Miller ElectricメーカーHWY-210の使用説明書/サービス説明書
ページ先へ移動 of 20
Visit our website at w ww .Mi llerWelds.co m Descrip tio n T wo-Wheel Trailer For Small Engine- Driven Welding Generators OM -699 189 553 February 1998 HWY -210 & OFR-210.
Miller Electric manufactures a full line of welders and welding related equipment. For information on other quality Miller products, contact your local Miller distributor to receive the latest full line catalog or individual catalog sheets. T o locate your nearest distributor call 1-800-4-A-Miller .
safety_trailer 10/96 TRAILER TOWING SAFETY PRECAUTIONS In trailer towing, as in most driving situations, exposure to certain hazards occurs. T railer towing is safe when precautions are taken. The following safety information is only a summary of the more complete information found in the Safety Standards listed at the end of these precautions.
safety_trailer 10/96 INCORRECT SIZE OR RA TING OF HITCH can cause trailer to break loose from towing vehicle. 1. Be sure towing vehicle hitch is correct type, size, and rating to match coupler . 2. Be sure the hitch is properly installed onto towing vehicle.
safety_trailer 10/96 LOOSE OR INCORRECT HARDWARE AND F ASTENERS can cause injury and damage. 1. Periodically double-check all nuts and bolts for tightness and condition. 2. If necessary , always replace any fastener with one of equal size, grade, and type.
.
OM-699 Page 1 SECTION 1 − ASSEMBL Y SAFETY PRECAUTIONS trail_safety 2/98 1-1. Symbol Usage Means W arning! W atch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols. Y Marks a special safety message.
OM-699 Page 2 2-2. Overall Dimensions ST-802 067 Inches Millimeters A 18-1/2 470 B 10 254 C 36-3/4 933 D 59 1499 E 94 2388 A B C D E.
OM-699 Page 3 SECTION 3 − ASSEMBL Y All directions are given as facing the towing vehicle. The word “front” means the hitch end of the trailer . NOTE 3-1. Assembling T railer ST-802 073 Y Use adequate blocks or lifting device to support frame while installing parts.
OM-699 Page 4 3-2. Installing Hitch And Safety Chains T ools Needed: 9/16, 3/4 in 1 1/16, 3/4 in ST-802 067 / Ref. ST -802 073 Y Use adequate blocks or lifting de- vice to support frame while instal- ling parts. Y Support trailer with jack. Block wheels.
OM-699 Page 5 3-3. Installing Optional Light Kit ST-802 074 Y Support trailer with jack. Block wheels. 1 Wiring Harness White Ground Lead Secure ground lead ring terminal to the chain bracket using 1/4-20 x 3/4 hardware. 2 Grommet Locate holes for routing wire near each tail- light.
OM-699 Page 6 3-4. Installing Wiring Harness T ab Connectors Disconnect vehicle wiring harness plug from trailer wiring connector before beginning installation. Use wiring harness tab connectors only with insulated wires. NOTE 1 Connector 2 Ru n Wire 3 T ap Wire Place unstripped run wire in slotted channel.
OM-699 Page 7 3-6. Maintenance Do not use trailer if any part is damaged or not working properly . When performing maintenance, check trailer for worn, damaged, or non-working parts. Check for free rotation of assemblies mounted on bushings or bearings.
OM-699 Page 8 3-7. T orquing Wheel Bearings Ref. ST-800 441-A Y Loss of control hazard. T o prevent injury and damage, check and repack wheel bearings once a year or ev - ery 12,000 miles (19,500 km), whichever comes first. Y Use proper equipment to lift and support unit.
OM-699 Page 9 SECTION 4 − P ARTS LIST ST -802 076 . Hardware is common and not available unless listed. 7 8 9 10 11 6 14 3 5 6 2 13 12 1 4 Figure 4-1. Complete Assembly Description Quantity Part No. Item No. Figure 4-1. Complete Assembly 1 189 588 CHAIN, safety kit 1 .
Notes.
Notes.
Notes.
Effective January 1, 1998 (Equipment with a serial number preface of “KJ” or newer) This limited warranty supersedes all previous Miller warranties and is exclusive with no other guarantees or warranties expressed or implied. LIMITED W ARRANTY − Subject to the terms and conditions below , Miller Electric Mfg.
PRINTED IN USA © 1998 Miller Electric Mfg. Co. 9/98 Miller Elect ric Mfg. Co. An Illinois T oo l W orks Comp any 1635 West Spenc er St reet Applet on, W I 54914 USA International He adquarters − US.
デバイスMiller Electric HWY-210の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Miller Electric HWY-210をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiller Electric HWY-210の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miller Electric HWY-210の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miller Electric HWY-210で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miller Electric HWY-210を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiller Electric HWY-210の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miller Electric HWY-210に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiller Electric HWY-210デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
