Nilfisk-ALTOメーカーS-8の使用説明書/サービス説明書
ページ先へ移動 of 22
User's Manual LTO R www .altoproaudio.com V ersion 2.0 Dec. 2002 English 8- CHANNEL MIXING CONSOLE S-8.
1 SAFETY RELA TED SYMBOLS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Protective Ground T erminal AC mains (Alternating Current) Hazardous Live T erminal ON: Denotes the product is turned on. OFF: Denotes the product is turned off. W ARNING Describes precautions that should be observed to prevent the possibility of death or injury to the user .
2 PREF ACE Dear Customer: Thank you very much L TO AUDIO TEAM Thank you for choosing the L TO S-8 8-Channel Mixing Console, which is the result of our L TO AUDIO TEAM's endeavours.
3 T ABLE OF CONTENTS 1.INTRODUCTION.........................................................................................................................................................4 2.FEA TURES..................................................
4 Y our S-8 is a 8-channel mixer and it is one of the most popular compact mixing consoles in the world. In fact it has been sold already in terms of thousands of units worldwide. Despite its compact dimensions, great performances and sound quality are insured thanks to the specification of the components used and the building quality .
5 5 Input for Microphone and line provided with balanced 1/4" jack and XLR. Channel 5 features stereo Line input 1 additional input for Line level signal provided with balanced TRS 1/4" jack.
6 3. READY TO ST ART? 3.1 Please check the AC V oltage available in your Country before connecting your S-8 to the AC socket. 3.2 Be sure that the main power switch is turned off before connecting the Mixer to the AC socket. Also, you should make sure that all Input and Output Controls are turned down.
7 4. CONTROL ELEMENTS 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 MIC 1 MIC 2 MIC 3 MIC 4 LINE IN 1 TRIM LINE IN 2 TRIM LINE IN 3 TRIM LINE IN 4 TRIM BAL OR UNBAL BAL OR UNBAL BAL OR UNBAL BAL OR UNBAL BAL OR UNBAL.
8 1 2 3 4. CONTROL ELEMENTS 4.1 The mono MIC/LINE channels 4 4.2 INPUT LEVEL setting This Control is provided with 2 different indication rings: One is for the Microphone and the other for the Line levels.
9 5 4.4 STEREO INPUTS These are Channel 5 through 8. They are organised in stereo pair (5&6 pair also features XLR Mic Input) and they are provided with 1/4" TRS phone sockets. If you connect only the left jack, the input will operate in mono mode.
10 9 4.6 AUX SENDS 10 4.7 P AN This is the P ANORAMA control, or balance control. Y ou can adjust the stereo image of the signal via this Control. Keep this control in center position and your signal will be positioned in the middle of stage.
11 4.1 1 MASTER SECTION 14 - MAIN MIX LEVEL This Control sets the amount of signal sent either to the Main Out socket or to the T ape Output. 15 - LED METER This stereo 12 segments Led Meter will indicate the level of the overall output signal.
21 23 22 1 2 STEREO AUX RETURN AUX SEND 2-TRACK IN/OUT T APE IN T APE OUT LEFT RIGHT L R 1 2 LEFT(MONO) RIGHT 21 - 2-TRACK IN/OUT Use the T ape input if you wish to listen to your Mix from a T aper Re.
13 4.12 REAR P ANEL DESCRIPTION 4 Use only with a 250V fuse POWER ON OFF PHANTOM RA TED POWER CONSUMPTION: 18W LEFT RIGHT RIGHT LEFT MAIN MIX OUTPUT (BAL/UNBAL) CONTROL ROOM OUTPUT CAUTION: REPLACE WI.
T urn down all Input and Output Gain Controls. Connect phantom powered microphones before switching on the +48V olt Phantom Power switch. If you have a power amplifier connected to your S-8 set the Level of the amplifier at no more than 70%. Now , set the CONTROL ROOM/PHONES level at no more than 50%.
15 Strain Clamp Sleeve Ti p Ring Sleeve=Ground/Screen Ring=Return Signal T ip=Send Signal Use for Pre-Gain Channel Inserts 1/4" Stereo (TRS) Jack Plug Strain Clamp Sleeve Ti p Ring Sleeve=Ground/.
16 Sleeve=Ground/Screen T ip=Signal Sleeve=Ground/Screen Ring=Return Signal (Connected together) T o Channel Insert T o T ape or FX Input 'T apped' Connection Direct Output Lead (Enables the.
17 6. FOR THE EXPERTS WHO W ANT TO KNOW MORE Modification on mono and stereo channels Before Disconnect the POST route Aux (PRE) POST After Aux (PRE) POST Solder the PRE route As we have told you previously in this Manual, the Aux Send 2 Control both on Mono and stereo channels is factory wired as POST -F ADER.
18 7. SYSTEM BLOCK DIAGRAMS.
19 8. TECHNICAL SPECIFICA TION Mono input channels Stereo input channels Line input Balanced Frequency response 10Hz to 55kHz, 3dB + Distortion (THD & N) 0.
20 9. W ARRANTY 1. W ARRANTY REGISTRA TION CARD T o obtain Warranty Service, the buyer should first fill out and return the enclosed W arranty Registration Card within 10 days of the Purchase Date.
SEIKAKU TECHNICAL GROUP LIMITED No. 1, Lane 17, Sec. 2, Han Shi W . Road, T aichung, 401 T aiwan http://www .altomobile.com T el: 886-4-22313737 email: info@altomobile.
デバイスNilfisk-ALTO S-8の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Nilfisk-ALTO S-8をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNilfisk-ALTO S-8の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Nilfisk-ALTO S-8の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Nilfisk-ALTO S-8で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Nilfisk-ALTO S-8を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNilfisk-ALTO S-8の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Nilfisk-ALTO S-8に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNilfisk-ALTO S-8デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。