Arrow PlasticメーカーCL72-Aの使用説明書/サービス説明書
ページ先へ移動 of 24
* Size rounded off to the nearest foot BUILDING DIMENSIONS CAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ SAFETY INFORMATION PROVIDED IN THIS MANUAL BEFORE BEGINNING CONSTRUCTION.
2 Owner's Manual Bef ore beginning constr uction, chec k local building codes regarding f ootings, location and other requirements. Study and understand this owner's manual. Impor tant infor mation and helpful tips will make y our construction easier and more enjo y able .
3 Selecting and Pr eparing Y our Site: Before assemb ly , y ou will want to decide on a location f or your b uilding. The best location is a le vel area with good dr ainage. •Allow enough working space for ease of moving parts into position during assembly.
4 Safety precautions are important to follow throughout the construction of your building. •Care must be taken when handling various pieces of your building since some contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your build- ing.
Finish: F or long lasting finish, per iodically clean and wax the e xter ior surface. T ouch- up scratches as soon as you notice them on your unit. Immediately clean the area with a wire brush; wash it and apply touch-up paint per manuf acturer's recommendation.
6 ACCESSORIES.... A6 WEB * Some drilling required to fit buildings without mid-wall bracing. Model No. SS404 • Makes 8" to 12" (20-30cm) wide shelves in any length. • Brackets, braces, hardware included. Lumber is not included. Model No.
THIS P AGE WA S LEFT BLANK INTENTIONALL Y 7.
THIS P AGE WA S LEFT BLANK INTENTIONALL Y 8.
The Foundation For Y our Building 9 FRONT (DOOR) FRONT (DOOR) Foundation BJ09 Note: Finished Slab dimensions, with lumber removed. OPTION 1: W ood Platform If you decide to build your own foundation, be sure to select the appropriate materials.
It is important that the entire floor frame be anchored after the building is erected. Below are recommended ways of anchoring. Anchoring Down The Building Anchoring A10 Arrow Anchoring Kit: (Model No. AK100 or 68383) Recommended for use with the concrete foundation.
11 66150 Screw Driver Holder (1) 66149 Tool Hook (5) 66462 Hasp (1) 66684 Spring Latch (1) 66183 Roof Trim Cap (4) 66463 Swivel Staple (1) 66714 #6-32x7/16" Flat Hd Bolt (16) 66646 Washer (164) (.
Parts List BK12 12 Assembly P a r t P a r t Quantity Check K e y No . Number Description i n C a r to n List 1 8984 Side Floor F rame 2 2 9429 Ramp 1 3 9430 F ront/Rear Floor F rame 2 4 9431 Mid W all.
13 Assembly by Key No. BK13.
S tep 1 BJ14 14 The door header reinforces the front wall and roof. It is made up of two pieces. 1 Positioning the door header as shown, attach a starter strip to head- er using four screws, where shown.
S tep 2 BK15 15 STEP 7 ● P ar ts Needed F or ● Door Assembly ● ● ● ● ● 9435 Horizontal Door Brace (four) ● ● ● ● ● 9936 Right Door (one) ● ● ● ● ● 9937 Left Door (one.
16 S tep 3 BJ16 The floor frame at the front of building is made up of two pieces. Proceed as follows: 1 Center the ramp on top of the front floor frame. Join the frames by in- serting four screws. 2 Place the floor frames on the foun- dation. Assemble the four corners of the floor frame using two screws at each corner as shown.
17 S tep 4 BK17 NOTE The remainder of the building assembly requires many hours. Do not continue beyond this point if you do not have enough time to complete the assembly today. A partially assembled building can be severely damaged by light winds. Each screw and bolt in the wall re- quires a washer.
S tep 5 BJ18 18 The main frame pieces give rigidity to the front and rear walls. 1 Fasten the rear wall angle across the top of the rear wall using four screws.
S tep 6 BK19 19 Each wall panel has a crimped rib on one side. The crimped rib should go under the rib of the panel that follows it. The rear header supports the rear wall and roof. 1 Fasten the wall panels at the top and bottom with screws. 2 Fasten overlapping ribs using two screws and a bolt with nut.
20 S tep 7 BJ20 1 Lift and fasten a right and left gable, under rear header, to the right and left hand wall with four screws. Join gables to header in the rear corners, using a screw. 2 Position roof rafters across width of building, under rear header, with tab on top of door header.
S tep 8 BK21 21 STEP 1 The door jambs reinforce the door opening and provide an attractive trim. Follow these steps for both door jambs. 1 Fasten a door jamb to the front corner panel with one bolt and nut as shown. 2 Fasten the top of the door jamb to the door header with two screws.
S tep 9 BJ22 22 STEP 1 Each screw and bolt in the roof re- quire a washer. NOTE Measure the building diagonally again and make adjustments to make sure the building is square. This will make the roof panel fit better, and holes will align. 1 Position roof panel on top and fas- ten to rear header, roof rafters and gables using screws.
23 S tep 10 BK23 Screw Driver Holder (1) 1 Fasten the mid wall frame across the middle of the rear wall using eight bolts and nuts. 2 Position a shelf inside mid wall frame and slide to the end of building. Fasten using bolts and nuts through panels. Repeat Step 2 for the opposite shelf.
S tep 1 1 BK24 24 ● ● ● ● ● Right Door Assembly (one) ● ● ● ● ● Left Door Assembly (one) ● P ar ts Needed F or ● Door Installation CL72-A BK24 1 Position doors in corners of door opening as shown and fasten hinges with 7/16" flat head bolts and #6-32 hex nuts.
デバイスArrow Plastic CL72-Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Arrow Plastic CL72-Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはArrow Plastic CL72-Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Arrow Plastic CL72-Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Arrow Plastic CL72-Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Arrow Plastic CL72-Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はArrow Plastic CL72-Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Arrow Plastic CL72-Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちArrow Plastic CL72-Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。