MiLANメーカーMIL-S501MT-15の使用説明書/サービス説明書
ページ先へ移動 of 20
1 MIL-S501xx Series 5x 10/100 N-Way RJ-45 Ports plus One 100Base-FX fiber Port MIL-S501ST with ST connector (2km) MIL-S501SC with SC connector (2km) MIL-S501SC-15 with SC connector (15km) MIL-S501SC-4.
2 COPYRIGHT 2000 ALL RIGHTS RESERVED. First Edition. Printed in Taiwan. All trademarks are the properties of their respective owners. No portion of this document may be reproduced, altered, adapted or translated without the prior written approval.
3 C ontents 1. Introduction …….………………………….……….… 4 Features ………………………………………….. ….….…… 5 Package Contents ……………………….. ……………….... 6 2. Hardware Description ………………….
4 1. Introduction Welcome to the World of Mini-Networking. In the modern business societ y , communication and sharing information is crucial. Computer networks have proven to be one of the fastest modes of communication. The MIL-S501xx is a compact desktop size switch that is an ideal solution for small office or home office network user.
5 These fiber connectors are S T , SC multi-mode, SC single-mode, MT-RJ, and VF-45. The fiber port can be used to connect to a remote site up to 2 kilometers (SC single-mode up to 70 kilometers) awa y.
6 MIL- S501XX Rubber Feet DC power A dapter User’s Manual Warranty Card Figure1-2. Package Contents Compare the contents of your MIL-S501xx package with the standard checklist above . If any item is missing or damaged, please contact your local dealer for service.
7 2. Hardware Description This Section mainly describes the hardware of the MIL-S501xx. The MIL-S501xx is a compact palm size switch (6.5 inches) with 5x 10/100 N-Way UTP switch ports plus one 100Baes-FX fiber port. The physical dimensions of the MIL-S501xx are: 165mm x 100mm x 24mm 6.
8 LED Indicators The following table provides descriptions of the LED statuses and meaning. On Green The port is successfully connecting with the device. Blinks The port is receiving or transmitting data. LNK / ACT Off No device attached. On Yellow The port is operating in Full-duplex mode.
9 Rear Panel The Rear Panel of the MIL-S501xx consists of 5x 10/100 N-Way UTP switch ports, Uplink Port, one 100Base-FX fiber port, 1 DIP- switch to select fiber port full-duplex or half-duplex mode, and DC power connector. There are five types of fiber connectors available for the convenience of your connectivit y .
10 MIL-S501xx with ST Connector Figure 2-4. The Rear Panel of the MIL-S501xx with ST Connector MIL-S501xx with MT-RJ Connector Figure 2-5. The Rear Panel of the MIL-S501xx with MT-RJ Connector MIL-S501xx with VF-45 Connector Figure 2-6.
11 n RJ-45 Ports: Five 10/100 N-Way auto-sensing for 10Base-T or 100Baes-TX connections. n Uplink Port: One uplink port to cascade to a hub or switch, with the maximum distance between the switch to another device is 100 meters. n 100Base-FX Fiber Port: There are 5 types of fiber connectors available for the MIL-S501xx as shown above.
12 3. Network Application This section provides you a few samples of network topology in which the Switch is used. In general, the MIL-S501xx is designed to be used as a desktop or segment switch. The Switch automatically learns node addresses, which are subsequently used to filter and forward all traffic based on the destination address.
13 Collapsed Backbone Application You can use Uplink port of the MIL-S501xx to connect with another hub or switch t o interconnect each of your small-switched workgroups to form a larger switched network . You can also use fiber ports to connect switches.
14 4. Trouble Shooting The Switch can be easily monitored through panel indicators to assist in identifying problems. This section describes common problems you may encounter and where you can find possible solutions. n Diagnosing LED Indicator If L ink indicator does not light up after making a connection.
15 n Cabling A. RJ-45 ports: Use unshielded twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ-45 connections: Category3, 4 or 5 cable for 10Mbps connections or Category 5 cable for 100Mbps connections. Also be sure that the length of any twisted-pair connection does not exceed 100 meters (328 feet).
16 5. Technical Specification Specification Standards Compliance IEEE 802.3 10Base-T Ethernet, IEEE 802.3u 100Base-TX/FX Fast Ethernet ANSI/IEEE 802.3 N-Way auto-negotiation Protocol CSMA/CD Max Forwa.
17 A ppendix What is Switch Ethernet ? With a high-speed backplane, it is possible to have all ports communicating at wire speed with minimal latency and low packet loss A-1. 100Base-T Technology Review The 100BaseT standard retains 10BaseT's critical 100-meter maximum cable length between the hub and desktop.
18 *100BaseT4 for four-pair voice and data grade Category 3,4 or 5 UTP *100BaseFX for 2-strand multimode fiber Media Access Control (MAC) Layer The MAC layer is based on the same CSMA/CD protocol as 10Mbps Ethernet. The only difference is that it runs 10times faster.
19 A switch is an intranetwork device designed to increase performance through LAN segmentation. Switching uses microsegmentation to isolate traffic. Upon arrival at the hub, a packet's destination address is read and the packet is sent directly to the relevant port - not to all ports, as it would be with a repeater.
20 Store-and-Forward Switching Store-and-forward switching is the best choice to keep the network effective and reliable. Store-and-forward provides excellent error-checking function. For example, CRC, runt and collision filter. Store-and-Forward reads the entire data packet, verifies the packet and sends it to the destination port.
デバイスMiLAN MIL-S501MT-15の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
MiLAN MIL-S501MT-15をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiLAN MIL-S501MT-15の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。MiLAN MIL-S501MT-15の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。MiLAN MIL-S501MT-15で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
MiLAN MIL-S501MT-15を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiLAN MIL-S501MT-15の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、MiLAN MIL-S501MT-15に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiLAN MIL-S501MT-15デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
