MieleメーカーG 856 SC ELITEの使用説明書/サービス説明書
ページ先へ移動 of 52
Operating instructions No v otronic G 856 SC Elite T o prevent accidents UV and machine damage, read these instructions before installation or use. M.-Nr .
2.
IMPOR T ANT SAFETY INSTR UCTIONS MESURES DE SÉCURITÉ IMPOR T ANTES Caring for the en vir onment Energy saving washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Guide to the dishwasher W ash cabinet .
Operation Adding detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Running the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Program sequence indicator (14) .
W ARNING – When using your dishwasher , follo w basic precautions, including the f ol - lowing: Read all instructions before installa - tion or use of the dishwasher to pre - vent injury and machine damage. The manufacturer cannot be held r e - sponsible for damage or injury caused by improper use of this ap- pliance.
Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children. Danger of suf focation! This dishwasher should only be in - stalled under a continuous countertop secured to adjacent cabinetry .
A VERTISSEMENT – A u moment d’utiliser votre lave-v aisselle, veuillez observer toutes les mesures de sécurité de base. Cet appareil électroména ger est con- forme à tous les règlements et codes sur la sécurité.
Au moment de remplir le lave-vais - selle : – Mettre les articles pointus de manière à ce qu’ils n’endommagent pas le seau étanche de la porte.
Energy sa ving washing This dishwasher is exceptionally eco - nomical in the use of water and electric - ity . For best results follow these tips: ^ For lowest energy consumption and the gentlest washing of china and crystal, connect the dishwasher to a cold water source.
W ash cabinet 1 Upper spray arm (not visible) 2 Cutlery tray 3 Upper basket 4 W ater feed for middle spray arm 5 Middle spray arm 6 Lower spray arm 7 Four height adjustable feet 8 T riple Filter Syste.
Control panel 13 "On/Off" button 14 Program sequence display 15 "T op Solo" button 16 Delay Start display 17 Program selector 18 "Delay Start" button 19 "Start" button 20 Check/Refill indicators 21 Child Safety Lock 22 Door release 23 Drying vent Every dishwasher is tested before leaving the factory .
T o open the door ^ Press the r elease catch inside the door grip. If the door is opened during operation, the dishwasher will stop running. Once the door is closed the program will r e- start. T o close the door ^ Push the baskets in. ^ Lift the door and push until it clicks into position.
W ater softener T o achieve good cleaning results, the dishwasher needs soft water . Hard water results in calcium deposits on dishware and in the dishwasher . If your tap water hardness is above 8 gr/gal (values are in US gallons) (140 ppm), the water should be soft - ened.
Programming the water softener Y our water hardness level must be pro - grammed into the dishwasher using the program selector and buttons on the control panel. ^ Make sure the dishwasher is turned off. ^ T ur n the program selector to "Stop".
^ Press the "T op Solo" button. The "T op Solo" indicator will light. ^ T ur n the program selector to "Stop". ^ T ur n off the dishwasher . The programmed water har dness is stored. Checking the pr ogrammed water hardness ^ Make sure the dishwasher is turned off.
Filling the salt reservoir If your water hardness level is gr eater than 8 gr/gal, the salt reservoir should be filled before the first use and when the "Salt" indicator lights. Only use water softener salt specially formulated for dishwashers.
Salt indicator When the salt reservoir is empty , the "Salt-PC" indicator will light, indicating that it should be refilled with r eactiva - tion salt. After the reservoir has been filled, the water softener is automatically reacti- vated the next time the dishwasher is started.
Rinse aid Rinse aid is recommended to pr event spotting on dishes and glassware. , Filling the rinse aid reservoir with detergent will damage the reservoir . Only pour rinse aid formulated for residential dishwashers into the reservoir . Adding rinse aid ^ Add rinse aid before the first use and whenever the "Rise aid" indicator lights.
Adjusting the dosage The dosage selector is preset to 3. This dispenses approximately 3 ml of rinse aid per program. It can be adjusted from 1 to 6. ^ Use a higher setting if spots appear on dry glassware. ^ Use a lower setting if streaking ap- pears on dishes or glasses.
, Do not wash items soiled with ash, sand, wax, grease or paint in the dishwasher . Ash and sand do not dissolve and will be distributed through out the in - side of the dishwasher . W ax, grease and paint will cause permanent discoloration or damage to the dishwasher .
Items not recommended for dishwashing – Cutlery with wooden handles. – Wooden cutting boar ds. – Glued items such as old knives with handles glued together around the shank of the blade. – Hand made craft items, antique, metal trimmed or decorative glass - ware.
Cutlery tray (SC units) The removable cutlery tray makes un- loading flatware easy . Simply carry the cutlery tray to where the flatware is stored and put the entir e basket away in one trip. For easier unloading cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc.
Upper basket Adjusting the upper basket On select models, the upper basket can be raised or lowered to accommo - date tall items. ^ Slide out the upper basket. ^ Pull up the levers at the sides of the upper basket and adjust the basket height. ^ Release the levers and the basket will lock in place.
Adjustable cup rac ks Raise the rack to make room for tall glasses. Lower it to double stack smaller pieces. Coffee bar T o allow water to run off the bottom of coffee mugs, place slanted on top of the coffee bar . The bar can also be used to separate two rows of glasses.
Lower basket For larger and heavier items such as plates, serving platters, sauce pans, bowls. Dishwasher with cutlery tray Height limit The guide at the front of the upper bas- ket determines the maximum height for items placed in the lower basket so that the middle spray arm is not blocked.
V arious removable inserts are available for the lower basket to accomodate spe - cial items to be washed. Removing an insert ^ T o remove an insert, gently pull up on the handle. Inserting an inser t ^ Slid the hitches of the inset under the vertical struts of the lower basket.
Foldable spike insert A highly flexible design holds tableware securely . It can be folded out of the way for pots, pans and other large items. This insert secures plates and platters. Foldable spikes T wo rows of spikes can be folded down, to create mor e room for larger dishware e.
PlateGuard Plus insert A unique design cradles plates at 3 points and can be used for washing cups, glasses, plates, bowls and pots. ^ Hook the PlateGuard Plus insert into the left half of the lower basket, the area marked in white. Bottle holder The bottle holder e.
Additional inserts for the upper and lower baskets may be purchased from your Miele dealer or the Miele T echnical Service Department. Bottle holder part # 03 857 850 to wash milk or baby bottles Glas.
Adding deter gent , Dishwasher detergents contain irritant and corrosive ingr edients. Keep children away fr om detergent. Do not fill the detergent dispenser until you are r eady to start the dish - washer . Only use powder detergents or tab - lets formulated for residential dish - washers.
Running the dishwasher ^ Make sure the spray arms are not blocked. ^ Close the door . ^ T ur n on the dishwasher . The "Start" indicator (19) will flash. ^ Select a wash program by turning the program selector (17) to the left or right. Refer to the "Program guide" for details.
At the end of a program The "End" indicator will light when the program has finished. ^ T ur n the program selector (17) to "Stop". The "End" (14) indicator will go out and the "Start" (19) indicator will flash.
Program guide Program When to use Program cycle Pre- wash 12 Main wash Interim rinse 12 Final rinse Dry- ing Pots & Pans for heavil y soiled pots and pans with dried on food Main wash temperature .
Additional features "T op Solo" (15) Using "T op Solo" will save water and energy . This program is r ecommended when there is only a small load to clean. "T op Solo" can be selected with all pro- grams. With this feature, water is dir ected only to the top and middle spray arms in the dishwasher .
Delay Start (18) The start time of a program can be de- layed from 1 to 9 hours. The delay start is set in one hour steps. , When using delay start, make sure the detergent compartment is dry before adding detergent. Wipe dry if necessar y . ^ T ur n on the dishwasher with the "On/Off" (13) button.
T o start a program before the dela y start period has elapsed: ^ T ur n the program selector (17) to "Stop" for at least one second. The delay start display (16) will go out. ^ T ur n the program selector (17) to the desired pr ogram. ^ Select "T op Solo" again, if needed.
Extended drying If desired drying results ar e not consis - tently achieved, the turbothermic cool - ing fan can be programmed to run an extra 14 minutes at the end of each program. The "Extended drying" feature can also be activated to prevent condensation from collecting on the steam deflector .
With the aid of the following guide, minor problems can be fixed without a service call. , Repairs should only be carried out by a qualified and trained person in ac - cordance with local and national safety r egulations. Unauthorized repairs could cause personal injury or machine damage.
What if … P ossible fault Fix the "Intake/Drain" indi - cator is lit or flashing and the dishwasher may have stopped? The water valve is closed. Open the water valve. The filter in the water inlet is blocked. See maintenance instruc - tions.
What if … P ossible fault Fix the "End", "Star t" and "T op Solo" indicators flash at the same time at the end of a program? There may be a technical fault. – T ur n the program selec - tor to "Stop". – T ur n off the dishwasher .
What if … P ossible fault Fix dishes are not clean? The dishes were not loaded correctly . See, "Loading the dish - washer". The program was not powerful enough. Select a more intensive program see, "Pr ogram guide". Not enough detergent was dispensed.
What if … P ossible fault Fix plastic items are discol - ored? Natural dyes e. g. from vegetables may be the cause. Not enough deter - gent was used to break down natural dyes. Use more detergent, see "Adding detergent". Discoloration is perma - nent.
In the event of a fault which you cannot correct yourself please contact: – Y our Miele Dealer or – The Miele T echnical Service Depart - ment. USA 1-800-999-1360 techserv@mieleusa.com CDN 1-800-565-6435 service@miele.ca When contacting the Miele T echnical Service Department, please quote the model and serial number of your appli- ance.
T o transport the dishwasher , e. g. when moving to a new home, note the follow - ing: – Empty the dishwasher . – Secure any loose parts, e. g. hoses, cables, cutlery baskets. – T ranspor t the dishwasher in the up - right position. If unavoidable it may be transported on its back.
User Maintenance Instr uctions T o prevent accidents and machine damage, read these instructions before installation or use..
T riple filter system The triple filter system in the base of the wash cabinet prevents food fr om being redeposited on dishes. It also pr otects the circulation pump fr om damage caused by foreign objects (e.g. br oken glass, bones). The filter system should be cleaned ev - ery 4 - 6 months or whenever a foreign object is trapped.
T o clean the underside of the filter , the flap must be opened: ^ Pull back the yellow clip. ^ Rinse all parts under running water . Scrub with a nylon brush if neces- sary . ^ Close the flap so that the clip en- gages. ^ Return the filter so it lies flat in the base of the wash cabinet.
Cleaning the spray arms Sometimes particles of food get stuck in the spray arm jets. The spray ar ms should be inspected and cleaned every 4 - 6 months. ^ T ur n off the dishwasher befor e clean - ing. Remove the spray arms as follows: ^ Remove the cutlery tray (if present).
Cleaning the wash cabinet Generally , the wash cabinet is self cleaning if the correct amount of dish - washer detergent is used. The wash cabinet can be cleaned with a dishwasher cleaner such as Dis Cleaner available from your Miele dealer or the Miele T echnical Service Department.
Cleaning the water inlet filter A filter is incorporated in the intake hose attached to the dishwasher’ s shut off valve. If your water is har d, or the pipes contain sediment, this filter may clog and prevent enough water fr om entering the wash cabinet.
Cleaning the drain pump and non-return valve If the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ T ur n off the dishwasher . ^ Remove the triple filter (see "Cleaning the filter in the wash cabinet").
Alterations rights reserved (G 856 / G 857 Plus) / 000 2501 This bio-friendly paper was bleached without the use of chlorine..
デバイスMiele G 856 SC ELITEの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Miele G 856 SC ELITEをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiele G 856 SC ELITEの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miele G 856 SC ELITEの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miele G 856 SC ELITEで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miele G 856 SC ELITEを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiele G 856 SC ELITEの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miele G 856 SC ELITEに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiele G 856 SC ELITEデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
