MieleメーカーTOUCHTRONIC G 694 SCの使用説明書/サービス説明書
ページ先へ移動 of 56
Oper ating instr uctions T ouchtronic G 694 SC G 894 SC T o prevent accidents and machine damage, read these instructions bef ore installation or use. UV M.
IMPOR T ANT SAFETY INSTR UCTIONS CONSIGNES DE SÉCURITÉ Caring f or the en vir onment Energy saving washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Guide to the dishwasher W ash cabinet . . . . . .
Operation Adding detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Running the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Program sequence indicator (16) .
W ARNING – When using y our dishwasher , follo w basic precautions, including the f ollowing: Read all instructions bef ore installa - tion or use of the dishwasher to pre - vent injury and machine damage. The manufacturer cannot be held r e - sponsible for damage or injur y caused by improper use of this ap- pliance.
This equipment is not designed for maritime use or for use in mobile installations such as caravans or air - craft. However , under certain conditions it may be possible for an installation in these applications. Please contact the nearest Miele dealer or the Miele T ech - nical Service Department with specific requir ements.
When loading tableware, place sharp items away from the door seal to prevent damage to the seal. Load knives pointing downwards to prevent injuries. Only use detergents and rinse aids recommended for r esidential dish - washers. Keep all detergents and rinse aids out of the reach of childr en.
A VER TISSEMENT – A u moment d’utiliser v otre lave-v aisselle, prenez des précautions essentielles, dont : Lisez attentivement l’ensemble des consignes av ant d’installer ou d’utiliser le lave-v aisselle afin de prévenir les blessures et éviter d’endommager l’appareil.
Installation L ’installation et les réparations de - vraient être ef fectuées uniquement par un technicien de service autorisé Miele. Les travaux effectués par des personnes non qualifiées peuvent s’avérer danger eux et rendre nulle la garantie.
Utilisation N’utilisez le lave-vaisselle que lorsque tous les panneaux sont bien en place. Ne jouez pas avec les commandes. Afin de diminuer le risque de bles - sures, ne laissez pas les enfants jouer près de l’appareil ni monter de - dans ou dessus.
Energy sa ving washing This dishwasher is exceptionally eco - nomical in the use of water and electric - ity . For best results follow these tips: ^ For lowest energy consumption and the gentlest washing of china and crystal, connect the dishwasher to a cold water source.
W ash cabinet 1 Upper spray arm (not visible) 2 Cutlery tray 3 Upper basket 4 W ater feed for middle spray ar m 5 Middle spray arm 6 Lower spray arm 7 Four height adjustable feet 8 T riple Filter Syst.
Contr ol panel 13 "On/Off" button 14 Program list / indicators 15 Check/Refill indicators 16 Program sequence display 17 Delay start display 18 "Start/Stop" button 19 "Delay s.
T o open the door ^ Press the r elease catch inside the door grip. If the door is opened during operation, the dishwasher will stop running. Once the door is closed the program will r e- start. T o close the door ^ Push the baskets in. ^ Lift the door and push until it clicks into position.
W ater softener T o achieve good cleaning results, the dishwasher needs soft water . Hard water results in calcium deposits on dishware and in the dishwasher . If your tap water hardness is above 8 gr/gal (140 ppm), the water should be softened. This takes place automati - cally in the unit’ s integrated water soft - ener .
Programming the water softener Y our water hardness level must be pr o- grammed into the dishwasher using the buttons on the control panel. The programming can be cancelled and restarted at any time by tur ning the dishwasher off with the "On/Of f" button (13).
Checking the pr ogrammed water har dness ^ Make sure the dishwasher is turned off. ^ Press and hold the "T op Solo" (20) and "Start/Stop" (18) buttons and at the same time turn on the dishwasher with the "On/Off" button (13).
Filling the salt reservoir If your water hardness level is gr eater than 8 gr/gal, the salt reservoir should be filled before the first use and when the "Salt" indicator lights. Only use water softener salt specially formulated for dishwashers.
Salt indicator When the salt reservoir is empty , the "Salt-PC" indicator will light, indicating that it should be refilled with r eactiva - tion salt. After the reservoir has been filled, the water softener is automatically reacti- vated the next time the dishwasher is started.
Rinse aid Rinse aid is recommended to pr event spotting on dishes and glassware. , Filling the rinse aid reservoir with detergent will damage the reservoir . Only pour rinse aid formulated for residential dishwashers into the reservoir . Adding rinse aid ^ Add rinse aid before the first use and whenever the "Rise aid" indicator lights.
Adjusting the dosage The dosage selector is preset to 3. This dispenses approximately 3 ml of rinse aid per program. It can be adjusted from 1 to 6. ^ Use a higher setting if spots appear on dry glassware. ^ Use a lower setting if streaking ap- pears on dishes or glasses.
, Do not wash items soiled with ash, sand, wax, grease or paint in the dishwasher . Ash and sand do not dissolve and will be distributed through out the in - side of the dishwasher . W ax, grease and paint will cause permanent discoloration or damage to the dishwasher .
Items not recommended f or dishwashing – Cutlery with wooden handles. – Wooden cutting boar ds. – Glued items such as old knives with handles glued together around the shank of the blade. – Hand made craft items, antique, metal trimmed or decorative glass - ware.
Cutlery tray (SC units) The removable cutlery tray makes un- loading flatware easy . Simply carr y the cutlery tray to where the flatware is stored and put the entir e basket away in one trip. For easier unloading cutler y should be grouped in zones, one for knives, one for forks, one for spoons, etc.
Upper basket Adjusting the upper basket On select models, the upper basket can be raised or lowered to accommo - date tall items. ^ Slide out the upper basket. ^ Pull up the levers at the sides of the upper basket and adjust the basket height. ^ Release the levers and the basket will lock in place.
Adjustable cup rac ks Raise the rack to make room for tall glasses. Lower it to double stack smaller pieces. Coffee bar T o allow water to run off the bottom of coffee mugs, place slanted on top of the coffee bar . The bar can also be used to separate two rows of glasses.
Lower basket For larger and heavier items such as plates, serving platters, sauce pans, bowls. Dishwasher with cutlery tray Dishwasher with cutlery basket Height limit The guide at the front of the upper bas- ket determines the maximum height for items placed in the lower basket so that the middle spray arm is not blocked.
V arious removable inserts are available for the lower basket to accomodate spe - cial items to be washed. Removing an insert ^ T o remove an insert, gently pull up on the handle. Inser ting an insert ^ Slid the hitches of the inset under the vertical struts of the lower basket.
Foldable spike insert A highly flexible design holds tableware securely . It can be folded out of the way for pots, pans and other large items. This insert secures plates and platters. Foldable spikes T wo rows of spikes can be folded down, to create mor e room for larger dishware e.
PlateGuar d Plus inser t A unique design cradles plates at 3 points and can be used for washing cups, glasses, plates, bowls and pots. ^ Hook the PlateGuard Plus insert into the left half of the lower basket, the area marked in white. V ase / Bottle holder The bottle holder e.
Additional inserts for the upper and lower baskets may be purchased from your Miele dealer or the Miele T echnical Service Depar tment. V ase / Bottle holder to wash milk or baby bottles attaches to t.
Adding deter gent , Dishwasher detergents contain irritant and corrosive ingr edients. Keep children away fr om detergent. Do not fill the detergent dispenser until you are r eady to star t the dish - washer . Only use powder detergents or tab - lets formulated for residential dish - washers.
Running the dishwasher ^ Make sure the spray arms are not blocked. ^ Close the door . ^ T urn on the dishwasher . ^ Press the "On/Of f" button (13). The "Start/Stop" indicator (18) will flash and a program indicator will light. ^ Select a wash program using the pr o- gram selection buttons (21).
At the end of a pr ogram The "End" indicator will light and 0 will appear in the delay start display when the program has finished. ^ T urn off the dishwasher . The "Start/Stop" (18) indicator will go out. ^ Open the dishwasher door slightly to allow the dishes to cool before un - loading.
Pr ogram guide Program When to use Program cycle Pre- wash 12 Main wash Interim rinse 12 Final rinse Dry- ing Pots & Pans for heavily soiled pots and pans with dried on f ood Main wash temperature.
Additional f eatures "T op Solo" (20) Using "T op Solo" will save water and energy . This program is r ecommended when there is only a small load to clean. "T op Solo" can be selected with all pro- grams. With this feature, water is dir ected only to the top and middle spray ar ms in the dishwasher .
"Delay start" (19) The start time of a program can be de- layed from 1 to 9 hours. The delay start is set in one hour steps. When using delay start, make sure the detergent compartment is dr y before adding detergent. Wipe dry if necessary .
T o star t a program bef ore the delay star t period has elapsed: ^ Press and hold the "Start/Stop" (18) button for at least one second. The delay start display (17) will go out. The "Start/Stop" (18) indicator will flash. ^ Select "T op Solo" again, if needed.
Extended drying If desired drying results ar e not consis - tently achieved, the turbother mic cool - ing fan can be programmed to run an extra 14 minutes at the end of each program. The "Extended drying" feature can also be activated to prevent condensation from collecting on the steam deflector .
With the aid of the following guide, minor problems can be fixed without a service call. , Repairs should only be carried out by a qualified and trained person in ac - cordance with local and national safety r egulations. Unauthorized r epairs could cause personal injury or machine damage.
What if … P ossible fault Fix the "Intake/Drain" indi - cator flashes and the program stops? W ater intake error – T urn off the dishwasher before fixing the pr ob - lem. – Open the water valve. – Clean the water intake filter , see maintenance instructions.
What if … P ossible fault Fix the "End", "Star t/Stop" and "T op Solo" indica - tors flash at the same time at the end of a pro - gram? There may be a technical fault. – Press the "Start/Stop" button. – T urn off the dishwasher .
What if … P ossible fault Fix dishes are not clean? The dishes were not loaded correctly . See, "Loading the dish - washer". The program was not powerful enough. Select a more intensive program see, "Pr ogram guide". Not enough detergent was used.
What if … P ossible fault Fix glasses are dull and dis - colored and film cannot be wiped off? Glasses are not dish - washer safe. There is no r emedy . Only wash dishwasher safe glasses. plastic items are discol - ored? Natural dyes e. g. from vegetables may be the cause.
In the event of a fault which you cannot correct yourself please contact: – Y our Miele Dealer or – The Miele T echnical Service Depar t - ment. USA 1-800-999-1360 techserv@mieleusa.com CDN 1-800-565-6435 service@miele.ca When contacting the Miele T echnical Service Department, please quote the model and serial number of your appli- ance.
T o transport the dishwasher , e. g. when moving to a new home, note the follow - ing: – Empty the dishwasher . – Secure any loose parts, e. g. hoses, cables, cutlery baskets. – T ransport the dishwasher in the up - right position. If unavoidable it may be transpor ted on its back.
46.
User Maintenance Instr uctions T o prevent accidents and machine damage, read these instructions bef ore installation or use..
T riple filter system The triple filter system in the base of the wash cabinet prevents food fr om being redeposited on dishes. It also pr otects the circulation pump fr om damage caused by foreign objects (e.g. br oken glass, bones). The filter system should be cleaned ev - ery 4 - 6 months or whenever a foreign object is trapped.
T o clean the underside of the filter , the flap must be opened: ^ Pull back the yellow clip. ^ Rinse all parts under running water . Scrub with a nylon brush if neces- sary . ^ Close the flap so that the clip en- gages. ^ Return the filter so it lies flat in the base of the wash cabinet.
Cleaning the spra y arms Sometimes particles of food get stuck in the spray arm jets. The spray ar ms should be inspected and cleaned ever y 4 - 6 months. ^ T urn off the dishwasher before clean - ing. Remove the spray arms as follows: ^ Remove the cutlery tray (if present).
Cleaning the wash cabinet Generally , the wash cabinet is self cleaning if the correct amount of dish - washer detergent is used. The wash cabinet can be cleaned with a dishwasher cleaner such as Dis Cleaner available from your Miele dealer or the Miele T echnical Service Department.
Cleaning the water inlet filter A filter is incorporated in the intake hose attached to the dishwasher’ s shut off valve. If your water is har d, or the pipes contain sediment, this filter may clog and prevent enough water fr om entering the wash cabinet.
Cleaning the drain pump and non-return v alve If the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ T urn off the dishwasher . ^ Remove the triple filter (see "Cleaning the filter in the wash cabinet").
54.
55.
M.-Nr . 05 431 271 / V00 M.-Nr . 05 431 271 / V00 Alterations rights reserved / (G 694 / G 894 Plus) / 1403 This bio-friendly paper was bleached without the use of chlorine.
デバイスMiele TOUCHTRONIC G 694 SCの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Miele TOUCHTRONIC G 694 SCをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiele TOUCHTRONIC G 694 SCの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miele TOUCHTRONIC G 694 SCの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miele TOUCHTRONIC G 694 SCで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miele TOUCHTRONIC G 694 SCを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiele TOUCHTRONIC G 694 SCの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miele TOUCHTRONIC G 694 SCに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiele TOUCHTRONIC G 694 SCデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
