NewAirメーカーAC 12000Eの使用説明書/サービス説明書
ページ先へ移動 of 16
PLEASE READ AND SAVE THESE INSTRUCTIONS NewAir AC ‐ 12000E, AC ‐ 12000H Portable Air Conditioner Owner’s Manual k0045.
BEFORE USE GENERAL SAFETY INSTRUCTIONS: • AL W A YS OPERA TE THE UNIT IN AN UPRIGHT POSITION AND PLACE IT ON A FLA T , LEVEL SURF ACE A T LEAST 14 INCHES A W A Y FROM ANY OTHER OBJECTS (Fig 1 & 4). • DO NOT PLACE OBJECTS ON THE UNIT , AND DO NOT COVER OR OBSTRUCT THE INLET OR OUTLET GRILLS (FIG.
PARTS LIST Front: Back: 1. Control panel 2. Louvers 3. Carrying handle 4. Casters 5. Air filter 6. Air inlet 7. Cord storage 8. Exhaust air outlet 9. Rubber plug / drainage point Accessories: 10. Exhaust hose 11. Hose adaptor (goes over the hose and into the window kit) 12.
INSTALLATION INSTRUCTIONS Installing the Exhaust Hose and Window Kit: FIG.5 Wall or Window Window Kit Adapter 1. Open the window and insert the window kit into the open gap. 2. Close the window until the window kit is held securely. This technique may also be used for sash windows.
Positioning the Exhaust Hose: • Insert the exhaust hose into the back of the unit and tighten it into place. • Avoid kinks and bends in the exhaust hose.
Installing the Activated Carbon Filter: 1. Remove the filter frame from the unit. 2. Separate the filter from the filter frame. 3. Remove the activated carbon filter from its plastic bag. 4. Insert the activated carbon filter into the filter frame. 5.
OPERATING INSTRUCTIONS Control Panel 1. Fan speed (ventilation) button 2. Timer button 3. Display window 4. Remote control receiver 5. Heater indicator (for AC-12000H only ) 6. Mode selection button 7. Automatic mode indicator 8. Cooling mode indicator 9.
Setting the Mode/Function: 1. Press the MODE button to select the desired mode (cooling, fan or heating). Heating mode is only available on the AC-12000H. 2. The selected mode’s indicator light will turn on. Setting the Temperature: 1. Press the “Up” or “Down” butt on to change the set temperature.
Heating Mode: When the air conditioner is in heating mode, ambient warm ai r is recycled and used to heat your immediate area. The exhaust pipe will stil l need to be fitted onto the unit in order for the cold air to be removed . When in heating mode, the machine can be set on HIGH or LOW speed.
DRAINING THE UNIT During the cooling process, some water will be extracted from the air and stored within the unit’s water reservoir. If the water reservoir is full, both the compressor and motor will stop and t he unit will beep (press any button to stop the beeping sound).
For Continuous Drainage: • Remove the rubber plug from the drainage port and retain it for future use. • Connect the drain tube to the drainage port as shown (fig. 17). • Connect the other end of the hose to a drain. FIG.16 • The drain tube may be extended by adding an extension tube with a suitable connector.
For Heating Mode: While using the heating function, please note the following: 1. In order to properly exhaust cool air, make sure the exhaust hose and window kit are properly installed (refer to page 6 for instructions). 2. Set up the air conditioner for continuous drai nage using the drain tube (refer to page 13 for instructions).
MAINTENANCE INSTRUCTIONS Always unplug the air conditioner from the power supply before cleaning. To maximize the efficiency of the air conditioner, regularly clean the unit.
TROUBLESHOOTING The air conditioner does not work. y Is the air conditioner plugged in? y Is the power outlet functioning correctly? y Is the full water tank indicator light flashing? y Is the ambient room te mperature lower than the set temperature? The unit does not produce adequate cooling.
TECHNICAL SPECIFICATIONS Model Number: AC-12000E AC-12000H Power Consumption for Cooling* 1166W / 11A 1166W/11A Power Consumption for Heating * N/A 1054W/10.
LIMITED MANUF ACTURER’S W ARRANTY This appliance is covered by a limited manufac turer ’ s warranty . For one year from the original date of purchase, the manufacturer will repair or replace any p.
デバイスNewAir AC 12000Eの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
NewAir AC 12000Eをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNewAir AC 12000Eの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。NewAir AC 12000Eの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。NewAir AC 12000Eで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
NewAir AC 12000Eを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNewAir AC 12000Eの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、NewAir AC 12000Eに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNewAir AC 12000Eデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
