NECメーカーNP4001-10ZLの使用説明書/サービス説明書
ページ先へ移動 of 151
Projector NP4001/NP4000 User’s Manual.
© NEC Display Solutions, Ltd. 2007 Second edition July 2007 • DLP, BrilliantColor and DynamicBlack are trademarks of Texas Instruments. • IBM is a trademark or registered trade mark of International Business Machin es Corpora- tion. • Macintosh, Mac OS X and PowerBoo k are tradem arks of Apple, Inc.
i Important Information Safety Cautions Precautions Please read this manual carefully before usin g your NEC NP4001 /NP4000 projecto r and keep the manual handy for future reference. Your serial number i s located on the bottom of your projector. Record it here: CAUTION: To turn off main power, be sure to remove the plug from power outlet.
Important Information ii Laser Rating This label is on the side of the remote control. This mark is on the top of the remote control. CAUTION Use of controls or adju stments or performance of procedures other than those specified herein may result in haza rdous radiation exposure.
Important Information iii RF Interference (for USA only) WARNING: The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specifi ed by NEC Display Solutions of Amer- ica, Inc. in this manual. Failure to comp ly with this government regulation could void your right to operate this equi pment.
Important Information iv • If you wish to have the proj ector installed on the ceiling: Do not attempt to install the projector yourself. The projector must be installed by quali f ied technicians in or der to ensure proper operation and reduce the ri sk of bodily injury.
Important Information v Fire and Shock Precautions • Ensure that there is sufficient ventilati on and that vents are unobstructed to prevent the build-up of heat inside your projector. A llow at le ast 8 inches (2 0cm) of space be - tween your projector and a wall.
Important Information vi • Turn off the projector, unplug the powe r cable an d have the projector serviced by qualified service personnel under the following co nditions: When the power cable or plug is damaged or frayed . If liquid has been spill ed into the projector, or if it has been expose d to rain or water.
Important Information vii Remote Control Precautions • Handle the remote control carefully. • If the remote control gets wet, wipe it dry immediately. • Avoid excessive heat and humidity. • Do not heat, take apart, or throw batteries into fire.
viii Table of Contents IMPORTANT INFORMATI ON ............................................................................................................. I S AFETY C AUTIONS ...........................................................................
Table of Contents ix Lens Shift Adjustable Rang e ..................................................................................................... 42 From the Remote Control Unit ...................................................................
Table of Contents x Version .......................................................................................................................................... 99 v R ESET M ENU D ESCRIPTIONS AND F UNCTIONS .....................................
1 1. Introduction n What’s in the Box? Carefully unpack the projector and che ck that the following items are in cluded: NP4001/NP40 00 Projector Remote C ontrol (79TD5521) (with Two AA al kaline batt eries) Power cable 3.
1. Introduction 2 o Introduction to the Projector Features you’ll enjoy: z DLP projector wit h high resoluti on z Native WXGA supp ort (NP4001 on ly) A WXGA (1280 x 768) resolu tion provides w ide screen disp lay with an aspect ratio of 15:9.
1. Introduction 3 p Part Names of the Projector Front-right view I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. IR receiver Receiver for IR signal from remote control 12 2. Lamp cover Remove cover to replace lamp or color wheel 107 3. Lens control panel See Lens Controls 7 4.
1. Introduction 4 Top View I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. Lens control panel See 3 Lens Controls 7 2. Right-hand speaker Right-hand speaker — 3. Lamp cover Remove cover to replace lamp or color wheel 107 4. Exhaust vent Exhaust vent – do not obstruct — 5.
1. Introduction 5 Carrying the Projector Always carry your projector by the handle. Before moving or carrying the projector, disconne ct the power cable and any other ca- bles that may be attached to it. When moving the projector or wh en the projecto r is not in use, cover the lens with the lens cap.
1. Introduction 6 Bottom view I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. Height adjusters Adjust projection height 44 2. Intake vent Color wheel cooling vent – do not obstruct — 3. Front filter Keep the fan free of dust – clean regularly for optimum performance 103 4.
1. Introduction 7 q Top Features Lens Controls I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. ZOOM Increase/decrease projected image size 50 2. UP CURSOR 3.
1. Introduction 8 OSD Controls and Status LEDS I TEM L ABEL D ESC RIPTION S EE P AGE : 1. MENU Open / Close the OSD 61 2. SELECT PAD Navigate and change settings in the OSD 61 3. RIGHT CURSOR/ VOLUME INCREASE Increase volume 46 4. EXIT Exit the On-Screen Display (OSD) 62 5.
1. Introduction 9 I TEM L ABEL D ESCRIPTIO N S EE PAGE : Green 8. LAMP 2 Flashing See Indicator Messages 113 Green Orange 9. POWER (LED) Flashing See Indicator Messages 112 10. STATUS (LED) Green Lamp ready you can safely turn on or off the projector 112 11.
1. Introduction 10 r Terminal Panel Features I TEM L ABEL D ESCRIPTION S EE PAG E : 1. COMPUTER 3 IN Connect the DVI cable (not supplied) from a computer 31 2. AUDIO IN (3) Connect the audio cable (not supplied) from the input device — 3. AUDIO OUT Audio loop-thru — 4.
1. Introduction 11 I TEM L ABEL D ESCRIPTION S EE PAG E : 10. SC TRIGGER When connected to the screen through a commercially available cable, the scree n de- ploys automatically on start up of the projector. The screen retracts when the pro- jector is powered off (see notes below) 130 11.
1. Introduction 12 s Part Names of the Remote Control The Remote Control unit supplied with t he projector combines erg onomic design and utility and includes feature s such as Volume and Z oom Co ntrol, Freeze Frame and a useful poi nt- ing tool in the form of a laser.
1. Introduction 13 Important: 1. Avoid using the projector with bright fl uorescent lighting turned on. Certain high- frequency fluorescent lights can disr upt remote control operation. 2. Be sure nothing obstructs the path betw een the remote control and the projec- tor.
1. Introduction 14 Battery Installation The Remote Control unit inclu ded with the projector does not co ntain batteries, though batteries are supplied as part of the co mplete package. To insert (or replace) the batte r- ies, refer to the following guide.
1. Introduction 15 Operating Range for Wi reless Remote Control The infrared signal operates by lin e-of-sight up to a distance of a bout 22 feet (7m) and within a 60-degree angle of the remote sensor o n the projector cabi net.
1. Introduction 16 Using the Remote Control in Wired Operation Connect the supplied rem ote cable to the REMOTE2 jack on the proje ctor (see r Ter- minal Panel Features on page 10 ) and the other end to the remote jack on the remote control (see item 1, s Part Names of the Remote Cont rol on page 12 ).
17 2. Installation and Connections n Setting Up the Screen and the Projector This section briefly descri bes how to set up your projector and h ow to connect video and audio sources. Your projector is simple to set up and use. But before you get started, you must first: • Set up a screen and the projector.
2. Installation and Connections 18 o Selecting a Location Locating the projector co rrec tly ensures optimum performa nce and a longer parts life. Take note of the following when setting up the proje ctor: • The projector table or stand should be level and sturdy.
2. Installation and Connections 19 p Installing or Removing the Optional Lens CAUTION: • Do not shake or place excessive pressure on the projecto r or the lens compo- nents as the projector and lens com ponents contain precision parts.
2. Installation and Connections 20 2. Push the LENS RELEASE button all the way in and rotate the lens counterclockwise. The existing lens will be disengaged. Note: If the lens cannot be removed even by using the LENS RELEASE button, the anti-theft screw for lens may be in use to secure the lens.
2. Installation and Connections 21 Installing the New Lens 1. Insert the lens with the arrow mark on top. 2. Rotate the lens clock- wise until you feel it click into place. Installing the New Lens Using the anti-theft screw Using the anti-theft screw to prevent theft of the lens.
2. Installation and Connections 22 q Throw Distance and Screen Size Example of NP08ZL: The further your projector is from the screen or wall, the larger the image. The mi nimum size the image can be is approximately 40 inche s (1 m) measured diagonally when the projector i s roughly 65 inches (1.
2. Installation and Connections 23 NP4000 Throw Distance and Screen Size Values Screen Size NP06FL NP07ZL NP08ZL Diagonal Width Height (B) Distance (A) [inches] [m] [inches] [m] [inches] [m] [inches] [m] [inches] [m] [inches] [m] 40 1.02 32 0.81 24 0.
2. Installation and Connections 24 NP4001 Throw Distance and Screen Size Values Screen Size NP06FL NP07ZL NP08ZL Diagonal Width Height (B) Distance (A) [inches] [m] [inches] [m] [inches] [m] [inches] [m] [inches] [m] [inches] [m] 40 1.02 34.3 0.87 20.
2. Installation and Connections 25 For screen sizes between 40 inches and 500 inch es not indicated in the tables on pages 23 and 24 , use the formulas below for the throw di stance: T HROW D ISTANCE F OR NP4000 L ENS [ INCHES ] [ METERS ] NP06FL B × 0.
2. Installation and Connections 26 CAUTION Ceiling installation must be done by a qu alified profession al. Contact your NEC dealer for more information. It is not recommended you install the projector your self. Only use the projector on a solid, level surfa c e.
2. Installation and Connections 27 r Replacing Color Wheel The NP4001/NP4000 proj ector comes with a f our-segment color wheel installed. An addi- tional six-segment color wheel come s included. To re place the color wh eel (located under the lamp cover adjacent to lamp 1) re fer to the following guide.
2. Installation and Connections 28 3. Remove the screws from the color wheel cover. Lift cover in the direction shown and place on a clean, dust free surface. 4. Unscrew the retaining screws on the four-segment color wheel. Note: Improper (loose) installation of the color wheel prevents an image from being displayed.
2. Installation and Connections 29 6. Insert the six-segment color wheel 7. Secure the retaining screws as shown. 8. Replace the wheel cover as shown and secure the screws to lock the cover in place.
2. Installation and Connections 30 9. Align the lamp cover (A) with the arrow mark on the cabinet and slide it into place. 10 . Secure the captive screw (B). Storing Unused Color Whe el: Keep the unused color wheel in the zip per bag in which the supplied 6-segment color wheel was packaged.
2. Installation and Connections 31 s Making Connections Connecting Your PC or Macintosh Computer Enabling the computer’ s external display Displaying an image on the note book PC’s sc reen does not necessarily mean it outputs a signal to the projector.
2. Installation and Connections 32 2. Turn on the projector and select the chosen method o f connection from the source menu before turning on the PC (see o Selecting a Source on page 39 ). 3. Turn on the PC. Note: Failure to follow the above steps may not ac tivate the digital output of the graphics card resulting in no picture being display ed.
2. Installation and Connections 33 Connecting an External Monitor Connect an external monit or to the projector through RGB out connections as shown be- low (see item 4, r Terminal Panel Features on page 10 ). Note: • Daisy chain connecti on is not possible.
2. Installation and Connections 34 Connecting Your DVD Player with Component Output To connect a DVD Player to the projecto r, refer to the following guide. 1. Connect the DVD Player to the projector as shown below before turning on the Player or the projector.
2. Installation and Connections 35 Connecting Your VCR or Laser Disc Player To connect you VCR or Laser Di sc Player, refer to the following diagram. Note: Refer to your VCR or laser disc player ow ner’s manual for more information about your device’s requirements.
2. Installation and Connections 36 t Connecting the Supplie d Power Cable Refer to the following guideline s to connect the power supply to the projector. 1. Locate the projector correctly. See o Selecting a Location on page 18 . 2. Ensure Main Power switch is in the off position (O).
37 3. Projecting an Image (Basic Operation) n Turning on the Projector Once the projector is correctly located and the powe r cable and other connectio ns are in place, it is important that the projector is powered on corre c tly in order to avoid damage to components and un necessary wear an d tear.
3. Projecting an Image (Basic Operation) 38 Note on Startup Screen (Me nu Language Select screen) In the first instance of powering on the proj ector, the language menu is displayed to se- lect the default language. Select the required default language u s ing the ▲ or ▼ buttons on the OSD menu panel or the remote control unit and press Enter .
3. Projecting an Image (Basic Operation) 39 o Selecting a Source The Source can be selected from the projector's control pa nel or from the remote control unit. Refer to the following gui de to select Source. 1. Press Menu on the OSD control panel or on the remote control unit to dis- play the Main Menu .
3. Projecting an Image (Basic Operation) 40 p Adjusting the Picture Position and Picture Size The Picture Position and Picture Size can be adju s ted manually from the lens control panel or from the remote control unit. Refer to the follo wing guides to adjust Picture Po sition manually.
3. Projecting an Image (Basic Operation) 41 4. The Aspect Ratio win- dow is displayed. Select the desired picture size using ▲ or ▼ and press Enter . Note: The NP4000 and NP4001 support different Aspect Ratio options as shown. 5. When finished, press Exit to return to the projected image.
3. Projecting an Image (Basic Operation) 42 Lens Shift Adjustable Range The adjustable range for le ns shift is tabulat ed below and subject to the conditio ns listed. Note: The drawings below are applied to the lenses for NP07ZL, NP08ZL, NP09ZL, and NP10ZL.
3. Projecting an Image (Basic Operation) 43 2. Press the directional keys as required to shift the image. Releasing the di- rectional arrow will re- center the cursor. 3. To alter the picture size, press the Aspect button to display the Aspect Ratio window.
3. Projecting an Image (Basic Operation) 44 Adjusting the Projector Level 1. To raise the level of the projec- tor, twist the adjusters clockwise. 2. To lower the level of the projec- tor, lift the projector and twist the adjusters counter clockwise.
3. Projecting an Image (Basic Operation) 45 q Optimizing an RGB Image Automatically Adjusting the Image Using Auto Adjust To optimize an RGB image automatically refer to the following gui de. Press the Auto ADJ. button on the Remote Unit (see item 27, s Part Names of the Re- mote Control on page 12 ) to optimize an RGB image automatically.
3. Projecting an Image (Basic Operation) 46 r Adjusting Volume Up and Down The volume can be adjusted from the OS D Control Panel or with the Remote Control u nit. Refer to the following as a guide. 1. Press the Volume +/- buttons on the remote control or the Select pad left and right keys on the OSD control panel.
3. Projecting an Image (Basic Operation) 47 s Turning off the Projector Once the projector is no longer req u ired, it is important to shut it down correctly to avoid damage or unnecessary wear a nd tear to the projector. CAUTION • Do not unplug the power cable from the wall outlet o r projector when the projector is powe red on.
3. Projecting an Image (Basic Operation) 48 About Direct Power Off The projector has a feature called "Dire ct Power Off". This feature allows the projector to be turned off (even when projecting a n image) using a power strip equipped with a switch and a breaker.
49 4. Convenient Features n Turning Off the Image and Sound The projected image and sound can be turn ed off for short periods of time with the remote control. This feature is usef ul for breaking up presentations or for other brief interruptions in projections.
4. Convenient Features 50 p Adjusting the Focus/Zoom Manually The focus and zoom can b e adjusted manually from the projector focus/zoom p anel or from the remote control unit. Refer to the following g uides to adjust the focus and zoom manually. Adjusting by Using the OSD Control Panel 1.
4. Convenient Features 51 q Changing Lamp Mode The projector has two lamp modes avai lable, Normal and Eco . The Normal mode is used for everyday standard projection, whereas t he Eco mode is used for saving powe r and lamp life. To change the Lamp Mode, refer to the followi ng guides.
4. Convenient Features 52 Changing Lamp Mode by Using the Remote Control 1. Press the Lamp Mode button on the remote control to access the Lamp Mode menu. 2. From the Lamp Mode window, select Normal or Eco using ▲ or ▼ . Move the cursor to OK and press Enter .
4. Convenient Features 53 r Getting Information Press the HELP button on the remote co ntrol to display the "Information" screen. Use ◄ or ► to select a tab.
4. Convenient Features 54 s Adjusting Position/Clock The Position/Clock/Phase and Keystone Corre c tion can be adjusted manually from the pro - jector's control panel or fro m the remote control unit. Refer to the following gui des to adjust the Keystone Distortion manually.
4. Convenient Features 55 Correcting Keystone by Using the Remote Control IMPORTANT: When adjusting the keystone, set the le ns shift position to the following. • Horizontal: the lens center • Vertical: the bottom of the projected image is aligned with the lens center line in height.
4. Convenient Features 56 A DJUSTMENT H ORIZONTAL V ERTICAL Keystone Max. +/– 35° appr ox. Max. +/– 40° approx. The following are conditions under which the maximum angle is achieved: When the NP08ZL lens is used When the lens shift position is se t to the following.
4. Convenient Features 57 t Preventing the Unauthorized Use of the Projector The projector has an inbuilt security featur e to lock the OSD contro l panels and deny remote control operation. The secu rity feature has no default keyword; in the first instance of ena- bling the security feature, t he user must define a keyword.
4. Convenient Features 58 3. You are prompted to enable the Security Function. Select OK and press Enter . Select On using the ▼ button. 4. The keyword window is dis- played. Enter a keyword between 4 and 10 characters using ▲▼◄► . Press Enter .
4. Convenient Features 59 Unlocking the Projector To unlock the projector, refer to the following g uide. 1. When the projector is locked, either by request during opera- tion or at start up, the locked message is displayed. 2. To unlock the projector, press Menu on the control panel or remote control.
4. Convenient Features 60 u Using the Physical Lock For security and authorized usag e, the projecto r comes with two types of security features, the Kensington Lock and t he Security Ch ain Lock.
61 5. Using On-Screen Display n Using the Menus The projector has an On-Screen Display (OSD) that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control or the buttons on the top of the projector to navigate and make changes to the OSD.
5. Using On-Screen Display 62 2. Press the cursor ◄ or ► button to move through secondary menus. 3. Press ▲ or ▼ to select menu items and ◄ or ► to change val- ues for settings. Press Enter to confirm the new setting. 4. Press Exit to close the OSD or leave a submenu.
5. Using On-Screen Display 63 o Menu Tree The gray shaded area indicates factory default settings. M ENU I TEM Source Computer 1, Computer 2, Computer 3, Com ponent, Video, S-Video Adjust Picture Pres.
5. Using On-Screen Display 64 M ENU I TEM Installation Orientation Desktop Front/Ceiling Rear/Desktop Rear/Ceiling Front Communication Speed 4800bps/9600bps/19200bps/38400bps Menu Color Select Color/M.
5. Using On-Screen Display 65 p Menu Elements Some menus and windows contain large amounts of information in a small area. Refe r to the following guide to navigate through options more ea sily. Menu windows or dialog windows typically contain the following elements: I TEM L ABEL D ESCRIPTIO N 1.
5. Using On-Screen Display 66 q Source Menu Descriptions and Functions The Source menu displays all suppo rted image sources. Select the required source from the menu using ▲ or ▼ and press Enter to confirm.
5. Using On-Screen Display 67 r Adjust Menu Descriptions and Functions The Adjust menu contains overall projector setting s for image output such as sharpness, overscan and color matrix. Three tabs are accessi ble through the Adju st menu, Picture, Image Options and Video.
5. Using On-Screen Display 68 Image Options Menu The Image Options menu is used to conf igure image options such as screen positioning and aspect ratio. Access the image o p tions menu in the Adjust menu. The following table lists all functions with a description and the default setting.
5. Using On-Screen Display 69 Aspect Ratio Aspect Ratio alters the appea rance or Ratio of the projected ima ge. The NP4000 and NP4001 support different Aspect Ratio o ptions as shown. NP4000 Aspect Ratio Options: 4:3 – Standard TV screen (4:3), proportionally four u nits wide for every three units high, no matter the size of the screen.
5. Using On-Screen Display 70 NP4001 Aspect Ratio Options: 4:3 – Standard TV screen (4:3), proportionally four u nits wide for every three units high, no matter the size of the screen. 16:9 – A wide-screen aspect ratio for video. 15:9 – Uses the full display.
5. Using On-Screen Display 71.
5. Using On-Screen Display 72 Overscan Video images normally ex ceed the size of the displa y screen. The edge of the picture may or may not de displayed correctly. The border area that is cropped can be adjusted by using the Overscan menu. Set the overscan percentage between 0 – 15% to compensate for different screen sizes.
5. Using On-Screen Display 73 Video Menu The Video menu is used to configure image optio ns such as deinterlace and telecin e. Access the Video menu in the Adjust menu. The following table lists all functions with a description and the default setting.
5. Using On-Screen Display 74 Noise Reduction Select the level of noise reduction re quired. Range: Off, Low, Medium, High. 3D Y/C Separation 3D Y/C Separation sepa rates composite signal to Y (brightne ss) signal and C (color) signal, and can help to produce clearer and sharp er images without overlapping colors (rainbow effect).
5. Using On-Screen Display 75 Color Matrix Color Matrices define the amount of the three-colo r components R (red), G (green), and B (blue) in a single point in color sp ace. Select from the following: Auto – Auto selects the color matrix. RGB – Sets the color matri x to RGB, use for PC monitor or camera imaging.
5. Using On-Screen Display 76 s Detail Settings Menu Descriptions and Functions The Detail Settings menu contains basic and advance d color adjustment option s such as gamma correction, color contrast and color correction. General The General tab contains general Detai l Settings such as gamma correction and color temperature.
5. Using On-Screen Display 77 Reference The Reference mode allo ws the projector to differentiate between source materials for example movies, PC images or video st ills. Select from the following: High-Bright – Select for use in a brightly lit room.
5. Using On-Screen Display 78 White Balance White Balance allows the projector to compe nsa te for different colors of light being emit- ted by different light sources. The following table lists all functions with a brief description. I TEM D ESCRIPTIO N Brightness R Set the Brightness R value to compensate for red light sources.
5. Using On-Screen Display 79 Color Correction The Color Correction tab enable s the adjustme nt of color values in an image to remove unwanted effects, improve color, cha r acteristics o r add more of a particular color. The following table lists all functions with a brief description.
5. Using On-Screen Display 80 t Setup Menu Descriptions and Functions The Setup menus contain the most often used settings durin g installation and options to customize the general o utput of the projector. Three tabs are accessible through the Setup menu, general, installation and option.
5. Using On-Screen Display 81 Keystone The keystone trapezoid ca n be adjusted by selecting this option. Select Horizontal or Vertical usin g ▲ or ▼ then, use ◄ or ► to adjust the projected image appearance as required. Lamp Mode Select Normal or Eco from the lamp mode window.
5. Using On-Screen Display 82 Lamp Interval Lamp Interval determines the pe riod of time after which the lamp should be swap when lamp select is not Dual. Select from the following: Off , 1 w eek , 4 w eek and 2000H Menu Mode Select the Menu Mode to display.
5. Using On-Screen Display 83 Language Select the OSD language to be used. Select from the following: English German French Italian Spanish Sw ed is h Japanese Simplifi.
5. Using On-Screen Display 84 Installation The Installation tab contains menu opti ons for various setup conditions such as orienta- tion and remote sensor mode and is accessed throu gh the Setup menu. The following table lists all functions with a brief description.
5. Using On-Screen Display 85 I TEM D ESC RIPTION Control Panel Lock Set Control Panel Lock On/Off. Note: y This Control Panel Lock does not affect the remote control functions. y When the control panel is lo cked, pressing and holding the Exit button on the projector c abinet for about 10 seconds.
5. Using On-Screen Display 86 Desktop front Ceiling rear Ceiling front Desktop rear Communication Speed Select communication speed to set the baud rate of the conne ction.
5. Using On-Screen Display 87 Color Monochrome Display Time Sets the amount of time a menu is displayed. Select from the following: Manual – Menus stay on screen until the Menu button is pressed again. Auto 5 secs – Menu is displayed for 5 second s.
5. Using On-Screen Display 88 Background Background enables yo u to display a blue/black screen when there is no signal. The de- fault background is blue. Select from the following: Blue Black Logo Security See t Preventing the Unauthorized Use of the Proje c tor on page 57 .
5. Using On-Screen Display 89 DynamicBlack DynamicBlack enables you to improve the black level of the projector. Remote Sensor Set the operating range for the wireless remote control. Select from the following: Front/Back Front Back LAN Settings See LAN Settings on page 91 .
5. Using On-Screen Display 90 Select from the following: Normal Power-saving Note: The HTTP server functions are not available during Power-saving mode. The MONITOR OUT function is not av ailable during Power-saving mode. Control through the PC Control connect or and LAN mode is not available during Power-saving mode.
5. Using On-Screen Display 91 LAN Settings The LAN settings tab is acce ssed by using the Setup /Inst allation tab and contains ge n- eral LAN settings. The following table lists all functions with a description and the default setting. I TEM D ESCRIPTIO N DHCP Select either a static IP or DHCP IP setting by selecting the appropriate radio button.
5. Using On-Screen Display 92 Options The Options tab contains miscellaneous setup men u settings such as Power Manage- ment and Default Source Select an d can be accessed by using the Setup Menu. The following table lists all functions with a description and the default setting.
5. Using On-Screen Display 93 I TEM D ESCR IPTION Color System Select the default Color System to use for Video or S-Video input. Range: Auto, NTSC, PAL, SECAM (see page 95 ). Filter Message Set this item to on to have the projector display a me ssage when the air filter needs servicing.
5. Using On-Screen Display 94 Select from the following: Off 5 minutes 10 minutes 20 minutes 30 minutes Screen Trigger Set Screen Trigger to On to enable the projector to automatically lower the projection screen when powering on.
5. Using On-Screen Display 95 Last – Uses the most recently used ima ge source. Auto – Auto detects the default image sou rce. Computer1/2/3 – Uses Computer1, 2 or 3 as the default image source. Component – Uses last component a s the default image source.
5. Using On-Screen Display 96 u Information Menu Descriptions and Functions The information menu provides o nly screens to access details quickly. The Information menu contains four distinct tabs. Usage Time The Usage Time tab displays information about lam p usage and remaining lamp life.
5. Using On-Screen Display 97 Source The Source tab displays various sou rce and frequency values at a glance. The following table lists all items with a descri ption. I TEM D ESCRIPTION Input Terminal Displays the Input Terminal that is presently being used.
5. Using On-Screen Display 98 LAN The LAN tab displays LA N settings as previously defined (see LAN Settings on page 89 )..
5. Using On-Screen Display 99 Version The Version tab displays all the version and pr oduct details of the projector and associ- ated software. NP4000 Version Screen: NP4001 Version Screen:.
5. Using On-Screen Display 100 The following table lists all items with a descri ption. I TEM D ESCRIPTION Product Displays Product ID. Serial Number Display s projector Serial Number. Firmware Displays Firmware version and Color Wheel currently installed (4-seg or 6-seg).
5. Using On-Screen Display 101 v Reset Menu Descriptions and Functions Occasionally, circumstances may re quire that factory defaults are reset, for demonstration purposes for example, or when co mponents are replaced. The Reset menu contains options for returning setting s to the factory default and is accessed via the Main menu.
102 6. Maintenance n Cleaning the projector Cleaning the Cabinet Refer to the following guide to clean the projector cabinet. 1. Wipe off dust with a clean dampened cloth. 2. Moisten the cloth with warm water and mild detergen t and wipe the cabinet. 3.
6. Maintenance 103 Cleaning the Filters The projector uses three f ilters to keep the fans f ree of dust and other pa rticles, and should be cleane d every 500 hours of operati on. In dustier environments, it is reco m- mended to clean the filters more frequently.
6. Maintenance 104 3. The rear filter can be accessed as shown. Once the filters are clean ed, please reset the filter hours via the Clear Filte r Hours op- tion in the v Reset Menu Descriptions and Functions on page 101 . Note: Using the projector without t he air filter fitted inside, dirt and dust are sucked into the projector, causing failure.
6. Maintenance 105 o Replacing Consumable Parts During the course of norm al usage, consumable part s become worn out resulting in reduced performance. The following guide s detail how to replace the vario u s consumable part s within the projector quickly and safely.
6. Maintenance 106 3. Insert replacement foam and press down firmly. 4. Replace the filter covers by pushing gently in the direction shown. Once the filters are replaced, plea se reset the filter hours via the Clear Filter Hours op- tion in the v Reset Menu Descriptions and Functions on page 101 .
6. Maintenance 107 Replacing the Lamps When a lamp reaches the end of it’s usable lif e, the followi ng message is displa yed. Re- place the lamp. The projection lamps sho uld be replaced when they burn out. They should only be re- placed with a certified replacem ent part, contact your local dealer if unsure.
6. Maintenance 108 To replace the lamp, refer to the following. 1. Loosen the screw on the lamp cover (A), and remove the lamp cover as shown (B). 2. Loosen the two captive screws (A) on the lamp module. Lift the module handle up (B) in the direction shown.
6. Maintenance 109 Resetting the Lamp Hours Counter After replacing the lam p(s), the lamp hour co unter(s) should be reset to zero. Refer to the following guide: 1. Press the Menu button on the OSD control panel or Re- mote Control to open the Main menu.
110 7. Appendix n Using the Optional Remote Mouse Receiver (NP01MR) The optional remote mouse receiver enables you to operate your compute r’s mouse func- tions from the remote control. It is a great convenience for clicking through you r computer- generated presentations.
7. Appendix 111 When connecting using the USB terminal The mouse receiver can only be used with a Microsoft Windows 98/Me/XP*/2000 PC system or a Mac OS X 10.
7. Appendix 112 o Troubleshooting Indicator Messages Several indicator messages are u sed by the projector to alert users of problems with setup or internal parts.
7. Appendix 113 The Lamp LEDs P ROJECTOR S TATUS LED C ONDITION LED S EQUENCE P ROJECTOR C ONDITION Lamp off Off Off Lamp off End of the lamp life Red blink 0.5 secs on 0.5 secs off Replace lamp (see notes below) No lamp Red 1 time blink (repeatedly) 0.
7. Appendix 114 Common Problems and Solutions These guidelines provide tips to deal wit h problems you may encounter while using the projector. If the problem remains unsolv ed, contact your dealer for assistance. Often the problem is something as simple as a lo ose connection.
7. Appendix 115 p Image Problems Problem: No image appears on the screen 1. Verify the settings on your notebook or desktop PC. 2. Turn off all equipment and power up again in the correct order. Problem: The image is blurred 1. Adjust the Focus on the projector.
7. Appendix 116 Lamp Problems Problem: There is no light from the projector 1. Check that the power cable is securely con nected. 2. Ensure the power source is good by testing with another electrical device. 3. Restart the projector in the correct order and check that the Power LED is green.
7. Appendix 117 Audio Problems Problem: There is no sound 1. Adjust the volume on the remote control. 2. Adjust the volume of the audio source. 3. Check the audio cable connection. 4. Test the source audio output with other speakers. 5. Have the projector serviced.
7. Appendix 118 q Having the Projector Serviced If you are unable to solve the problem, you shoul d have the proje c tor serviced. Pack the pro- jector in the original carton. Include a d escripti on of the problem and a checklist of the steps you took when trying to fix the problem.
119 8. Specifications n Projector Specifications This section provides technical informat ion about the proj ector's performance. Optical Specifications I TEM D ESCRIPTIO N Projection syst em Sin.
8. Specifications 120 Electrical Specifications I TEM D ESCRIPTIO N Inputs 1 Analog RGB (Mini D-Sub 15P), 1 An alog RGB R/Cr, G/Y, B/Cb, H, V (BNC x 5), 1 Digi tal RGB (DV I-D 24P), 1 Compone nt Y, Cb.
8. Specifications 121 I TEM D ESCRIP TION Power Cons umption 655W in Dual Lamp Norm al mode / 580W in Dual Lamp Eco mode 350W in Sin gle Lamp Normal m ode / 315W in Single Lamp Eco mode < 30W in St.
8. Specifications 122 Regulations UL/C-UL Approved (UL 60950-1, CSA 60950 -1) Meets FCC Class B require ments Meets DOC Canada Class B requirem ents Meets AS/NZS CISPR.
8. Specifications 123 o Cabinet Dimensions.
8. Specifications 124 p Pin Assignments of Mini D-Sub 15 Pin Input Connector Signal Levels Video signal: 0.7Vp-p (Analog) Sync signal: TTL level P IN N UMBER RGB S IGNAL (A NALOG ) YC B C R S IGNAL 1. Red Cr 2. Green or Sync on Green Y 3. Blue Cb 4. Ground 5.
8. Specifications 125 q Compatible Input Signal List The following table shows com patible signal types, their resolution and freque ncy refresh rates. Horizontal: 15 kHz, 31kHz to 90 kHz Vertical: 50 Hz to 85 Hz S IGNAL R ESOLUTION ( DPI ) F REQUENCY R EFRESH R ATE (KH Z ) F REQUENCY R EFRESH R ATE (H Z ) NTSC – – 15.
8. Specifications 126 S IGNAL R ESOLUTION ( DPI ) F REQUENCY R EFRESH R ATE (KH Z ) F REQUENCY R EFRESH R ATE (H Z ) * VESA D 1280 x 768 47.80 60.00 * VESA D 1280 x 768 60.30 75.00 * VESA D 1280 x 768 68.60 85.00 * VESA D 1280 x 800 49.70 60.00 * VESA D 1280 x 800 62.
8. Specifications 127 Note: Images above flagged with "D" are supported by digital signal. Images above flagged with “*” are supported by the NP4001 only. An image with higher or lower resolution than the projector’s native resolution (1280 x 768: NP4001, 1024 x 768: NP4000) will be compressed.
8. Specifications 128 r PC Control Codes and Cable Connections The following table shows PC functi ons and their associated code data. F UNCTION C ODE D ATA POWER ON 02H 00H 00H 00H 0 0H 02H POWER OFF.
8. Specifications 129 Note: Depending on the equipment, a lower baud rate may be recommen ded for long cable runs. PC Control Connector (DIN-9P) Note: 1. Pin 1, 4, 6 and 9 are not used. 2. Jumper “Request to Send” and “Clear to Send” together on both ends of the cable to simplify t he cable connection.
8. Specifications 130 s Screen Trigger When the projector is po wered ON the screen trigger output sends a low voltage trigger to the screen controller and the scre en will go down . When the projector is powered OFF the screen trigger stops sendin g a low voltage tri gger to the screen controller and the screen will go up.
8. Specifications 131 t Operation Using HTTP Browser Overview The use of HTTP server functions will allow control of the projecto r from a web browser without the installation of special software. Pl ease be sure to use “Microsoft Internet Ex- plorer 4.
8. Specifications 132 When the IP address of the projecto r is 192.168.73.1 , access is gained to the HTTP server functions by specifying http://192 .168.
8. Specifications 133 Mail Alert Mail: Click “Enable” to ena ble Alert Mail featur e. This option notifies you r computer of an error message via e-mail when using wire d LAN. The error message will be noti- fied when the projector lamp has reached the end of its usable life or an erro r occurs in the projector.
8. Specifications 134 Structure of the HTTP Server Once the projector is connected to a network and configu red correctly, the following screen is displayed thro ugh the web browser.
8. Specifications 135 F UNCTION S ETTING D ESCRIPTIO N Source Select Panel Computer 1 – Switches to the COMPUTER 1 IN connector Computer2 – Switches to the COMPUTER 2 IN connector Computer3 – Sw.
8. Specifications 136 u 15 Pin GPIO Control Type: 15Pin D-SUB black female type P IN N O . S HORT /O PEN F UNCTION 14 SHORT OPEN EXTERNAL CONTROL MODE ON EXTERNAL CONTROL MODE OFF 5 SHORT OPEN POWER O.
137 9. Troubleshooting Check List Before contacting your dealer or service perso nnel, check the following list to be sure repairs are needed also by referri ng to the o Troubleshooting section on page 112 of your user’s manual. This checklist below will help us solve your problem more efficiently.
9. Troubleshooting Check List 138 Other Remote con trol does not work. No obstacles betw een the sensor of the projector and the remote control. Projector is placed near a fluorescent light that can disturb the infrared remote control s. Batteries are new and are not reversed in installa- tion.
9. Troubleshooting Check List 139 Signal cable NEC standard or other manu facturer’s cable? Model number: Length: inch/m Distribution amplifier Model number: Switcher Model number: Adapter Model num.
デバイスNEC NP4001-10ZLの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
NEC NP4001-10ZLをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNEC NP4001-10ZLの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。NEC NP4001-10ZLの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。NEC NP4001-10ZLで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
NEC NP4001-10ZLを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNEC NP4001-10ZLの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、NEC NP4001-10ZLに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNEC NP4001-10ZLデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。