow. A de-selected button will appear white. ^ Touch the access button " p "s oi t turns yellow. On the control panel you will see additional sensor buttons to operate the appliance.
Turning the button sound On/Off If you prefer the buttons to be silent when touched the button sound can be turned off. ^ Touch the access button " p "s oi t turns yellow. ^ Note the position of the X button, but do not touch. ^ Touch the access button " p " again so it turns white.
Turning off for longer periods of time If the appliance is not going to be used for an extended time (for example, during a vacation) some precautions need to be taken: ^ Shut off the water supply lin.
The appliance is equipped with an alarm system, to ensure that the temperature does not rise unnoticed because of energy loss or an open door. The alarm system is always operational, it does not need to be switched on. Temperature alarm If the temperature becomes too warm, an alarm sounds and the "alarm" indicator turns red and flashes.
Setting the temperature ^ Touch the access button " p "s oi t turns yellow. ^ Use the X and Y buttons next to the temperature display to set the temperature warmer or colder. Tap the X and Y sensor buttons to raise/lower the temperature 1°, or hold it down to move through the temperature range more quickly.
Temperature unit (Fahrenheit/Celsius) The temperature can be displayed in degrees Fahrenheit (°F) or Celsius (°C). ^ Touch the access button " p "s oi t turns yellow. ^ Note the position of the button X , but do not touch. ^ Touch the access button " p " again so it turns white.
Freezing food Fresh food should be frozen as quickly as possible. This helps maintain the nutritional value, vitamin content, appearance and taste of the food. Never refreeze partially or fully defrosted food. Consume defrosted food as soon as possible, it will lose its nutritional value and spoil if left for too long.
Defrosting Frozen food can be defrosted in different ways: – in a microwave oven, – at room temperature, – in the refrigerator (the cold given off by the frozen food helps to keep the other food cold), – in a steam oven. Poultry It is especially important to observe proper hygiene when defrosting poultry.
Freezing tips – The following are examples of foods suitable for freezing: Fresh meat, poultry, game, fish, vegetables, herbs, fresh fruit, pastry/dough, leftovers, and a range of pre-cooked meals.
When the SuperCool function is activated, the appliance is cooled as cold as possible (to a factory-preset temperature). SuperCool The SuperCool function is ideal for freezing large quantities of unfrozen food. Ideally the function should be switched o n4-6 hours before the food is placed in the freezer.
For the automatic ice/water dispenser to operate, it must be connected to the household power and water supply. Use sturdy glass when dispensing water or ice - risk of injury from broken glass! Keep fingers clear of the dispenser opening.
^ Turn on the Ice/Water dispenser with a finger touch to the control panel or by passing your hand under the dispenser to activate it via the light sensor. All of the touch controls for the Ice/Water Dispenser should now appear white. If this is not the case, the Safety Lock is activated i.
As soon as the drip tray indicator signals that the drip tray is full, the current operation will automatically stop. Empty out the drip tray using a sponge or dish towel. After the appliance is turned on for the very first time, it can take up to 24 hours for the first ice cubes to drop out of the ice cube maker and collect in the container.
Using the Ice/Water Dispenser for the first time Before using the Ice/Water Dispenser for the first time, you must flush then fill appliance water lines with water. ^ Open the freezer door. ^ Touch the "Access" button so it turns yellow. ^ Touch the "ice" sensor button so it turns yellow.
Safety lock The Ice/Water dispenser can be locked to prevent unwanted use. ^ Touch the "lock" button so it turns yellow. The Ice/Water dispenser buttons are now locked. To unlock the buttons: ^ Touch the "lock" button so it turns white.
Settings The following settings on the Ice/Water dispenser can be adjusted: Entering the settings mode ^ Touch and hold the "lock" button (appears white). ^ At the same time tap the "light" button. ^ Hold the "lock" button for approx.
Anti-clumping The anti-clumping feature ensures that crushed ice or ice cubes do not freeze together. A noise will be heard periodically to indicate that the feature is working. If the sound disturbs you, the feature can be turned off. Note: Disabling the anti-clumping feature can result in the formation of ice clumps in the dispenser.
The freezer defrosts automatically. The moisture generated in the appliance collects in the evaporator. It is automatically defrosted and dissipated by the condenser periodically. This automatic defrosting system enables the freezer to remain permanently ice-free, while ensuring that the food stored in the freezer stays frozen.
Moving the shelves The shelves can be adjusted according to the height of the food. ^ Using both hands, grasp the shelf from underneath and lift slightly so that the rear of the shelf is slightly above the mountings. ^ Pull the shelf forward. ^ Move the shelf to the desired height, then insert the (rear) hooks into place.
Freezer baskets For easier loading, unloading, and cleaning, the freezer baskets can be shifted or completely removed. ^ Pull the basket forward until resistance is felt. On the hinged-side of the door is a safety lock, which must be turned to a horizontal position before the drawer can be removed.
To reduce the risk of electrical shock, disconnect the appliance from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before maintenance. Never use cleaning agents containing abrasive substances such as sand, soda, acids, chlorides or chemical solvents.
Aluminum frames The frames of the door bins and shelves are made of aluminum. ^ Clean with a mild solution of warm water and liquid dish soap. Aluminum is susceptible to scratches and nicks, treat with care. The aluminum frames may become discolored or otherwise altered if soiling is not cleaned away promptly.
Ventilation slits ^ Check the ventilation slits in the base panel regularly. Remove any dirt/dust with a vacuum cleaner or brush. Clean as needed. Door seals Do not use any oils or grease on the door seals. This may cause the seals to deteriorate and become porous over time.
Changing the light bulb The lighting automatically switches off after the door has been open for approx. 10 minutes. This is not a fault. If the light does not come on when the door is opened briefly, the light bulb should be changed. ^ Use the main switch to turn the appliance off.
Side lighting ^ Turn the light cover counterclockwise and pull out. Never touch a halogen bulb with bare fingers. When inserting a glass halogen bulb always hold with a soft cloth. ^ Pull the defective light bulb from the socket. ^ Place the new bulb in the socket.
The water filter improves the taste and smell of ice cubes by removing chlorine and other substances from the incoming tap water. It is important to change the water filter regularly.
Exchanging the water filter ^ Push in and rotate the filter cap on the base panel of your appliance counterclockwise 180°, 1 . ^ Pull the used filter cartridge out of the appliance, 2 . ^ Remove the cap from the used filter, 3 . ^ Take a new filter cartridge out of the packaging and remove the protective cap.
Re-setting the filter indicator The filter indicator still flashes in the display. ^ Touch the access button " p "s oi t turns yellow. ^ Note the position of the button X , but do not touch. ^ Touch the access button " p " again so it turns white.
^ Tap the X button until ^- appears in the display. ^ Touch the access button " p ". ^ Tap the X button until ; appears in the display. ^ Touch the access button " p ". You have left the Custom settings mode. The "filter" indicator is no longer visible on the control panel.
Filter Performance Data Sheet 40 State of California Department of Public Health Water Treatment Device Certificate Number Date Issued: March 10, 2006 T rad e mark /M od e l D e s i g nat i on R e p l.
Filter Performance Data Sheet 41 To a capacity of 739.68 gallons (2800 liters). * Based on the use of Cryptosporium parvum oocysts Performance Data Sheet For Filter Model 07134220 System tested and ce.
With the aid of the following guide minor problems can be corrected without a ser - vice call. Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage and may void the warranty.
General problems Issue Possible fault Solution Water is flowing out of the appliance. Close the shut-off valve immediately. Check whether the water pipe in the appliance is defective. Contact Miele Technical Service. Check whether the water pressure is too low.
Alarm / Indicator warnings Issue Possible fault Solution The alarm is going off. The appliance door(s) have been open for longer than 5 minutes. Close the door. The alarm is ringing and the "alarm" indicator is flashing. The door is not closed.
Problems with the ice/water dispenser Issue Possible fault Solution The ice maker will not switch on. The appliance is not plugged in. Check that the appliance is connected to the power supply.
Problems with the ice/water dispenser Issue Possible fault Solution The ice cubes are small. Other domestic appliances that use water are in operation. Avoid using such items as a dishwasher, washing machine or shower at the same time. Check whether the water filter needs changing.
Problems with the ice/water dispenser Issue Possible fault Solution The ice maker is not producing enough ice or the ice cubes are misshapen. Check the water pressure. The water pressure must be between 25 and 120 psi (1.72-8.25 bar). Contact a plumber.
In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting the Technical Service Department, please quote the model and serial number of your appliance given on the data plate inside the appliance.
Installation instructions To prevent accidents and machine damage read these instructions before installation or use..
Disposal of packing materials The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags, etc.
Have the appliance installed by a qualified technician, according to the enclosed installation instructions. The manufacturer is not liable for damage to property due to an incorrect installation or water connection. WARNING This appliance is top-heavy and must be secured to prevent it from tipping forward.
Base A fully loaded appliance is very heavy. The load-bearing capacity of your floor must meet the following requirements: F 1471 Vi ..........5 0 5l b s (229 kg) To ensure that the appliance is installed securely and functions properly, the base must be flat, level and made of a hard, rigid material.
Custom door panels This appliance is compatible with all styles and designs of kitchen cabinetry. The total weight of the decorative panel(s) must not exceed the following: F 18X1 Vi ...........1 3 4l b s( 6 1k g ) Installation options There are many different installation options.
. . . with partition The minimum thickness of the partition is 5 / 8 " (16 mm). If there is a partition between the adjacent appliances, then each appliance is to be individually installed within its own niche. A heating mat must only be installed if the partition wall is less than 6" (160 mm) wide.
Niche dimensions Niche width (A) F 1471 Vi 18" (457 mm) Dimensions 55.
1. Power supply 2. Water connection A F 1471 Vi 9" (229 mm) Door dimensions (open min. 115°) AB F 1471 Vi 20 11 / 16 " (525 mm) 9 3 / 16 " (234 mm) Dimensions 56.
Dimensions 57.
Before you begin Read these instructions completely and carefully. Have the appliance installed by a qualified technician, according to the enclosed installation instructions. To reduce the risk of injury or damage to the product, two people should be used for installation.
Check the installation niche To ensure a safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation requirements. ^ Check the base (see "Installation"). ^ Check the dimensions of the cavity.
^ Loosen the bracket that holds the appliance to the pallet. , Caution! The appliance is no longer secured and may be unstable. ^ From the rear of the appliance carefully lift it from the pallet. Once the appliance is on the ground it can be wheeled around.
^ Connect the appliance to the power supply and turn it on. After several seconds the indicator light will come on. The indicator light will display different colors one after the other; any control light at the end indicates that the module was correctly installed.
Anti-tip brackets The anti-tip brackets help keep the appliance safely secured to the installation niche to prevent tipping. Two anti-tip brackets are recommended for each appliance or appliance combination (side-by-side). The distance " D " between the anti-tip brackets b is the width of the appliance.
Securing an alternative anti-tip device If the anti-tip brackets cannot be attached securely, an alternative anti-tip device can be used. Ensure that there is no "give" between the appliance and the anti-tip device. If possible, always screw the wooden beam to existing studs.
Sliding the appliance into the installation niche ^ Unscrew the plinth. ^ To protect the corners of the installation space, attach the supplied edge protector a on both sides with adhesive tape. ^ Plug the appliance into the power outlet b . In the case of side-by-side installations, a separate outlet must be used for each appliance.
Aligning the appliance ^ Align the appliance with the custom front. The installation aids e have been designed for the following total thicknesses of custom doors: – 3 / 4 " (19 mm) –1 1 / 2 " (38 mm) Be sure to take into account the possible differing thicknesses of the custom door that is to be fitted subsequently.
Note: – Do not twist or jam the appliance inside the niche. When unscrewing the height-adjustable feet, proceed gradually, alternating between left and right. – The adjustment of the rear feet is aided if the appliance is lifted at the rear (tipped forward slightly).
For a side-by-side combination the filler strips from both appliances are put together to form one long filler strip: ^ Take the peg from the "side-by-side merging kit" and insert it halfway into the filler strip rail on the left-side appliance.
Preparing the custom door ^ Open the appliance door. ^ Unscrew the installation supports n from the appliance door. ^ Loosen the remaining screws from the strips o on each side of the door, then remove. ^ Set aside the screws and side strips o - you will need them again later.
^ Mark the distance X on the back-side of the custom door. ^ Also calculate and mark the center of the custom door Y . ^ Remove the mounting frame from the appliance door and position it according to the markings on the custom door. ^ Pre-drill the holes.
^ Adjust the custom door to adjacent furniture/fixtures. ^ Align the custom door with the double-threaded bolts. ^ Tighten the nuts on the adjusting rail. This will correct the side alignment of the door. ^ Put the side strips (15) back into place and screw them completely down on both sides of the appliance door.
^ Insert the cover strip into the space between the appliance and the side panel. For side-by-side combinations, the cover strips (on both sides of the appliance) are applied to the outermost spaces only. ^ Attach the light switch cover. Attaching the toe-kick panel The maximum height of the toe-kick panel is 4" from the top of the floor.
Mounting the air separator The air separator on the inside of the freezer door keeps the supply and exhaust air separate. This prevents warm exhaust air from flowing into the machine, optimizing the energy performance of the unit. ^ If necessary, shorten the three parts of the air separator.
Aligning the Ice/Water Dispenser If necessary the depth of the Ice/Water dispenser can be aligned from inside the custom door cut-out. This allows the dispenser to be aligned with the custom door to achieve the best possible appearance. ^ Press the dispenser back and pull downwards to remove.
^ Pull the rear cover forward and out. ^ To remove the drip tray, begin by carefully unclipping the water sensors, then bend them gently upward. Once the drip tray has been removed, the four aligners can be accessed to adjust the Ice/Water Dispenser to your liking.
Attaching the frame and the shelf For 3 / 4 " (19 mm) thick custom doors: ^ Slide the cover frame onto the Ice/Water Dispenser and press until it is flush with the door surface (be sure the word "TOP" on the cover frame is upward). For 1 1 / 2 " / (38 mm) thick custom doors: ^ Press the extension frame onto the cover frame.
All plumbing work should be carried out by a suitably qualified and competent person, in accordance with all applicable local and national regulations. The manufacturer is not liable for damage to property due to an incorrect installation or water connection.
Preparing the water connection The connection to the household water supply must be installed before the appliance is installed. ^ Turn off the main water valve to prevent damage caused by leaking water.
Connecting the water supply When connecting the water pipe to the solenoid valve of the appliance, follow the instructions supplied by the manufacturer of the ice cube maker installation kit. When bending the water pipe, be sure not to kink it, otherwise there is a risk of leaks and water damage.
, Avoid the risk of electrical shock - Plug into a grounded 3-prong outlet. - Do not move the ground plug. - Do not use an adapter. - Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Improper connection of the equipment grounding conductor may result in electric shock.
The Miele RemoteVision system is designed to send messages directly to Miele and/or your PC. For information on set-up and installation of the RemoteVision module see the "Installation" section of this manual. Be sure your wireless system meets the following requirements – Windows XP ® or newer operating system, Mac ® OS X 10.
Accessing the RemoteVision control panel ^ Touch the access button " p "s oi t turns yellow. ^ Note the position of the button X , but do not touch. ^ Touch the access button " p " again so it turns white. Only the access button " p " is visible.
MasterCool control panel options for RemoteVision Selectable options Description of function ; - Back ; 2 Reboot the module ; 3 Reset the module to factory settings ; 4 Enter Ad-Hoc Mode Note: If you cannot select any option (other than ; - "back"), the module has not been installed correctly.
83.
Alteration rights reserved / 3408 For the most updated manual see the Miele web site. M.-Nr. 07 155 770 / 00.
デバイスMiele F 1471 VIの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Miele F 1471 VIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiele F 1471 VIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miele F 1471 VIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miele F 1471 VIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miele F 1471 VIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiele F 1471 VIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miele F 1471 VIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiele F 1471 VIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
