Niles AudioメーカーMSU250の使用説明書/サービス説明書
ページ先へ移動 of 24
MSU250 INFRARED MAIN SYSTEM UNIT MSU250 B LENDING H IGH F IDELITY AND A RCHITECTURE ® INST ALLA TION & OPERA TION GUIDE DS00328ACN_MSU250.qxp 2/27/04 10:10 AM Page 24.
T ABLE OF CONTENTS Introduction 1 Features and Benefits 2 MSU250 Parts Guide 4 Installation Considerations 5 Installation 8 T esting the IR Extender System 1 1 Power Status 13 T r ouble- Shooting 16 S.
2 I NFRARED MAIN S YSTEM UNIT Features and Benefits The MSU250 offers a number of improvements over other IR Extender Main System Units: • Universal system—compatible with virtually all brands of A/V equipment and remote controls. • Accommodates two IR sensors or keypads.
3 3-30V AC/DC STATUS IN I NFRARED MAIN S YSTEM UNIT Niles IR Flasher MSU250 WS100 IR Sensor Power , IR data, status signal and ground via category 5 wire Stereo Receiver 12VDC power supply (supplied w.
3-30V AC/DC ST A TUS IN 4 I NFRARED MAIN S YSTEM UNIT MSU250 Parts Guide 1. 12VDC Jack – Provides 12 volt DC power to MSU via a regulated power supply . 2. IR Flasher Outputs – 3.5mm jacks provide output for either single or dual (MF1, MF1VF , MF2, MF2VF) low-level flashers.
Installation Considerations Placement of the MSU250 Place the MSU250 conveniently close to the equipment it will be controlling. Generally , the unit is placed in a concealed location because its controls and indicators are only used dur- ing installation.
Wiring From every IR Sensor location you must “home-run” a category 5 cable back to the MSU250. Home run means that an individual cable is connected between each IR Sensor and the MSU250 (Figure 4). 6 I NFRARED MAIN S YSTEM UNIT “TECH TIP” Wire size is expressed by it’ s A WG (American Wire Gauge) num- ber .
IntelliPad Wiring When you are placing both a IntelliPad and a sensor (or two keypads) in one room you may “daisy-chain” using a single cable. A cable is run between the keypad and the sensor and a single cable is run from either the sensor back to the MSU250.
3-30V AC/DC STATUS IN Installation Before you begin, make sure that the sensor/keypad cables, the flasher cables and the 12VDC power supply cable will all reach the proposed location of the MSU250. Mark the cables with labels describing where the cable originates (rather than which terminal on the MSU250 it should connect).
9 I NFRARED MAIN S YSTEM UNIT STEP DESCRIPTION 1. Connect and test the pow er supply . If it tests OK, unp lu g the connector from the power socket and proceed. A) Plug the supplied 12VDC power supply into an unswitched 120 volt AC outlet, 50-60 HZ . B) Plug the connector into the socket marked “Power” on the MSU250.
10 I NFRARED MAIN S YSTEM UNIT STEP DESCRIPTION BE SURE TO OBSERVE PROPER POLARITY WHEN EXTENDING THE FLASHER WIRE. The wire lead marked with a gray stripe is positive ( + ) ; the unmarked lead is negative (- ) . 3. T est for shorts and interference. A) Reconnect the power supply .
11 I NFRARED MAIN S YSTEM UNIT T esting the IR Extender System T est your IR Extender system by following the three principal guidelines: 1. All components can be operated. T est all of your remote controls for all of your equipment. 2. Operation is consistent.
12 I NFRARED MAIN S YSTEM UNIT 12 V olt T rigger Output The Niles MSU250 provides a 12VDC output that can be trig- gered one of two ways: 1. The presence of status voltage on the 12VDC status input jack. 2. Discrete infrared on and off commands. The discrete on and off commands are available for download at: www .
13 I NFRARED MAIN S YSTEM UNIT Power Status — Introduction T o properly wire an IntelliPad to the MSU250, refer to Figure 5. By providing 3-30 volt AC/DC to the status input jack of your MSU250 you can send a status signal to sensors or an IntelliPad without running any additional wiring.
14 I NFRARED MAIN S YSTEM UNIT Extending the Cable If you must extend the cable from the wall adapter to the MSU250’ s status input jack be sure to maintain correct polari- ty . The tip of the plug should be positive (+) and the sleeve negative (-).
OUTPUT TO MSU POWER STATUS +1 2V DC IRH61 0 I R E X PA N S I O N H U B IN PUT 1 IN PUT 4I N PUT 5I N PUT 6 IN PUT 2 IN PUT 3 1 2VDC Power supply (Not Supplied) plugged into a switched outlet Niles sto.
System Expansion System expansion is easily achieved (Figure 9) through the use of an IRH610 Infrared Sensor Expansion Hub. Please see your authorized Niles dealer or refer to the IRH610 manual for details. T roubleshooting Guidelines There are three basic problems which prevent proper opera- tion.
17 I NFRARED MAIN S YSTEM UNIT 2. Optical or Electromagnetic Interference Direct sunlight, reflections, neon signs and other sources of infrared light or television sets, light dimming controls and other sources of electromagnetic fields can induce noise and interference into your IR extender system.
18 I NFRARED MAIN S YSTEM UNIT 3. Optical Feedback Loop If you have an IR sensor in the same room as a flasher , and you have some low-level noise or interference, an optical feedback loop can occur which will interfere with proper operation. Symptoms can include: poor range, intermittent operation or no operation.
19 I NFRARED MAIN S YSTEM UNIT Specifications IR System Compatible with virtually all brands of remotes using carrier frequencies between 26 and 1 05kHz. W iring Requir ements Individual home-runs of category 5 cable from each sensor/keypad. Unit Dimensions 5-11/16” wide x 1-1/4” high x 2” deep.
20 I NFRARED MAIN S YSTEM UNIT Addendum: Using the MSU250 with the IntelliControl ® automation system 3-30V AC/DC STATUS IN 150 OHm Resistor Using the MSU250 with the IntelliControl Home Theater auto.
21 I NFRARED MAIN S YSTEM UNIT Notes DS00328ACN_MSU250.qxp 2/27/04 10:10 AM Page 21.
22 I NFRARED MAIN S YSTEM UNIT Notes DS00328ACN_MSU250.qxp 2/27/04 10:10 AM Page 22.
Ni les Audio Corpora tion www .nilesaudio.com 1 233 1 S.W . 1 30 Street Miami, Florida, 3 3 18 6 T el: (305) 238-4373 Fax: (305) 238-0 1 85 © 2004 Niles Audio Corporation. All rights reserved. Niles, the Niles logo, IntelliPad and Blending High Fidelity and Architecture are registered trademarks of Niles Audio Corporation.
デバイスNiles Audio MSU250の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Niles Audio MSU250をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNiles Audio MSU250の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Niles Audio MSU250の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Niles Audio MSU250で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Niles Audio MSU250を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNiles Audio MSU250の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Niles Audio MSU250に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNiles Audio MSU250デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。