MiLANメーカーMIL-S8000Gの使用説明書/サービス説明書
ページ先へ移動 of 22
8-Port Gigabit Switch MIL-S8000G User Guide Eight Auto-negotiation 10/100/1000Mbps Gigabit Ethernet RJ-45 Ports. Each port with Auto MDI/MDIX..
Regulatory Approval - FCC Class A - UL 1950 - CSA C22.2 Number 950 - EN60950 - CE EN55022 Class A EN55024 Canadian EMI Notice This Class A digital apparatus meet s all the requirements of the Canadian Interference-Causin g Equipment Regulations.
1 T able of Content s 1. Introduction Features Package Contents 2. Hardware Description Front Panel LED Indicators Rear Panel 3. Installation Desktop Installation Rack-mount Installation Power On 4. Network Application Backbone Switch 5. Network Configuration Login to the Console Interface 5.
2 1. Introduction Gigabit Ethernet over copper technology is a cost-effective way for network equipment to be upgraded from Fast Ethernet to Gigabit speeds without the use of expensive fiber opti cs cabling. Gigabit networks create high-speed backbone connections bet ween switches, servers, databases and end stations.
3 Package Content s MIL-S8000G 8 port Gigabit switch Power Cord Four Adhesive Rubber Feet User’s Manual W arranty Card Compare the content s of your MIL-S8000G package with the standard checklist above. If any it em is missing or damaged, please contact your local deal er for service.
4 2. Hardware Description Front Panel The Front Panel of the 8-Port Gigabi t Switch consists of eight auto- negotiation 10/100/1000Mbps Ethernet RJ-45 connectors, supporting automatic MDI/MDIX, and four LED- indicators (1000M, 100M, LK/ACT , FUL/COL) for each Gigabit port.
5 LED S t atus Description Green Power On Power Off Power is not connected Green The port is operating at the speed of 1000Mbps. 1000M Off No device attached or in 10/100Mbp s mode Green The port is operating at the speed of 100Mbps. 100M Off No device attached or in 10Mbp s mode Green The port is connecting with the device.
6 3. Inst allation Desktop Inst allation Set the switch on a sufficiently large flat sp ace with a power outlet nearby . The surface should be clean, smooth, level, and sturdy . Make sure there is enough clearance around the switch to allow attachment of cables, power cord and air circulation.
7 Figur e 3-2. Attach mounting br ackets with scr ews B. After att aching both mounting brackets, position the MIL-S8000G switch in the rack by lining up the holes in the brackets with the appropriate holes on the rack. Secure the switch to the rack with a screwdriver and the rack-mounting screws.
8 4. Network Application The MIL-S8000G Switch can be used connect servers, switches, workstations, and PCs (a Gigabit 1000Base-T NIC is required for PC installation) to each other by connecting these devices directly to the Switch.
9 Workgroup A Workgroup B Figur e 4-1. An example of a ne twork connection, with the MIL-S8000G Switch acting as the cor e switch. This switch is an ideal solution for backbone connectivity . In the above example, servers, department swit ches, and workst ations are directly connected to the core swit ch, the MIL-S8000G Switch.
10 5. Network Configuration The Console port is a female DB-9 connector that enables a connection to a PC or terminal for monito ring and configuring the MIL-S8000G Switch. Use the supplied RS-232 cable with a male DB-9 connector to connect a terminal or PC to the Console port.
11 Login to the Console Interface When the connection between Switch and PC is finished, turn on the PC and run a terminal emulation program or Hyper T erminal . Configure the communication parameters to ma tch t he following default characteristics of the console port: Figur e 5-2.
12 5.2 Port Configuration Figur e 5-4. The Port Configuration menu Select each port to change the status , toggle the Enable / Disable field and enter the appropriate value in the Flow Control field.
13 5.3 Mirror Configuration Figur e 5-5. The Device Configuration Setup menu Figur e 5-6. The Device Configuration Setup menu By enabling port mirroring, the source port will be forwarded to the target port. Select either Enable or Disable by using the <Backspace> key.
14 5.4 VLAN Configuration Figur e 5-7. The VLAN Configuration menu Assigning physical ports within a work group is a simple and common method of defining a virtual work group – VLAN. It delivers the benefit of broadcast control and simplifies config uration for the network manager .
15 5.5 VLAN Setup Figur e 5-8. The VLAN Setup menu Select the VLAN entry to Enable or Disable the VLAN group. Use the <Backsp ace> key to Enable (add) or Disable (remove) ports in the VLAN group.
16 5.7 Miscellaneous Configuration Figur e 5-10. The Misc. Configuration menu Select each port to change the status , toggle the Enable / Disable field and enter the appropriate value in the Aging T ime field.
17 6. T roubleshooting This troubleshooting section is intended to help solve many common problems that might occur when inst alling the MIL-S8000G . The switch can be easily monitored through panel indicators to assist in identifying problems.
18 7. MIL-S8000G T echnical S pecifications St andards Compliance IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet IEEE 802.3ab 1000Base-T Gigabit Ethernet ANSI/IEEE 802.
.
Part No. 90000404_A.
デバイスMiLAN MIL-S8000Gの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
MiLAN MIL-S8000Gをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiLAN MIL-S8000Gの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。MiLAN MIL-S8000Gの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。MiLAN MIL-S8000Gで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
MiLAN MIL-S8000Gを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiLAN MIL-S8000Gの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、MiLAN MIL-S8000Gに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiLAN MIL-S8000Gデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
