MieleメーカーF 9552 iの使用説明書/サービス説明書
ページ先へ移動 of 48
Operating and installation instructions Freezer F 9252 i (-1) F 9552 i (-1) To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time.
Guide to the appliance .............................................4 Caring for the environment ..........................................5 Warning and Safety instructions .....................................6 How to save energy ....................
Defrosting the appliance ...........................................2 4 Cleaning and care ................................................2 6 Cleaning the interior and accessories ..................................2 6 Ventilation gaps ................
a Safety lock indicator light b On/Off button c Temperature display a Freezer drawers with freezer calendar d Temperature selector buttons (+ for warmer; – for colder) e Super freeze button and indi.
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal, and can normally be recycled. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children.
This appliance complies with all relevant legal safety requirements. Improper use can, however, present a risk of both personal injury and material damage. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before installation and before using it for the first time.
Technical safety ~ Before setting up the appliance, check it for any externally visible damage. Do not install and use a damaged appliance. ~ If the connection cable is faulty it must only be replaced by a service technician authorised by the manufacturer to protect the user from danger.
~ The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations.
Correct use ~ Never handle frozen food with wet hands. Your hands may freeze to the frozen food. ~ Do not take ice cubes out with your bare hands and never place ice cubes or ice lollies in your mouth straight from the freezer. The very low temperature of the frozen ice or lollies can cause frost burn to the lips and tongue.
~ Do not block the ventilation gaps in the plinth or the top of the appliance housing unit as this would impair the efficiency of the appliance, increase the electricity consumption and could cause damage to the appliance.
Normal energy consumption Increased energy consumption Installation site In a ventilated room. In an enclosed, unventilated room. Protected from direct sunlight. In direct sunlight. Not situated near to a heat source (radiator, oven). Situated near to a heat source (radiator, oven).
Before using for the first time ^ Clean the inside of the appliance and the accessories with warm water and a little washing-up liquid, and then dry with a soft cloth. Important: To ensure the correct functioning of the appliance, let it stand for between 1½ and 2 hours after transporting it to its final location before connecting it to the mains.
^ Press the On/Off button to come out of setting mode. The electronics will then switch over to normal operation after a couple of minutes. Switching off for longer periods of time If the appliance is not going to be used for a longer period of time, e.
It is very important to set the correct temperature for storing food in the appliance. Micro-organisms will cause food which is not stored at the correct temperature to deteriorate rapidly. Temperature influences the growth rate of these micro-organisms.
If you have adjusted the temperature, wait for approx. 6 hours if the appliance is not very full and for approx. 24 hours if the appliance is full before checking the temperature display as it will take this long for the display to give an accurate reading.
^ Press one of the temperature selector buttons repeatedly until ^ appears in the display. ^ Press the Super freeze button again. ^ lights up in the display. ^ You can now adjust the level of brightness by pressing the temperature selector buttons. You can choose from settings 1 to 5 : 1 : dimmest setting, 5 : brightest setting.
Your appliance has been fitted with a warning system which ensures that the temperature in the freezer cannot rise unnoticed and to avoid energy being wasted if a door is left open. Temperature alarm An alarm will sound and the temperature display will flash if the temperature becomes too warm.
Super freeze Switch the Super freeze function on before putting fresh food into the freezer. This helps food to freeze quickly and retain its nutrients, vitamins, flavours and appearance. Super freeze is not necessary: – when putting in food that is already frozen.
Maximum freezing capacity To ensure that fresh food placed in the freezer freezes through to the core as quickly as possible, the maximum freezing capacity must not be exceeded. The maximum freezing capacity for freezing within a 24-hour period is given on the data plate: "Freezing capacity .
Home freezing Only freeze fresh food which is in a good condition. Hints on home freezing – The following types of food are suitable for freezing: Fresh meat, poultry, game, fish, vegetables, herbs, fresh fruit, dairy products, pastry, leftovers, egg yolks, egg whites and a range of pre-cooked meals.
Before placing food in the freezer ^ When freezing more than 2 kg of fresh food, switch on the Super freeze function for some time before placing the food in the freezer (see "Super freeze"). This also helps to prevent food that is already in the freezer from starting to defrost.
Defrosting Frozen food can be defrosted in different ways: – in a microwave oven, – in an oven using the "Fan" or "Defrost" setting, – at room temperature, – in the refrigerator (the cold given off by the frozen food helps to keep other food cold), – in a steam oven.
Freezer tray The freezer tray is useful for freezing small items such as berries and vegetables. They can be frozen individually and therefore maintain their shape when defrosted. ^ Space the food out loosely on the tray. ^ Hang the tray in one of the upper freezer drawers.
In normal use, ice and frost will form in the freezer. If allowed to accumulate, this will impair the efficiency of the freezer and increase the consumption of electricity. Do not scrape ice and frost off as this can cause damage and render the freezer unusable.
After defrosting ^ Clean the appliance, and then dry it thoroughly. ^ Close the appliance door, insert the plug in the socket and switch the appliance back on. ^ Switch on the Super freeze function so that the appliance can cool down quickly. The indicator light will come on.
Never use cleaning agents containing abrasive substances such as sand, soda, acids, chlorides or chemical solvents. "Non-abrasive" cleaning agents are also unsuitable as they can cause matt areas to appear. Make sure that water cannot get into the temperature selector.
Repairs to electrical appliances should only be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work.
. . . the compressor runs continuously. To save energy, the compressor runs at a lower speed, but for longer, when less cooling is required. . . . food has frozen together. Use a blunt instrument, e.g. a spoon handle or plastic scraper, to prise it apart carefully.
At the end of a power cut, the appliance will start operating again at the last temperature setting selected. . . . the Super freeze indicator light does not light up, even though the appliance is working. The indicator light is defective. Call the Service Department.
Normal noises What causes them Brrrrr... Humming noise made by the motor (compressor). This noise can get louder for brief periods when the motor is switching on. Blubb, blubb.... A gurgling noise can be heard when coolant is circulating through the pipes.
In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee, please contact: – your Miele Dealer or – Miele (see back cover for contact details). When contacting your Dealer or Miele, please quote the model and serial number of your appliance.
Electrical connection U.K. All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations (BS 7671 in the UK). The appliance is supplied with a mains cable and moulded plug ready for connection to an a.
This appliance must be built in, otherwise it could tip up. Location The appliance should be installed in a dry, well-ventilated room. The room temperature should not go above or below the climate range for which the appliance is designed. The higher the ambient temperature of the room, the more energy the appliance requires to operate.
Before installation ^ Before installation remove the cover strip, sealing strip and other accessories from inside the appliance and from the external rear wall of the appliance. ^ On no account should the spacers be removed from the back of the appliance.
Niche height [mm] A F 9252 i (-1) 874 – 890 F 9552 i (-1) 1397 - 1413 Building-in dimensions 35.
The door hinges are set ex-works to enable the door to be opened wide. However, if the opening angle of the door needs to be limited for any reason, the hinge can be adjusted to accommodate this. – For example, if the appliance door hits an adjacent wall when opened, the opening angle can be limited to 90°.
Before building the appliance in, you will need to decide on which side the door is to be hinged. If left hand door hinging is required, follow the instructions below. To change the door hinging you will need the following tools : – a cross-slotted screwdriver, – a screwdriver, – a selection of Torx screwdrivers, – a spanner.
^ Unscrew mounting b and pull soft-close mechanism c downwards to remove it. ^ Undo ball joint d using a spanner and remove it. ^ Stand the appliance door up, and loosen the hinges at the front (the hinges remain open). ^ Remove screws a , and use the stoppers supplied c to plug the empty holes.
^ Push the appliance door onto the pre-fitted screws, and then tighten the screws. ^ Replace covers a , b and c . ^ Replace the locking pins into the top of the hinges to prevent the doors opening too far.
All fitting instructions given are for a right hand hinged appliance. If you have converted the appliance to left hand hinging you will need to adapt these instructions accordingly. To install the appliance you will need the following : – a cross-slotted screwdriver, – a selection of Torx screwdrivers, – a hexagon spanner.
Preparing the appliance ^ Slide cover strip a into the holder in the middle of the appliance as illustrated with the bumps facing downwards. The bumps will fit into the keyhole slots. ^ Position the mains electricity cable so that the appliance can be connected easily once installed.
^ Fit cover g onto fixing bracket h . ^ Secure fixing bracket h to the bottom of the appliance with screws i (M5 x 15). ^ Carefully remove the protective foil from sealing strip j . ^ Apply the sealing strip to the side of the appliance on which the door is opened so that it is flush with the front edge of the appliance.
On furniture with door fittings (e.g. stubs, seals etc) the dimension of these must be taken into account when making sure there is a gap all round of 42 mm . ^ Pull the appliance forwards by the dimension of the door fitting to keep the gap at 42 mm all round.
^ Loosen screws b on the top and bottom fixing brackets c . ^ Press fixing bracket c against the side wall and tighten screws b . ^ Attach fixing bracket c to the housing unit side wall with screws d . Drill holes in the housing unit side walls if necessary.
^ Using a pencil, lightly mark a line down the centre of the inside of the furniture door. ^ Hang fixing bracket d with the fitting aids onto the inside of the furniture door. Align the fixing bracket centrally. ^ Attach the fixing bracket securely using at least 6 short chipboard screws e (4 x 14 mm).
Securing the appliance door to the furniture door: ^ Screw fixing bracket a into the pre-drilled holes in the appliance door using hexagonal screw b . Make sure the two metal edges c are aligned (Symbol II ). ^ Drill fixing holes d in the furniture door, and screw i n4x1 4m m screws e .
^ Replace all the covers. To make sure the appliance is correctly fitted: – The door must close properly. – The door must not touch the furniture carcase. – The seal at the top edge of the handle side must fit properly. To double check place a torch in the appliance and close the doors.
M.-Nr. 07 465 401 / 03 Alteration rights reserved / 4209 F 9252 i (-1), F 9552 i (-1).
デバイスMiele F 9552 iの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Miele F 9552 iをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiele F 9552 iの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miele F 9552 iの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miele F 9552 iで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miele F 9552 iを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiele F 9552 iの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miele F 9552 iに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiele F 9552 iデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
