Moxa Technologiesメーカー351の使用説明書/サービス説明書
ページ先へ移動 of 21
Moxa Industrial Video Encoder VPort 351 Series Quick Inst allation Guide Fifth Edition, June 2008 © 2008 Moxa Inc., all rights reserved. Reproduction without permission is prohibited. Manual A m p l ic o n . co . u k I T a n d I n s t ru m en t a t io n f or i n du s tr y S al e s : + 4 4 (0 ) 1 27 3 57 0 2 20 W eb s i te : w ww .
- 2 - Overview The VPort 351 is a high performance, 1- channel industrial video encoder that provides up to full D1 (720 x 480) @ 30 FPS video performance.
- 3 - y Built-in web server and RS-232 console for remote access & configuration y 1 auto-sensing 10/100BaseT(X) Ethernet por t or 100baseFX (SC connector) y TCP, UDP, and HTTP network transm issi.
- 4 - VPort 351 Panel Layout VPort 351 Front Panel View VPort 351-M-SC Front Panel View 17 7 8 13 12 9 10 16 11 15 18 14 2 1 2 1 T op Panel View Rear Panel View 20 19 19 V1, V2: 12-32 VDC 12-30 VAC RS-232 CONSOLE 1 5 4 6 3 2 1. Grounding screw 2. RS-232 console port 3.
- 5 - First-Time Installation and Configuration Before installing the VPort 351 video enc oder, check to make sure that all items in the Package Checklis t are in the box. In addition, you will need to use a notebook or PC equipped with an Ethernet port.
- 6 - NOTE The PTZ control protocol is not standardized. To use a particular PTZ control protocol, the video server must support the driver for that protocol. Currently, the VPort 351 supports PTZ control protocol drivers for: 1. Pelco D 2. Pelco P 3.
- 7 - NOTE You may download the VPort a nd Ether Device Configurator software from Moxa’s web site at www.moxa.com. 2. The Broadcast Search window will show a list of all switches and VPorts located on the network. The progress of the search will also be indicated.
- 8 - Network Environment without DHCP Server If your VPort 351 is connected to a ne twork that does not have a DHCP server, then you will need to conf igure the IP address manually. The default IP address of the VPort 351 is 192.168.127.100 and the default subnet m a sk is 255.
- 9 - Step 8: Accessing the Homepage of the VPort 351’s web-based manager After installing the ActiveX Control co mponent, the homepage of the VPort 351’s web-based manager will appear. Check the following items to make sure the system was installed properly: 1.
- 10 - NOTE After accessing the VPort 351’ s web-based manager, administrators should access System Configuration Æ System Æ Account to set up the administrator’s password and enable the authentication function. The admini strator account nam e is admin.
- 11 - Mounting Dimensions (unit=mm) Rear View Side View Front View Wall Mounting Kit DlN-Rail Kit DlN-Rail Kit DlN-Rail 105.00 10 10 5 7.75 30.50 7.75 9.00 0 0 . 5 3 40.00 30.00 0 0 . 5 3 1 9 2 . 5 2 13 18 13 0 2 . 7 2 0 3 . 8 4 4 5 . 9 3 1 6 . 6 4 6 5 .
- 12 - Wall Mounting (Optional) Follow the steps below to mount th e VPort 351 on a wall or panel. STEP 1 : Remove the aluminum DIN-Rail attachme nt plate from VPort 351, and then attach the wall mount plates, as shown in the diagrams below. ⇒ T op plate Bottom plate STEP 2 : Mounting the VPort 351 on the wall requires 4 screws.
- 13 - ATTENTION Safety First! Be sure to disconnect the power cord before installing and/or wiring your Moxa switch. This device has UL508 approval. Use copper conductors only, 60/75°C, Tighten To 4.5 pound-inches. For use in Pollution Degree 2 Environment.
- 14 - Wiring the Redundant Power Inputs The VPort 351 has two power inputs, la beled PWR1 and PWR2, on the 6-pin and 8-pin terminal block connectors. Top and fr ont views of the terminal block connectors are shown in the following figures.
- 15 - Wiring the Digital Inputs The VPort 351 has two digital inputs, labele d DI1 and DI2. Each DI consists of two contacts of the 6-pin terminal bloc k connector located on the VPort’ s top panel. Top and front views of one of the terminal block connectors are shown here.
- 16 - RJ45 (10-pin) to DB9(F) Ca ble Wiring RJ45 Plug Pin 1 DCD DSR RTS GND TxD RxD CTS DTR DCD DTR CTS GND RxD TxD RTS DSR 1 2 3 4/7 5 6 8 9 1 6 7 5 3 2 8 4 RJ45 (10-pin) to DB25 (F) C able Wiring R.
- 17 - RJ45 (8-pin) to RJ45 (8-pi n) Straight-Through Cable Wiring Straight-Through Cable RJ45 Plug Pin 1 Switch Port RJ45 Connector RJ45 Connector Tx+ Tx- Rx+ Rx- VPort Ethernet Port Cable Wiring 3 3.
- 18 - LED Indicators Several LED indicators are located on the front panel of the VPort 351. The function of each LED is described in the table below.
- 19 - Hardware Reset A recessed RESET button is provided for restoring the system to the factory default settings. When the system fails to install properly, or operates abnormally, push the RESET button located on the top panel of the VPort 351 to restore the factory defaults.
- 20 - LED Indicators STAT Indicates if the system booted properly PWR1 Power 1 PWR2 Power 2 FAULT Can be configured to correspond to system alarm, power failure, video loss, or disconnected network V.
- 21 - Security y User level password protection y IP address filtering Recommended System Requirements y Pentium 4, 2.4 GHz or above y 512 MB memory or above y Windows XP/2000 with SP4 or above y Internet Explorer 6.
デバイスMoxa Technologies 351の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Moxa Technologies 351をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMoxa Technologies 351の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Moxa Technologies 351の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Moxa Technologies 351で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Moxa Technologies 351を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMoxa Technologies 351の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Moxa Technologies 351に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMoxa Technologies 351デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。