Minicom Advanced SystemsメーカーPhantomの使用説明書/サービス説明書
ページ先へ移動 of 41
International HQ Jerusalem, I srael Tel: + 972 2 535 9666 min ic om@ min ic om. co m North American HQ Linden , New Je rsey Tel: + 1 908 4862100 info.usa@m inicom.com German Europe Zurich, Sw itzerland Tel: + 41 1 455 6220 in fo .g er man @min ic om. co m Italy Rome Tel: + 39 06 8209 7902 info.
Intro duction 1-1 Chapter 1: Introduc tion The Phantom sy stem from Minicom is a CAT5 based Distributed KVM Switching sy stem for serv er manag ement. Connect up to 64 com puters in the Phantom sy stem. The sy stem can be m anaged and controlled by 1 or 2 users.
The Phant om confi guration 1-2 Features The Phantom sy stem g ives you: • C o n t r o l a n d m o n i t o r m ixed, multi- platform server env ironments o f u p to 6 3 remote c o m pu te rs f r o m.
Intro duction 1-3 The confi g uration dia g ram below shows both Remote PCI cards and Specters in the Phantom UPM s y stem . CAT5 System Cable ProL iant D L360 9.1 - GB 10 k ULTRA2 SCSI 9.1 - GB 10k ULTRA 2 SCSI ProL iant D L360 9.1 - GB 10 k ULTRA2 SCSI 9.
The Phant om confi guration 1-4 The configuration diagram below shows both Remote PCI cards and Specters in the Phantom RackManag er UPM s y stem . CAT5 System cable ProLiant DL360 9.1 - GB 10k ULTRA2 SCSI 9.1 - GB 10k ULTRA2 SCSI ProLiant DL360 9.1 - GB 10k ULTRA2 SCSI 9.
OSD T echnol ogy 1 - 5 OSD T echnology The Phantom sy stem superim poses a menu on the Manag er position computer screen. This On- Screen-D isplay (OSD) consists of three sections. From the OSD, y ou activate v arious functions discussed in the Operating guide.
The OSD f unctions 2-1 Chapter 2: The OSD functions The Phantom sy stem is controlled and m onitored through an On- Screen-D isplay (OSD) on the Manager screen. When the Phantom Manag er is the UPM you can also use Minicom ’s Control software or equivalent software.
The hotkey functi ons 2-2 Selecting a Computer To select a computer: 1. Navigate to the desired com puter with the Up and Down A rro w keys . Or Type the computer num ber. I t will appear in the “SELECT COMPUTER” line. See Figure 2- 1. 2. Press Enter .
The OSD functions 2-3 Move Label - F1 Position the Confirmation label – Fig ure 2-2 abov e – anywhere on the screen. To position the label: 1. Navigate to the desired com puter using the Up and Down arrow k eys. 2. Press F1 . The selected screen im age and I dentification label will appear.
The hotkey functi ons 2-4 1. Navig ate to the first character in the sequence. 2. Press and hold the Spacebar down until y ou erase the sequence. Saving changes To save all editing chang es and return to the Select Com puter window: Press Esc .
The OSD f unctions 2-5 Column Function Numbers Com puter num bers in groups of 8 SCN Scanning tim e period DSP Confirmation label display time KB Keyboard setting , either PS or Unix MS Mouse ty pe OU.
The hotkey f unctions 2-6 Removing a computer from the scanning sequence To remov e a computer from the scanning sequence: 1. Type 000 in the SCN column. 2. Press Esc . Const antly displa y i ng the Confirmation label To constantly display the com puter Confirm ation label: 1.
The OSD f unctions 2-7 Scanning Computers – F4 You scan com puters from the Select Com puter window. To start scanning: Press F4 . During scanning a Confirmation label appears, showing which Remote com puter is presently displayed.
The OSD functions 2 -8 Skipping out unconnected or switched off computers - F6 When navigating through the list of computers, you can skip out the unconnected or switched off computers. You do this with Autoskip. By default, Autoskip is activated. To activate or deactivate Autoskip: In the Setup window (F3), press F6 .
Passw ord protect ing the OS D & Auto numbering 3-1 Chapter 3: Passw ord protectin g the OSD & A uto numbering The Managem ent OSD comes with an adv anced password security system that contains 3 different security levels. Each security level has different access righ ts to the system .
Enabli ng passw ord protection 3-2 Enabling passw ord protection By default, password protection is disabled. To enable password protection: 1. From the Manag ement OSD Select Com puter window press F7 . The Password box appears. See Figure 3-1. Figure 3-1 The Enter Password box 2.
Passw ord protect ing the OS D & Auto numbering 3-3 Setting up a passw ord The Administrator sets up passw ords for each User Profile in the Password window. See Figure 3- 3. He can also edit the names to g ive each Profile a m ore identifiable name.
Access ing the OS D using a passw ord 3-4 The 6 User Profiles Figure 3-4 The Setup window To set the User Profiles access levels: 1. Navigate to the desired User Profile and com puter. 2. Change the desired access lev el by pressing the Spacebar. 3. Repeat steps 1 and 2 for each User Profile and com puter.
Passw ord protect ing the OS D & Auto numbering 3-5 T imeout When password protection is activated y ou can automatically disable the Management k eyboard, m ouse and screen after a preset time of non- use. You set the Timeout period in the OUT colum n of the Setup window (F3).
Auto numbering – F1 2 3-6 A uto numbering – F12 Auto num bering giv es each Phantom Rem ote a sequential ID number. Auto num bering is done throug h the Managem ent OSD. For Auto numbering to work properly ALL connected com puters MUST be switched on To perform Auto num bering: 1.
Operating the Ph antom system w ith the Co ntrol software 4-1 Chapter 4: Operatin g the Phantom system w ith the Contro l softw are As an alternative to the O SD you can operate the Ph antom sy stem with the C ontrol software located on the Marketing & Documentation CD.
The V i ew menu 4-2 SD P110 www.m inicom. com USER COMPUTER SYSTEM S ERVICE POWER 85-265VAC 50/60 Hz To System Out po rt To Phant om Remote Syst em In port Shielded CAT5 FTP cable To comp uter’s Ser.
Operating the Ph antom system w ith the Co ntrol software 4-3 Selecting a Com port During the Setup process y ou will be prom pted to choose a Com port. C hoose the Com port to w hich the RS232 Serial cable is connected. Failure to select the correct Com port will result in the software running in demo m ode.
The V i ew menu 4-4 Communication Er ror If a Com munication Error box appears when try ing to scan the system – see Figure 4- 3. Figure 4-3 Communication Error Check that: • The RS232 Serial cable is connected to the com puter’s and Phantom Manager’s serial port s.
Operating the Ph antom system w ith the Co ntrol software 4-5 The toolbar buttons Get Status If for w hatever reason there is a break in com m unication between the Control software and the Phantom system , click to get the current status of the com puters in system .
The tool bar buttons 4-6 Logo and Passw ords You can edit the logo that appears at the top of the OSD window. You can also edit the nam es and passwords for the Administrator, Superv isor and 6 Users. 1. Edit the Logo and Passwords by choosing them from the Edit m enu.
Operating the Ph antom system w ith the Co ntrol software 4-7 Single computer settings To see all the settings of a single com puter righ t click on the com puter icon. The settings appear as in the figure below. Note! There is no Select box to check.
Passw ord protect ion 4-8 User (Statu s U) – Lowest There are 6 different Users in the Phantom sy stem. Each U ser has a Profile that defines the access level to different computers.
Renumbering t he Phantom Remotes 5-1 Chapter 5: Renu mbering the Phan tom Remotes When the Phantom system was first installed, ID numbers were assig ned with the auto- numbering process. Auto num bering giv es each Phantom Rem ote a sequential num ber according to its physical location in the daisy chain.
Scanni ng the sy stem 5-2 Selecting a Com por t 1. From the Op tions menu, select Com por t. The Com port no. box appears. 2. Choose the Com port to which the RS232 Serial cable is connected. 3. Click OK . Legend The color-coded com puter icons are explained in the table below.
Renumbering t he Phantom Remotes 5-3 A uto numbering Auto num bering fills in any blank ID number boxes with the first av ailable free ID number. To perform Auto num bering: 1. In the toolbar, click Auto Number ing . All blank boxes are filled in. 2. Click Apply .
Rem ote wi th d ipswitches 5-4 Remote w ith dipsw itches When adding a Rem ote with dipswitches to the system , check that it does not hav e an ID num ber that is already in use. I f it does, then when performing the scan, a Configuration Error box appears.
Renumbering t he Phantom Remotes 5-5 Fail icons When after a carrying out a numbering procedure, Fail icons appear – see Figure 5- 7. Wait 30 seconds and repeat the numbering procedure.
Upgradin g the Phantom firm ware 6-1 Chapter 6: Upg rading the Phan tom firmw are With the Phantom Update software prog ram y ou can upgrade the firm ware for the: • OSD • Manager • Remote Phantom Update enables y ou to add new features and fix bugs in a quick and efficient manner.
Start ing and Conf iguri ng Phantom Update 6-2 Starting and Confi guring Phantom Update 1. Start the Phantom Update software. The Phantom Update window appears. See Fig ure 6-1. Remote computers M anager box Status box Figure 6-1 The Phantom Update window The table below explains the functions of the buttons and boxes in the Phantom Update window.
Upgradin g the Phantom firm ware 6-3 Display ing the maximum number of Remote units Select the maxim um number of Rem ote units to display in the Phantom Update window. By default 64 Rem ote units are displayed. 1. From the Options m enu choose Remot es .
V erifying the Rem ote version num ber 6-4 M anager box Figure 6-5 The OSD Manager option The H/W Version button is grayed out, as there is no hardware relevant to the OSD. The Phantom Manager version number To verify the Phantom Manager v ersion number: 1.
Upgradin g the Phantom firm ware 6-5 Updating the fir mwa re Warning! Never switch off any computer connected to the Phantom system during the updating process. To update the firmware: 1. Open the Phantom Update program . 2. Activate the Firmw are Upgrade mode on the Manag er OSD.
Wro ng fi rmw a re 6-6 W rong fi rmw are When the firmwar e y ou are try ing to flash is incompatible with the Phantom units a Not Compatible message appears stating that some or all units ar e not compatible with the se lected firmware . Figure 6-7 The Not Compatible message I n this case go to http://www.
Upgradin g the Phantom firm ware 6-7 Electricity failure When the electricity fails while updating the Phantom firm ware, do the following: If the electricity fails during the firm ware update of the Manager, a Communication Error m essage appears.
Phantom Specter USB SUN Combo k eys A-1 A ppendix A : Phanto m Specter USB SUN Combo keys The SUN keyboard consists of a special k eypad to perform special functions in the SUN Operating System environm ent.
デバイスMinicom Advanced Systems Phantomの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Minicom Advanced Systems Phantomをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMinicom Advanced Systems Phantomの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Minicom Advanced Systems Phantomの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Minicom Advanced Systems Phantomで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Minicom Advanced Systems Phantomを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMinicom Advanced Systems Phantomの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Minicom Advanced Systems Phantomに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMinicom Advanced Systems Phantomデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
