Miller ElectricメーカーMC-80の使用説明書/サービス説明書
ページ先へ移動 of 20
cover 5/94 – Ref. ST-800 895 PRINTED IN USA 1995 MILLER Electric Mfg. Co. Air-Cooled Plasma Arc Cutting (P AC) T orches Can Be Used For Plasma Arc Gouging (P AG) 80 Amperes, 120 V olts DC At 100% Duty Cycle Safety Interlock Devices Shut Down Power Source Hand-Held T orch Equipped With Either 25 Or 50 ft (7.
Miller Electric manufactures a full line of welders and welding related equipment. For information on other quality Miller products, contact your local Miller distributor to receive the latest full line catalog or individual catalog sheets. T o locate your nearest distributor or service agency call 1-800-4-A-Miller , or visit us at www .
sr2 1 1/92 PLASMA ARC CUTTING SAFETY PRECAUTIONS W ARNING PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJUR Y OR DEA TH. KEEP CHILDREN A W A Y . P ACEMAKER WEARERS KEEP A WA Y UNTIL CONSUL TING YOUR DOCTOR. In cutting, as in most jobs, exposure to certain hazards occurs.
sr2 1 1/92 FUMES AND GASES can be hazardous to your health. Cutting produces fumes and gases. Breathing these fumes and gases can be hazardous to your health. 1. Keep your head out of the fumes. Do not breathe the fumes. 2. If inside, ventilate the area and/or use exhaust at the arc to remove cutting fumes and gases.
OM-1592A – 5/95 EMF INFORMA TION Th e following is a quotation from the General Conclusions Section of the U.S. Congress, Office of T echnology Assessment, Biological Effects of Power Frequency Electric & Magnetic Fields – Background Paper , OT A-BP-E-53 (Washington, DC: U.
.
OM-1592 Page 1 SECTION 1 – SAFETY INFORMA TION mod1.1 2/93 Read all safety messages throughout this manual. Obey all safety messages to avoid injury . Learn the meaning of W ARNING and CAUTION. 1 Safety Alert Symbol 2 Signal Word W ARNING means possible death or serious injury can happen.
OM-1592 Page 2 Ref. ST-800 895 / Ref. ST -801 208 A B Inches Millimeters A 10-1/2 267 B 1-3/8 35 C 1-1/4 32 D 1-5/16 33 E 13-1 1/16 348 D Hand-Held T orch Machine-Held T orch C E Figure 2-1. Overall Dimensions 2-1. Duty Cycle CAUTION CUTTING LONGER THAN RA TED DUTY CYCLE can damage cutter and torch and void warranty .
OM-1592 Page 3 SECTION 3 – INST ALLA TION 3-1. Installing Hand-Held T orch ELECTRIC SHOCK can kill. • Do not touch live electrical parts. • T urn Of f cutter , and disconnect input power before installing torch. MOVING P ARTS can cause injury . • Keep away from moving parts.
OM-1592 Page 4 3-2. Installing Machine-Held T orch And Remote T rigger Pendant ELECTRIC SHOCK can kill. • Do not touch live electrical parts. • T urn Of f cutter , and disconnect input power before installing torch. MOVING P ARTS can cause injury .
OM-1592 Page 5 SECTION 4 – OPERA TING THE TORCH W ARNING ELECTRIC SHOCK can kill. • Always wear dry insulating gloves. • Insulate yourself from work and ground. • Do not touch live electrical parts. • Keep all panels and covers securely in place.
OM-1592 Page 6 CAUTION TIP AND EL ECTRO DE WEAR BEYOND RECOM MENDED V AL UES or OPERA TI ON WI THO UT TI P OR ELECT RODE can damag e torch. • Inspect cup, tip, and electrode before cutting or whenever cutting speed has been significantly reduced (see Section 5-2).
OM-1592 Page 7 Figure 4-2. Sequence Of Plasma Arc Cutting (P AC) HITTING TORCH ON A HARD SURF ACE to remove spatter can damage torch. • Do not clean torch by hitting it against a hard surface. • Hitting hard surfaces can damage torch parts and stop proper operation.
OM-1592 Page 8 SECTION 5 – MAINTENANCE & TROUBLESHOOTING ELECTRIC SHOCK can kill. • Do not touch live electrical parts. • T urn Of f cutter , and disconnect input power before inspecting, maintaining, or servicing. HOT P ARTS can cause severe burns.
OM-1592 Page 9 5-2. Checking/Replacing Cup, Tip, And Electrode CAUTION OVERTIGHTENING will strip threads. • Do not overtighten electrode, tip, and cup during assembly . • Do not cross-thread parts causing stripping. • Use care during torch assembly and parts replacement.
OM-1592 Page 10 5-3. T roubleshooting ELECTRIC SHOCK can kill. • Do not touch live electrical parts. • T urn Of f cutter , and disconnect input power before inspecting, maintaining, or servicing. HOT P ARTS can cause severe burns. • Allow cooling period before maintaining or servicing.
OM-1592 Page 1 1 SECTION 6 – P ARTS LIST Description Part No. Item No. Figure 6-1. T orch, MC-80 (Hand-Held) Quantity 1 172 385 TORCH, body assembly (consisting of) 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-1592 Page 12 Description Part No. Item No. Figure 6-3. T orch, MC-80 (Machine) Quantity 1 175 833 TORCH, body assembly (consisting of) 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 175 829 TORCH HEAD, (Includes Item 5) 1 .
Warranty Questions? Call 1-800-4-A-MILLER for your local Miller distributor. miller_warr 7/00 Y our distributor also gives you ... Service Y ou always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours. Support Need fast answers to the tough welding questions? Contact your distributor .
PRINTED IN USA 2000 Miller Electric Mfg. Co. 6/00 Miller Elect ric Mfg. Co. An I l li noi s T ool Works Com pany 1635 West Spenc er St reet Applet on, W I 54914 USA International He adquarters –.
デバイスMiller Electric MC-80の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Miller Electric MC-80をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiller Electric MC-80の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miller Electric MC-80の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miller Electric MC-80で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miller Electric MC-80を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiller Electric MC-80の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miller Electric MC-80に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiller Electric MC-80デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
