Napco Security TechnologiesメーカーXP-400の使用説明書/サービス説明書
ページ先へ移動 of 16
Using Your XP-400 Securit y System ARMED READY SYSTEM ü ZONE 1 ZONE 2 ZONE 3 ZONE 4 NAPCO Oi220a.pub page 1 Thursday, December 18, 1997 18:31.
2 Oi220a.pub page 2 Thursday, December 18, 1997 18:31.
Introduction Congratulations on your purchase of an advanced NAPCO EXPRESS XP-400 Security System. Meticulously developed by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind & incorporates some of the most sophisticated features available today.
4 1 Bell / Battery Test Test your bell or siren by pressing A followed by 1 . This will cause the bell, or siren to sound for 2 seconds and also initiate a test of the battery . 2 Central Station Communication Test (This test should only be performed on weekends or at a time designated by your alarm company) 1.
ARMED READY SYSTEM ü ZONE 1 ZONE 2 ZONE 3 ZONE 4 Keypad Controls and Indicators Ready Light will light when all zones are secure and system is ready to be Armed. Zone Lights ( 1 through 4) will light to indicate that the corresponding Zone is open, and will flash to indicate a zone in alarm.
Arming Your System When Leaving 1 Before arming your system, make sure the Green Ready light is ON. This indicates that all of your prot- ective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure these zones before proceeding.
Protecting Yourself While at Home 1 Before arming your system, make sure the Green Ready light is ON. This indicates that all of your protective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure those zones before proceeding.
Emergency Buttons The two sets of emergency buttons, if programmed, are always active whether the system is armed or disarmed. Discuss these buttons with your installer. The emergency signal will only be activated when the two respective buttons are pressed at the same time.
Disarming Your System when Returning 1 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system before your Entry Delay time expires. 2 Enter your user code. The Red Armed light will go out, indicating that the system has been disarmed.
Special Functions A By pressing A followed by the appropriate key, (do not press simultaneously) these special functions and features can be enabled: A0 Easy Arm (when system is disarmed) The Easy Arm feature allows the system to be armed by pressing a followed by 0 .
Your Installer has assigned a User 1 Code which may be used to not only Arm and Disarm the system, but also to enter the User Program Mode, where you can program and/or reprogram up to 4 User Codes. The following explains how you will use this code to program or erase additional user codes.
The XP400 is constantly monitoring its own components, as well as all critical services, such as AC Power and the Telephone line, to insure that it is always ready to provide the protection for which it was designed. When a system trouble does occur, it will caution you by lighting the Yellow ü ü SYSTEM light and beeping the keypad buzzer.
13 ü ü System Troubles Keypad Beeps or ü ü SYSTEM Flashes Zone light ON System Trouble Condition Action 2 Beeps 1 Bell / Siren Trouble There is a problem with the Bell or Siren. Call installing com- pany for service. 2 Beeps 3 Wireless Receiver Trouble A problem has been detected with the wireless receiver.
Ambush Code - In the event that you are forced by an intruder to dis- arm your system, this special code can be used to disarm the system, and simultaneously send a silent alarm to Central Station.
15 Notes Oi220a.pub page 15 Thursday, December 18, 1997 18:31.
NAPCO LIMITED WARRANTY THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC . This equipment generates and uses radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception.
デバイスNapco Security Technologies XP-400の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Napco Security Technologies XP-400をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNapco Security Technologies XP-400の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Napco Security Technologies XP-400の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Napco Security Technologies XP-400で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Napco Security Technologies XP-400を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNapco Security Technologies XP-400の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Napco Security Technologies XP-400に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNapco Security Technologies XP-400デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
