Mieleメーカーkm 6316の使用説明書/サービス説明書
ページ先へ移動 of 76
Operating and installation instructions Ceramic hobs with induction KM 6316 KM 6319 KM 6321 To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. M.-Nr.
Guide to the appliance .............................................4 KM 6316 .......................................................4 KM 6319 / KM 6321 ..............................................5 Control panel ....................................
Safety features ...................................................3 9 Safety lock / System lock ...........................................3 9 Stop and Go ......................................................4 1 Safety switch-off ...................
KM 6316 a Cooking zone with WaterBoost bc Cooking zones with Booster d Control panel Guide to the appliance 4 a b c d.
KM 6319 / KM 6321 a Cooking zone with WaterBoost bcd Cooking zones with Booster e Control panel Guide to the appliance 5 e a b c d.
Control panel (Example) Sensor controls a For switching the hob on and off b Numerical keypad - For setting the power level - For setting the time c Safety lock d Booster / WaterBoost e For selecting .
Indicator lights i Safety lock j Booster Cooking zone displays k 0 = Cooking zone ready for use ^ = Keeping warm function 1 to 9 = Power levels f = WaterBoost level 1 h = Booster/WaterBoost level 2 ß.
Cooking zones KM 6316 Cooking zone Minimum to maximum C in cm 1) Rating in watts for 230 V 2) f 14 - 28 Normal WaterBoost level 1 WaterBoost level 2 2300 3) 3200 3) 5000 3) x 14 - 20 Normal Booster 18.
This appliance complies with all relevant safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before installation and before using it for the first time.
Correct application ~ This hob is not designed for commercial use. It is intended for use in domestic households and similar working and residential environments. ~ The appliance is not intended for outdoor use. ~ It is intended for domestic use only to cook food and keep it warm.
Safety with children ~ Children under 8 years of age must be kept away from the appliance unless they are constantly supervised. ~ Children 8 years and older may only use the appliance unsupervised if they have been shown how to use it in a safe way and understand the hazards involved.
Technical safety ~ Installation, maintenance and repairs may only be carried out by a Miele authorised service technician. Installation, maintenance and repairs by unqualified persons could be dangerous. ~ A damaged appliance can be dangerous. Check the appliance for visible signs of damage.
~ While the appliance is under guarantee, repairs should only be undertaken by a service technician authorised by Miele. Otherwise the guarantee is invalidated. ~ The manufacturer can only guarantee the safety of the appliance when original Miele replacement parts are used.
Correct use ~ Oil and fat can overheat and catch fire. Do not leave the appliance unattended when cooking with oil or fat. If oil or fat does catch fire, do not attempt to put out the flames with water. Disconnect the appliance from the mains and use a suitable fire blanket, saucepan lid, damp towel or similar to smother the flames.
~ If the appliance is installed behind a kitchen furniture door, it may only be used with the furniture door open. Do not close the door whilst the hob in use or whilst there is any residual heat present. ~ The appliance gets hot when in use and remains hot for a while after being switched off.
~ Do not use pots or pans on the hob with bases with pronounced edges or ridges. These could scratch or scour the ceramic glass surface permanently. Only use pots and pans with smooth bases. ~ Grains of salt, sugar and sand (e.g. from cleaning vegetables) can cause scratches if they get under pan bases.
~ Metal utensils stored in a drawer under the hob can become hot if the appliance is used intensively for a long time. Do not store any metal items or utensils in a drawer under the hob ~ This hob is fitted with a cooling fan.
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled. Recycling the packaging reduces the use of raw materials in the manufacturing process and also reduces the amount of waste in landfill sites.
Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the "After sales service, data plate" section of this booklet. Cleaning for the first time ^ Remove any protective wrapping and adhesive labels.
The induction principle An induction coil is located under each cooking zone. When a cooking zone is switched on, this coil creates a magnetic field which impacts directly on the base of the pan and heats it up. The cooking zone itself is heated up indirectly by the heat given off by the pan.
Noises When using an induction cooking zone, the following noises can occur in the pan, depending on what it is made of and how it has been constructed. – On the higher power settings, it might buzz. This will decrease or cease altogether when the power setting is reduced.
Pans Suitable pans include: – stainless steel pans with a magnetic base – enamelled steel pans – cast iron pans Unsuitable pans: – stainless steel pans without a magnetic base – aluminium an.
How the hob is operated The hob is equipped with electronic sensor controls which react to finger contact. To operate the hob, touch the relevant sensor. Each time you touch a sensor, an audible tone sounds. In order to set or alter a power level or the time, the cooking zones and the timer must be "active".
Switching on The hob must be switched on before any of the zones can be used. Do not leave the appliance unattended whilst it is being used. To switch the hob on ^ Touch the s sensor. 0 will appear in each of the cooking zone displays. If no further entry is made, the hob will switch itself off after a few seconds for safety reasons.
Power level range The appliance is delivered with 9 power levels programmed as standard. If you wish to fine-tune a setting, you can extend the power level range (see "Programming"). The intermediate setting will be represented by an illuminated dot next to the number.
Auto heat-up When Auto heat-up has been activated, the cooking zone switches on automatically at the highest power setting and then switches to the continued cooking setting selected. The heat-up time depends on which continued cooking setting has been chosen (see chart).
Continued cooking setting* Heat-up time in minutes and seconds (approx.) 1 0:1 5 1 . 0:1 5 2 0:1 5 2 . 0:1 5 3 0:2 5 3 . 0:2 5 4 0:5 0 4 . 0:5 0 5 2:0 0 5 .
Booster function The cooking zones are equipped with a Booster or WaterBoost (see "Guide to the appliance"). When activated, the power is boosted for 15 minutes so that large quantities can be heated quickly, e.g. when boiling water for cooking pasta.
To switch on the Booster ^ Touch the sensor for selecting the cooking zone you want. ^ Select a power level if you wish. ^ Touch the B I/II sensor. The indicator lamp for the booster lights up, and h starts to flash in the display. After a few seconds, h will light up constantly and the indicator lamp will go out.
Keeping warm function Each cooking zone has a keeping warm function ("h"). The "h" function is in between the "0" setting and the "1" setting. If the keeping warm function has been activated, the cooking zone will switch off automatically after a maximum of 2 hours.
Switching off and residual heat indicators Switching off a cooking zone ^ Touch the sensor for selecting the cooking zone you want twice. A 0 will flash in the cooking zone display for a few seconds. If the cooking zone is still hot, the residual heat indicator will then appear in the display.
– Use a pan lid whenever possible to minimise heat loss. uncovered covered – Select a smaller pan when cooking small quantities. A smaller pan uses less energy than a larger pan with very little in it.
The hob must be switched on to use the timer. The timer can be used for two different functions: – to set the minute minder – to set a cooking zone to switch off automatically. You can select a time from 1 minute ( 01 ) to 9 hours ( 9^ ). A time of up to 99 minutes is set and displayed in minutes.
Minute minder To set the minute minder time Minutes Example: You want to set 15 minutes. ^ Switch the hob on. ^ Touch the m sensor. 00 will appear in the timer display. The 0 on the right will flash. Enter the tens first and then the units. ^ Touch the number on the numerical keypad which corresponds to the tens position (1 in this case).
Hours Whole hours are set by touching the relevant number on the numerical keypad. Half hours are set by touching the area between the relevant two numbers. Example: You want to set 2 hours 30 minutes. ^ Switch the hob on. ^ Touch the m sensor. 00 will appear in the timer display.
To change the minute minder time ^ Touch the m sensor. ^ Set the time you want, as described above. To delete the minute minder time ^ Touch the m sensor until 00 appears in the timer display.
To switch a cooking zone off automatically You can set a time at the end of which a cooking zone will switch off automatically. All the cooking zones can be programmed at the same time.
To use both timer functions at the same time The minute minder and automatic switch-off functions can be used at the same time. If you have programmed in one or more switch-off times, and would like t.
Safety lock / System lock Keep children away from the hob for their own safety. Your appliance is equipped with a safety lock to prevent the hob and the cooking zones being switched on or any settings being altered. The safety lock is set with the hob switched on.
Activating Three-finger operation (standard default setting) ^ Touch the $ sensor and the sensors for selecting both right-hand cooking zones at the same time until the safety lock indicator lights up and LC appears in the timer display. The safety lock indicator and LC will go out after a short while.
Stop and Go Your appliance has a Stop and Go feature which, when activated, reduces the power of all cooking zones in use to power level 1. When Stop and Go is activated, the cooking zone power levels and the setting of the timer cannot be altered and the hob can only be switched off.
Safety switch-off Safety switch-off with an over-long cooking time If one of the cooking zones is heated for an unusually long period of time (see chart) and the power level is not altered, the hob will switch itself off automatically and the relevant residual heat indicator will light up.
Overheating protection All the induction coils and the cooling elements for the electronics are fitted with an overheating protection mechanism. Before the induction coils or cooling elements get too .
For Miele branded cleaning and conditioning products see "Optional accessories". , Do not use a steam cleaning appliance to clean this appliance. The steam could reach electrical components and cause a short circuit. The appliance should be cleaned after each use.
Do not use washing-up liquid to clean the ceramic surface. Washing-up liquid will not remove all soiling and deposits. It will form an invisible coating which will cause permanent discolouration of the ceramic surface. Clean the hob regularly with a suitable ceramic hob cleaner.
You can change the default settings of the programme options (see chart). Several settings can be altered in succession. After selecting programming mode, P (Programme) and S (Status) will appear in the timer display. An additional indicator will appear at the rear left.
To save settings ^ Touch the s sensor until all the displays go out. To not save settings ^ Touch the $ sensor until all the displays go out. Programming 47.
Programme* Status** Setting P0 0 Demonstration mode and factory default settings S 0 Demonstration mode on (after the hob is switched on, " dE " will appear in the timer display for a few seconds). S1 Demonstration mode off S 9 Factory default settings reinstated P0 2 Power level range S0 9 power levels (1, 2, 3 .
Programme* Status** Setting P0 6 Safety lock S 0 One-finger locking using $ S1 Three-finger locking by touching $ and the sensors for selecting the right-hand cooking zones at the same time P0 7 Syste.
With the help of the following notes, minor faults in the performance of the appliance, some of which may result from incorrect operation can be put right without contacting the Service Department.
Problem Possible cause Remedy The ß symbol flashes alternately with the power setting selected in one of the cooking zones. There is no pan on the cooking zone, or the pan is unsuitable. Use a suitable pan (see "Pans"). After the hob is switched on " LC " appears in the timer display for a few seconds.
Problem Possible cause Remedy The hob switches off while it is in use and an F flashes in the timer display. One or more of the sensors have been covered, e.g. by finger contact, food boiling over or by an object such as an oven glove. Clean the control panel or remove the obstruction (see "Safety switch-off").
Problem Possible cause Remedy FE flashes alternately with numbers in the timer display. FE 44 The overheating protection mechanism has triggered. See "Overheating protection". FE 47 The fan is either blocked or faulty. Make sure it has not been blocked by something like a fork.
Miele offer a comprehensive range of useful accessories as well as cleaning and conditioning products for your Miele appliances. These can be ordered online at: or from Miele (see back cover for contact details) Pans Miele offer a wide range of pans which are perfect for Miele hobs.
Miele | home system The Miele { home system allows communication-enabled appliances to send operating and status information to a display appliance via the household electrical supply system (Powerline Technology). SuperVision appliances can display status information from other domestic appliances.
Miele | home a Communication enabled appliances (examples) b Communication module c SuperVision appliance d Electrical supply (Powerline) e Miele | home Gateway f WLAN) Router Possible connections (op.
Con | ctivity a Communication module XKM 2000 DA b Communication module XKM 2100 KM c Electrical supply (Powerline) Optional accessories 57.
Signing on the hob If you want to sign the hob – on to the Miele { home system, first prepare the signing on procedure on the master appliance (see the "Miele | home" fitting and installat.
Signing off the hob If you want to sign off from the Miele { home system, first prepare the signing off procedure on the master appliance (see the "Miele | home" fitting and installation instructions). ^ With the hob switched off, touch the s and $ sensors at the same time until the safety lock indicator light flashes.
The appliance must only be installed and connected to the electricity supply by a suitably qualified and competent person in strict accordance with current national and local safety regulations. Fit the wall units and extractor hood before fitting the hob to avoid damaging the appliance.
Safety distance above the appliance A minimum safety distance must be maintained between the appliance and the cooker hood above it. See the cooker hood manufacturer’s operating and installation instructions for details.
Safety distances to the sides and back of the hob Ideally the hob should be installed with plenty of space on either side. There may be a wall at the rear or a tall unit or wall on one side (right or left) (see illustrations). a Minimum distance of 50 mm between the back of the worktop cut-out and the rear edge of the worktop.
Safety distances underneath the hob To ensure sufficient ventilation to the hob, a certain gap must be left between the underside of the hob and any oven, interim shelf or drawer. The minimum gap between the underside of the hob and – the top of an oven is 15 mm .
Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e.
Seal between the hob and the worktop The sealing strip under the edge of the top part of the appliance provides a sufficient seal for the worktop. The hob must not be sealed with sealant (e.g. silicone). This could result in damage to the hob or the worktop if the hob ever needs to be removed for servicing.
Building-in dimensions KM 6316 a Front b Casing depth c Connection for Miele | home d Mains connection box The mains connection cable (1440 mm long) is supplied separately.
KM 6321 a Front b Casing depth c Connection for Miele | home d Mains connection box The mains connection cable (1440 mm long) is supplied separately. Hob with frame or bevelled edge 67.
Installing the hob Preparing the worktop ^ Make the worktop cut-out according to the dimensions given in the building-in diagram. Remember to maintain the minimum safety distances (see "Safety instructions for installation"). ^ Seal the cut surfaces with a suitable heat-resistant sealant to avoid swelling caused by moisture.
Building-in dimensions KM 6319 a Front b Casing depth c Connection for Miele | home d Stepped cut-out for granite or marble worktops e Mains connection box The mains connection cable (1440 mm long) is supplied separately. Please take careful note of the detailed diagrams for the cut-out dimensions in granite and marble worktops.
Installing the hob Flush fit hobs are only suitable for installation in granite, marble, tiled or solid wood worktops. When using a worktop made from any other material, please check first with the worktop manufacturer that it is suitable for installing a flush fit hob.
Granite and marble worktops Preparing the worktop a Worktop b Hob c Gap As the ceramic glass and the worktop cut-out have a certain dimensional tolerance, the size of gap c can vary (min. 1 mm). ^ Make the worktop cut-out as shown in "Building-in dimensions".
Solid wood, tiled and glass worktops Preparing the worktop a Worktop b Hob c Gap d Wooden frame 13 mm (to be provided on site) As the ceramic glass and the worktop cut-out have a certain dimensional tolerance, the size of gap c can vary (min. 1 mm). ^ Make the worktop cut-out as shown in "Building-in dimensions".
All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with current local and national safety regulations (BS 7671 in the UK). Installation, repairs and other work by unqualified persons could be dangerous.
The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system, which complies with current local and national safety regulations.
In the event of any faults which you cannot remedy yourself, please contact: – your Miele dealer, or – Miele (see back cover for contact details). Please note that telephone calls may be monitored and recorded for training purposes (UK only). When contacting your Dealer or Miele, please quote the model and serial number of your appliance.
Alteration rights reserved / 5012 M.-Nr. 09 549 430 / 00.
デバイスMiele km 6316の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Miele km 6316をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiele km 6316の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miele km 6316の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miele km 6316で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miele km 6316を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiele km 6316の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miele km 6316に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiele km 6316デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
