NECメーカーMultiSync E232WMTの使用説明書/サービス説明書
ページ先へ移動 of 19
MultiSync E232WMT User’s Manual.
Index W arning, Caution ........................................................................................................................................... English-1 Registration Information ....................................................
English English-1 TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPT ACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULL Y INSER TED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOL T AGE COMPONENTS INSIDE.
English-2 Registration Information FCC Information 1. Use the attached specied cables with the MultiSync E232WMT (L233QV) monitor so as not to interfere with radio and television reception. (1) The power supply cord you use must have been approved by and comply with the safety standards of U.
English English-3 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONIT OR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks.
English-4 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK F A TIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for the display to warm up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level.
English English-5 Contents Y our new NEC monitor box* should contain the following: • MultiSync monitor with tilt/height adjust stand • Power Cord* 1 • Video Signal Cable (DVI-D to DVI-D cable)* 2 • Video Signal Cable (Mini D-SUB 15 pin to Mini D-SUB 15 pin) • USB Cable* 3 • Audio Cable (ø 3.
English-6 Quick Start T o connect the LCD monitor to your system, follow these instructions: NOTE: Make sure to read “Recommended use” (page 3) before installation. 1. Turn of f the power of your computer . 2. For a PC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your system ( Figure A.
English English-7 3. Place hands on each side of the monitor to tilt the LCD panel and lift up to the highest position. NOTE: Handle with care when tilting the monitor screen.
English-8 UP DOWN AUTO MENU POWER Figure E.1 LED Indicates that the power is on or off. LED The white light is lit up while the camera is in operation. Microphone Microphone Camera Raise and Lower Monitor Screen T o raise or lower screen, place a hand on each side of the monitor and lift or lower to the desired height ( Figure RL.
English English-9 Remove Monitor Stand for Mounting T o prepare the monitor for alternate mounting purposes: 1. Disconnect all cables. 2. Place a hand on each side of the monitor and lift up to the highest position. 3. Place monitor face down on a non-abrasive surface ( Figure S.
English-10 Controls OSD (On-Screen Display) control keys on the side of the monitor function are as follows: T o access OSD menu, press the MENU key . T o change signal input, press the AUTO/EXIT key .
English English-1 1 BRIGHTNESS / CONTRAST Contrast (Only when Eco Mode Off) Adjusts the overall image and background screen brightness by input signal level. Brightness (Only when Eco Mode Off) Adjusts the overall image and background screen brightness.
English-12 OSD Setup Timeout Y ou can select how long the monitor waits after the last touch of a key to shut of f the OSD menu. Language Selects the language used by the OSD. Extra Input Select Changes the video input source. Reset Allows you to reset all OSD control settings back to the factory settings.
English English-13 Specications Monitor Specications MultiSync E232WMT Notes LCD Module Diagonal: Viewable Image Size: Native Resolution (Pixel Count): 58.42 cm/23.0 inches 58.42 cm/23.0 inches 1920 x 1080 Active matrix; thin lm transistor (TFT) liquid crystal display (LCD); 0.
English-14 T roubleshooting No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • The monitor does not support DisplayPort converter signal. • Power Switch and computer power switch should be in the ON position.
English English-15 USB Hub does not operate • Check to make sure the USB cable is properly connected. Refer to your USB devise User’s Manual. • Check if the USB upstream port on the monitor is connected to the USB downstream port on the computer .
English-16 TCO Certied Displays 6 Congratulations! This product is TCO Certied – for Sustainable IT TCO Certied is an international third party sustainability certication for IT products. TCO Certied ensures that the manufacture, use and recycling of IT products reect environmental, social and economic responsibility .
English English-17 Manufacturer’s Recycling and Energy Information NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment.
デバイスNEC MultiSync E232WMTの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
NEC MultiSync E232WMTをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNEC MultiSync E232WMTの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。NEC MultiSync E232WMTの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。NEC MultiSync E232WMTで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
NEC MultiSync E232WMTを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNEC MultiSync E232WMTの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、NEC MultiSync E232WMTに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNEC MultiSync E232WMTデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。