MieleメーカーG 2670 SCの使用説明書/サービス説明書
ページ先へ移動 of 76
Operating Instructions Excella Ser ies G 2670 SC T o prevent accidents and machine damage read these instructions before installation or use. UV M.-Nr .
IMPORT ANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Control panel . . . . . . . . . . . . .
Additional functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Delay Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Settings J .
W ARNING – When using your dishwasher , f ollow basic precautions, including the follo wing: Read all instructions before installation or use of the dishwasher to prevent injury and machine damage. The manufacturer cannot be held responsible for damage or injury caused by improper use of this appliance.
Installation The dishwasher must be installed and connected in compliance with the installation instructions. Installation and repair work should be perfor med by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty .
Use T o reduce the risk of injury , do not allow children to play in, on or near the dishwasher . Only use the dishwasher if all panels are pr operly in place. Do not tamper with the controls. Do not damage, sit or stand on the door or baskets of the dishwasher .
a Upper spray arm (not visible) b Cutlery tray (depending on model) c Upper basket d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm g Filter combination h Data plate i .
Control panel a Selection buttons T o select a menu point from this display , to change the displayed value (+/-) or to browse between menus. b Display See the following pages for more information. c + C (Clear) button T o switch back to the previous menu level or to discard a selected setting.
Display function The following can be selected in the display – the wash program – the options – the start time – the settings J menu During a running program the display shows – the program.
Energy sa ving washing This dishwasher is exceptionally economical in the use of water and electricity . For best results follow these tips: ^ For lowest energy consumption and the gentlest washing of china and crystal, connect the dishwasher to a cold water source.
T o open the door ^ Pull the handle to open the door . If the door is opened during operation, the dishwasher will stop running. Once the door is closed the program will continue. T o close the door ^ Push the baskets in. ^ Lift the door and push until it clicks into position.
W elcome screen ^ T ur n the dishwasher on g . A Welcome scr een shows when the washer is tur ned on for the first time. Language setting The display changes automatically to the language setting. The selected language is marked with a L check. } deutsch B Sprache F e } english (GB) OK } ^ Select the desired language and confirm with OK .
W ater softener Every dishwasher is tested before leaving the factory . Any water remaining in the machine is fr om the final factory test and does not indicate that the machine has been used. T o achieve good cleaning results the dishwasher needs soft water .
Filling the salt container , Inadvertently filling the salt container with dishwashing detergent will damage the water softener . , Only use water softener salt specially formulated for dishwashers. Other salts may contain insoluble additives which can impair the water softener .
Salt refill message ^ When the display shows k Refill salt , refill the salt container after the program has finished. ^ Confirm with OK. The message will clear from the display . After the container has been filled, the water softener is automatically reactivated the next time the dishwasher is started.
Rinse aid Rinse aid helps to prevent spotting on dishes and glassware. The rinse aid is filled in the reservoir and the set amount will be automatically dispensed. , Filling the rinse aid reservoir with detergent will damage the reservoir . Only pour rinse aid formulated for residential dishwashers into the reservoir .
^ Pour liquid rinse aid into the reservoir until it its visible on the surface of the screen. The rinse aid reservoir holds appr ox. 3.7 oz (110 ml) of liquid. ^ Press on the flap until you hear it click shut. Failure to close it all the way allows water to enter the reservoir during the wash pr ogram.
, Do not wash items soiled with ash, sand, wax, grease or paint in the dishwasher . Ash and sand do not dissolve and will be distributed throughout the inside of the dishwasher . W ax, grease and paint will cause permanent discoloration and damage to the dishwasher .
Items not recommended for dishwashing – Cutlery with wooden handles – Wooden cutting boar ds – Glued items such as old knives with handles glued together around the shank of the blade – Handma.
Split cutlery tray ^ Arrange the cutlery as shown in the cutlery tray . For easier unloading cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. Place knives with the cutting edge and forks with the prongs between the holders.
Upper basket , For safety reasons only use the dishwasher with the upper and lower basket inserted. Exception: The programs "Large items normal" and "Large items soiled" are designed for use without the upper basket.
Adjustable cup rac ks ^ Raise the rack to make room for tall glasses. Lower it to double stack smaller pieces. The height of the cup rack can be adjusted in two levels. ^ Pull the cup rack upwards and let it engage at the desired height. Coffee bar (depending on model) Glasses can be leaned against the coffee bar for a secur e stand.
Glassware rail (depending on model) The glassware rail is designed for a secure stand of tall glasses and stemmed glassware. ^ Flip the bar down to lean tall glasses on it. If necessary take out a par t of the cutlery tray to make room for tall glasses.
Adjusting the upper basket The upper basket can be raised or lowered to accommodate tall items. The basket can also be angled to fit tall items in both, the upper and lower baskets. The angles should not be set to opposite extremes. This will block the middle spray arm.
Lower basket ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Loading the dishwasher 25.
Comfort inserts The comfort inser ts are designed for cups, glasses, plates, bowls, pots, etc. ^ T o insert tall items, raise the cup rest. ^ Lean or hang stemmed glassware such as wine or champagne glasses in the cut outs of the cup rest. PlateGuard Plus with StemGuar d Removing an insert a : ^ T o remove an insert, gently pull up on the handle.
Remov able spike inser t with StemGuard Removing: ^ Push the insert down, a and at the same time push the latch towards the basket, b . V ase/Bottle holder The vase/bottle holder , e.g. for vases and baby bottles, can be inserted into the lower basket as shown in the illustration.
Additional inserts for the upper and lower baskets may be purchased from your Miele dealer or Miele. Depending on model some accessories come standard with the machine.
Detergent , Dishwasher detergents contain irritant and corrosive ingr edients. Avoid inhaling or swallowing dishwasher detergent. Keep children away fr om detergent. Fill the detergent dispenser only when you are r eady to star t the dishwasher . , Only use detergents formulated for domestic dishwashers.
Adding deter gent ^ T o open, press the latch on the detergent dispenser . The flap will spring open. The flap is always open at the end of a program. ^ Add detergent to compartment II and close the flap. ^ If a Pre-rinse is desir ed, and available for your chosen program, add 1 teaspoon (5 ml) of detergent to compartment I.
T urning on ^ Open the water supply , if it is closed. ^ Open the door . ^ Make sure the spray arms can rotate fr eely . ^ T ur n the dishwasher on g . The main menu shows in the display . If the memory function is selected, the last selected program is displayed.
Program When to use Program sequence Pre- rinse 12 Main wash Interim rinse 12 Final rinse Drying Normal For normally soiled dishware with dried on food Run-time 131 min XX X X X X Pots + Pans For norm.
Program When to use Program sequence Pre- rinse Main wash Interim rinse 12 Final rinse Drying Starch For dishware with dried on starc hy f ood ; 120% detergent recommended Run-time 148 min XX X X X Cheese For dishware with dried on cheese ; 120% detergent recommended Run-time 150 min XX X X X Sani W ash T o sanitize dishware , e.
Selecting Options Options can be added to the selected program. ^ Select Options . The display shows the available options for the selected program. Available options: Pre-rinse: – For easily removable soiling Soak: – T o soak stubborn soiling. When using powder detergent, fill approx.
Y ou can now select the detergent used. Available selections ar e: Powder , Gel, "2 in 1" and "3 in 1". See "Settings J - Detergent". Starting a program ^ Select Start . The display shows Close the door . T o select another program or to add options, select Back and cancel the program with Cancellation .
At the end of a program At the end of a program the optical control light flashes slowly with the door closed. The optical function light goes out one hour after the end of a program. At the end of a program the display shows Program finished . Dishes tends to chip if removed still hot from the dishwasher .
Changing a program If the detergent flap is already open, do not change the program. If a program has alr eady star ted and you wish to change it: ^ Open the door . Sensor Wash 1:32 h 12:00 Main wash Cancellation } ^ Select Cancellation and confirm with OK .
Delay Start The starting time of a program can be delayed. The start time can be delayed between 15 minutes and 24 hours. The start can be delayed in 15-minute-increments. When using the "Delay Start" function, make sure that the detergent compartment is dr y before adding detergent.
^ Confirm with OK . The display changes to the program menu. ^ Select Start . ^ Close the door . The program starts automatically at the selected time. The indicator d goes out. Starting a program before the dela y star t has elapsed: A program can be started before the delay start time has elapsed.
The "Settings J " menu allo ws y ou to adjust standar d settings Opening the Settings J menu ^ T ur n the dishwasher on by pressing the g button. The main menu shows in the display . If the memory function is selected, the last selected program is displayed.
Language J The display contents can be shown in differ ent languages. The displayed language can be changed by the submenu "Language J ". ^ Select the desired language and confirm with OK . The flag behind the word "Language J " serves as a guide when an unfamiliar language is selected.
Detergent T o achieve the best results the used detergent can be set on your dishwasher . The selection allows "Powder", "Gel", "2 in 1" and "3 in 1" tabs. The program cycle sequence will be adjusted for the selected detergent.
W ater hardness The dishwasher is equipped with a sensor softener , which automatically detects the hardness of your tap water . After plumbing the dishwasher and finishing a program, e.g. "Rinse & Hold", the water hardness is displayed in the menu "W ater hardness".
Reorganize pr ogram list The order of the pr ograms in the program list can be reorganized. The two most fr equently used programs can be saved to the first two positions. } Sensor Wash B e } Cancel Select program for position 1 Continue } ^ Select with e the program which you would like to save to the first position of the main menu.
Save options Additional options can be selected for some programs, e.g. extended drying. See "Use - Selecting options". Save options allows to save the selected options for future use of the program. This function is turned off by default. ^ Select the desired setting and confirm with OK .
Buzzer When the buzzer is activated, a tone sounds at the end of a program and if a fault occurs. The buzzer is turned on by default. Buzzer at the end of a program The buzzer at the end of a program sounds five times in intervals with a brief break in between.
Ke ypad tone A tone will sound when a button is pressed. The button tone is turned on by default. ^ Select the desired option and confirm with OK . Brightness The display brightness can be adjusted in 17 levels. The contrast is set to level 8 by default.
Dealer Demo modes are only for showrooms. The dishwasher has three demo programs for showr ooms. The programs "Demo mode" and "Endless demo mode" show the use and the function range of the dishwasher . – Demo mode : The program is started by pressing any button.
With the aid of the following guide, minor problems can be fixed without a service call. , Repairs should only be carried out by a qualified and trained person in accordance with local and national safety r egulations. Unauthorized repairs could cause personal injury or machine damage.
Issue P ossible fault Solution The optical interface flashes fast, the buzzer sounds or the display shows the fault: Technical fault Call Technical Service Ther e may be a technical fault. – T ur n the dishwasher off o . After a few seconds: – T ur n the dishwasher on.
Prob lems water intake/drain Issue P ossible fault Solution The optical interface flashes fast, the buzzer sounds and the display shows the fault: Close the door and open the water supply. The water supply is closed. Open the water supply all the way .
Issue P ossible fault Solution The optical interface flashes fast. The program "Ener gy Saver" displa ys the fault: Water intake temp. too low The intake water does not have a minimum temperature of 115°F (45°C). See "Plumbing - Connection to the water supply".
General prob lems with the dishwasher Issue P ossible fault Solution The display remains off. The display has gone into "Standby" mode to save energy . Press a button. The display turns on again. The buzzer sounds during the program and the display shows: Close the salt container lid The salt container lid was not screwed on properly .
Issue P ossible fault Solution Detergent is left in the dispenser at the end of a program. The dispenser was damp when detergent was added. Dry the dispenser before adding detergent. The detergent lid cannot be closed properl y . Detergent residue is blocking the catch.
Sounds Issue P ossible fault Solution There is a knocking noise in the wash cabinet. The spray arm is hitting an item in the basket. Interrupt the program, rearrange items blocking the spray arms. There is a rattling noise in the wash cabinet. Items are not secur e in the wash cabinet.
P oor cleaning results Issue P ossible fault Solution The dishes are not clean. The dishes were not loaded correctly . See "Loading the dishwasher". The program was not powerful enough. Select a more intensive program, see "Pr ogram Guide".
Issue P ossible fault Solution Dishes are not dry , glasses and cutlery are spotted? The rinse aid setting may be too low or the rinse aid reservoir is empty . Increase the dosage, r efill the reservoir or switch the rinse aid product when refilling, see "Befor e using for the first time".
Issue P ossible fault Solution Glasses are discolored and the film cannot be wiped off. Detergent ingredients have been deposited on the glasses. Use a differ ent detergent. Glasses are dull and discolored and have a film which cannot be wiped off. Glasses are not dishwasher safe.
Repairs In the event of a fault which you cannot correct yourself please contact the Miele Service Department at the phone number on the back of this booklet. ^ Please quote the model type and number of your appliance. These can be found on the data plate along the right edge of the door .
T o transport the dishwasher , e.g. when moving to a new home, note the following: – Empty the dishwasher . – Secure any loose parts, e.g. hoses, cables, cutlery baskets. – T ranspor t the dishwasher in the upright position. If unavoidable it may be transported on its back.
User Maintenance Instr uctions T o prevent accidents and machine damage, read these instructions before installation or use..
Check and clean your dishwasher regularly (appr ox. ever y 4-6 months). This will help avoid faults and problems. , Abrasive cleaning agents, glass cleaning agents, all-purpose cleaners, thinner or ammonium cleaners should not be used on the dishwasher .
T riple filter system The triple filter system in the base of the wash cabinet prevents food fr om being redeposited on dishes. It also pr otects the circulation pump fr om damage caused by foreign objects (e.
T o clean the underside of the filter , the flap must be opened. ^ Push the clips together a and open the flap b . ^ Rinse under running water . ^ Close the flap so that the clip engages. ^ Return the filter so it lies flat in the base of the wash cabinet.
Cleaning the spray arms Sometimes particles of food get stuck in the spray arm jets. The spray ar ms should be inspected and cleaned every 4 - 6 months. ^ T ur n off the dishwasher before cleaning. Removing the spra y arms ^ Remove the cutlery tray (if present).
Cleaning the water inlet filter A filter is incorporated into the intake hose attached to the dishwasher’ s shut off valve. If your water is har d or the pipes contain sediment, this filter may clog and prevent enough water fr om entering the wash cabinet.
Cleaning the drain pump and non-return valve If the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ T ur n off the dishwasher and pull the plug. ^ Remove the triple filter (see "T riple filter system").
68.
Installation Instr uctions For installation of the dishwasher please refer to the Installation Sheet supplied with these instructions..
Disposal of the packing material The cardboar d box and packaging protect the appliance during shipping. These materials are biodegradable and recyclable. Please r ecycle. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of childr en.
, Installation, repairs and other work by unqualified persons could be dangerous. The manufactur er cannot be held responsible for unauthorized work. Check that the voltage, frequency and fuse rating shown on the data plate match the household mains supply .
Connection to the water supply , Do not drink water from the dishwasher! – The dishwasher can heat its own water to the temperature r equired by the wash program. This allows for connection of the machine to either a hot or cold water source. For lowest energy consumption connect the dishwasher to a cold water source.
Drainage – The machine comes equipped with a built-in non-return valve on the discharge side to prevent waste water from flowing back into the dishwasher . – The dishwasher is equipped with a 5 ft (1.5 m) flexible drain hose with an internal diameter of 7/8" (22 mm).
74.
75.
Alterations reserved/4906 G 2670 Vi / M.-Nr . 06 696 120 / 02 e n-U S.
デバイスMiele G 2670 SCの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Miele G 2670 SCをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiele G 2670 SCの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miele G 2670 SCの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miele G 2670 SCで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miele G 2670 SCを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiele G 2670 SCの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miele G 2670 SCに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiele G 2670 SCデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
