NECメーカーEU1V0UM00の使用説明書/サービス説明書
ページ先へ移動 of 19
Quick Startup Guide Low-Voltage Starter Kit For Motor Control Document No. UxxxxxEU1V0UM 00 © 2006 April. NEC Electronics Am erica, Inc. All rights reserved.
Motor Control I/O Board User’s Manual ii The information i n this document is current as of April 2006. The inform ation is subject t o change without notice. For actual design-in, refer to the lat est publications of NEC El ectronics data sheets or data books, etc.
Motor Control I/O Board User’s Manual iii.
Motor Control I/O Board User’s Manual iv Revision History Date Revision Section Description 04-2006 — — First release.
Motor Control I/O Board User’s Manual Contents 1. Introduction ..................................................................................................................................... 1 2. Kit Contents ..................................
.
Motor Control I/O Board User’s Manual 1. Introduction The low-voltage starter kit for motor control (M C-LVKIT-714) is a complete 3-phase motor control evaluation system for NEC Electronics’ microcontro ller-type, application-specific standard products (ASSPs) for motor control.
Motor Control I/O Board User’s Manual For the instruction descriptions, refer to the 78K/0 Series Instruction User’s Manual (U12326E) 3. Hardware Setup The kit can be purchased as one unit with a ll three boards connected as shown below: Figure 2.
Motor Control I/O Board User’s Manual Figure 3. Motor Phase Connections Figure 4. Hall Sensor Connections The software to run the motor is programm ed in to the microcontroller’s flash mem ory.
Motor Control I/O Board User’s Manual To control the motor from a GUI on your PC, conn ect a serial cable to the J9 RS-232 port on the MC-IO board and rebuild the code with the GUI macro option as described later in this manual. Figure 5. Standalone Oper ation Three seconds after power up, the LED displays the current set speed.
Motor Control I/O Board User’s Manual condition is displayed on the seven-segment LED. For details on the protection functions implemented in hardware, consult the user’s m anual for MC-PWR-LV low-voltage power module. The sample code software also has built-in fau lt detection algorithms as an extra m easure of protection.
Motor Control I/O Board User’s Manual Figure 7. Motor Con t ro l So ftware an d Documents Installation GUI 4. Install all of the software in the following recommended sequence: • NEC Electronics C compiler and assembler software • MC-LVKIT-714 software Figure 8.
Motor Control I/O Board User’s Manual 2. Remove jumpers JP5 2-5, JP5 3-6 and 2J P7 1-2 and reconnect M-78F0714 to MC-IO board. 7.
Motor Control I/O Board User’s Manual Figure 9. Jumpers fo r Stan d alone Operation Figure 10. Debugging Setup 3. Attach the on-chip debugging emulator’s targ et connector to 2JP7 on the M-78F0714 and the USB cable to your computer as shown bellow.
Motor Control I/O Board User’s Manual Figure 11. Debugging Environment Show n with QB-78K0MINI On-Chip Debugger Note : The on-chip debugger has a 5 MHz internal clock source by default. The MC-78F0714 must be operated at 20 MHz. Use th e external 20 MHz oscillator supplied with the kit.
Motor Control I/O Board User’s Manual Figure 12. PM Plus Workspace 4. Click File and select Open Workspace . 5. Browse to C:NECTools32 Motor_ControlBLDC_Hall_714 and select BLDC_LV.prw PM Plus workspace file. 6. The newly loaded workspace file will cont ain one project called LV_BLDC_Hall-714.
Motor Control I/O Board User’s Manual through the on-chip debugging emulator and the source code displayed in the Debugger window as shown below. Figure 14. Source Code in Debugging Window 2. Use the RUN command to execute code in debugging m ode. At this point, the motor can be controlled from the user interface in standalone mode or GUI m ode.
Motor Control I/O Board User’s Manual 10. GUI Operation To operate the motor from the PC GUI, the code has to be rebuilt with “GUI” option. Select Compiler Options from PM+ Tool me nu and type “GUI” in Preprocessor Define Macro entry. Figure 15.
Motor Control I/O Board User’s Manual The GUI will launch if the connection is established: Figure 17. BLDCM GUI 2. To operate the motor, use the controls in the GUI. 3. To change the PID parameters click on the tuning key symbol Figure 18. Launching PID Parameter Window The tuning window will allow the changing of P, I or D constants: Figure 19.
デバイスNEC EU1V0UM00の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
NEC EU1V0UM00をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNEC EU1V0UM00の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。NEC EU1V0UM00の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。NEC EU1V0UM00で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
NEC EU1V0UM00を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNEC EU1V0UM00の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、NEC EU1V0UM00に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNEC EU1V0UM00デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。