Napco Security Technologiesメーカー800Sの使用説明書/サービス説明書
ページ先へ移動 of 16
OPERATING GUIDE FOR YOUR MAGNUM ALEm-800/800s SECURITY SYmM 01955 NAPCO.
You have taken a major step in protecting your home or busi- ness by having a Napco Magnum Alert-800/800S Alarm Control Center installed. Please read this guide thor- oughly to familiarize yourself with your new security system. Keep this booklet handy for future reference.
A delay period that allows the system to be reset before it reports to a cantml station. AlmmPlmn Identifies the areas of tected by each zone o r our premises pro- protection and lists zone features (see page 15). Anrrkrg/- Turning yours tern ON or OFF.
lndlcator ughts -/-n=Y wm 1-1 l Steady - system is armed. l Flashes - system is in alarm. Count the number of flashes to tell in which zone the alarm occurred. Example: Fourflashes- alarm in Zone 4. smU9Mf-l l Steady - system is disarmed, all zones okay.
Each security system is custom tailored to the owner’s needs, but all MAGNUM ALERTBOO/ 800s have the following: 1. zones 2.lhdMg~KayKeypad f.TheAIammOutput Your system contains up to six f=Wkay_J When any zone is activated, separate zones.
uslrBgyourcdetoaml addiurmtheqs8mm If your system includes the Once you enter your personal Napco Digit-Key keypad you can code into the Napco Digit-Key choose your own private code keypad, the red ARMED/MEMORY to arm and disarm the Control light will go on to show the Control Center.
First, check the green STATUS light at the keypad or keyswitch. If this light is on stead- ily, enter your code. The red ARMED/MEMORY light will come on and the green lamp will go out. Leave immediately through the entry/exit doorway before the delay time runs out.
SHUNT button, labeled “S”, and enter your code. The yellow SHUNT light and the red ARMED/ MEMORY light will come on. The green light will be out. All zones programmed by your alarm spe- cialist to respond to manual shunting will be shunted (even if some are not in “trouble”).
Arming with zone shunting You might have chosen one or two zones that you can man- ually “shunt out” of the system from the keypad. A shunted (bypassed) zone cannot cause an alarm. Zone shunting may be used for turning off interior protection, or allowing you to turn on only your perimeter protection.
Panic alarm To activate a panic alarm and call for outside help, press the two buttons marked l and # on the Digit-Key keypad. Makesure you press both buttons at the s8me time. The panic zone is capable of sending asilent signal to the Central Station when a Digital Communicator is being used (optional).
Your Alarm Specialist may have programmed your security system to be monitored by a Central Station. The built-in digital communicator can trans- mit emergency signals to the Centml Station 24 hours a day.
AbortDeby Note which zones on your Cantfal Madon alarm plan have abort delay. This mribwk is a 16 second delay that enables The Central Station will ac- An optional feature that per- you to reset the .
The following information is applicable only where local ordinance permits use of your alarm Control Center for fire detection Controrlklg Your Fin Circuit If your alarm specialist installed smoke detectors or heat sensing thermostats, you have 24 hour fire protection.
an escape plan Even with the most advanced fire alarm system, adequate pro- tection requires an escape plan. To prepare your plan: Draw floorplans of your build- ing (see sample). Show two exits: a front or back door and a window from each room. (Make sure the window works.
Zone Area Protected Zone Features Contacts (doors, windows, etc.) 1 3 I 4 I Aux. (6) Central Station? Service Person ‘optlonal katun, Telephone# , Telephone# 15.
NAPCOLlMiTEDWARRANly.
デバイスNapco Security Technologies 800Sの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Napco Security Technologies 800Sをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNapco Security Technologies 800Sの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Napco Security Technologies 800Sの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Napco Security Technologies 800Sで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Napco Security Technologies 800Sを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNapco Security Technologies 800Sの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Napco Security Technologies 800Sに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNapco Security Technologies 800Sデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
