AbocomメーカーUTM560の使用説明書/サービス説明書
ページ先へ移動 of 19
USB V.90 TINY MODEM Quick Installation Guide.
FCC REGULATORY STATEMENTS The United States Federal Com munication Com mission (FCC) and the Canadian Department of Com munications have established certain rules governing the use of modem s and other electronic equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pr ovide reasonable protection against harmful interference in a residential installation.
Table of Contents Introduction .............................................................1 S PECIFICATIONS .....................................................1 Modem ............................................................... 1 Fax ..........
Introduction The USB V.90 Tiny Modem com plies with the Universal Serial Bus f unctionality built in Windows 98/2000/Millennium. It is com patible with Bell, ITU-T (formerly CCITT) and Hayes AT com mands. The USB V.90 Tiny Modem enables you enjoy all the benefit offered by USB technol ogy and get a faster and easier Internet access.
- 2 - System Requirements A Pentium processor-based personal computer 166MMX or above At least 16 MB of R AM An USB port Microsoft Windows 98/2000/Millennium A CD-ROM drive.
Hardware Installation 1. Locate the USB host port of your system. Connects the USB Type A connector to the USB host port on your com puter. 2. Connects the phone line to the phone line jack - 3 -.
Software Installation Installation for Windows 98 1. When the USB V.90 Tiny Modem is well connected to your computer, Windows 98 will automatically detect the new device. Click Next. 2. Select Search for a suitable driver for my device (recommended) and click Next.
- 5 - you load the device driver. Click Next. Windows will start searching for the appr opriate driver for the software installation. 4. Click Next. 5. Click Finish. The software installation is successfully completed. 6. When the following dialog box appears, select the country/locati on where you are, and click Enable PBX.
- 6 - Setup Diagnostics You can perform the foll owing steps to check if your USB V.90 Tiny Modem is well installed. 1. Go to Start → Settings → Control Panel → Modems . 2. When the Modems Properties dialog box appears, select the Diagnostics tab.
Installation for Windows 2000 1. Once the USB V.90 Tiny Modem is well connected to your computer, Windows 2000 will automatically detect the new device. Click Next. 2. Select Search for a suitable driver for my device (recommended) and click Next. 3. Insert the device driver compact disc into the CD-ROM drive.
- 8 - 4. Click Browse button and select the drive where you load the device driver (for exam ple: G:WIN2K ). Click OK. Windows will start searching for the appropriate driver for the software installation. 5. Click Next to continue. 6. Click Yes. 7. Click Finish.
- 9 - Setup Diagnostics To verify whether your USB V.90 Tiny Modem exists in your com puter and is enabled, go t o My Computer → Control Panel → System. Click the Device Manager tab. If the USB V.90 TINY MODEM and Network adapters are found, it means that your Network dev ice is well installed.
Installation for Windows Millennium 1. When the USB V.90 Tiny Modem is well connected to your computer, Windows ME will automatically detect the new device. Select Specify the location of the driver (Advanced) and click Next. 2. Load the device driver com pact disc into the CD-ROM of your system and select Specify a location.
- 11 - 3. Expect a minor dela y for Windows to search for the appropriate driver for the device. C lick Next. 4. Click Finish. The installation pr ogram will continue. 5. Select Specify the location of the driver (Advanced) and click Next. 6. When the above figure appears, repeat step 2, namely, select Specify a location.
- 12 - 7. Click Next . 8. When Windows prom pt you “ Modem Country Selection ”, choose the country where you locate. Select the Enable PBX check box and click OK.
Setup Diagnostics 1. To verify if the USB V.90 Tiny Modem is well installed and enabled, y ou can perform the following steps. 2. Go to Start Settings Control Panel Modems. 3. When the Modems Properties dialog box appears, select the Diagnostics tab.
Internet Access 1. Go to My Computer . 2. Select Dial-Up Networking . 3. Double-click Make a New Connection , a dialogue box will appear for you to nam e the new connection and select the device. Nam e the new connection appropriatel y and click Next .
- 15 - 7. Now, you are ready to connect to the Internet..
デバイスAbocom UTM560の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Abocom UTM560をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAbocom UTM560の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Abocom UTM560の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Abocom UTM560で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Abocom UTM560を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAbocom UTM560の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Abocom UTM560に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAbocom UTM560デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。