NortelメーカーCallPilot 703tの使用説明書/サービス説明書
ページ先へ移動 of 72
CallPilot Release 4.0 Document Number: 555-7101-226 Document Version : Standard 1.04 October 2006 703t Server Hardware Installation.
Standard 1.04 2 CallP ilot Copyright © 2006 Nortel Networks. All Rights Reserved. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are be lieved to be a ccurate and reliabl e, but are presented without express or implied warranty.
October 2006 703t Server Hardware Insta llation 3 CRYSTAL REPORTS is a trademark of Seaga te Software Inc. EUDORA is a trademark of Qualcomm. eTrust and InoculateIT are trademarks of Computer Associates Think Inc.
Standard 1.04 4 CallP ilot WINZIP is a trademark of Nico Mark Computing, Inc. XEON is a tr ademark of Intel, Inc. All other trademarks and registered tr ademarks are the property of their respective owne rs.
October 2006 703t Server Hardware Insta llation 5 があります。この場合には使用者が適切な対策を取るように要求されることがあ ります。 This is a Class A product b ased on th e standard of the Voluntary Contro l Council for Interference by Informa tion Technology Equipment (VCCI).
Standard 1.04 6 CallP ilot.
703t Server Hardware Insta llation 7 Publication history October 2006 Standard 1.04 of 703t Server Hardware Installation is issued for general rel ease for CallPilot 4.0. Septem ber 2006 Standard 1.0 3 of 703t Server Hardware Installation is issued for general release for CallPilot 4.
8 CallP ilot Publication history Standard 1.04.
703t Server Hardware Insta llation 9 Task List To unpac k the equip ment ............ ............. .......... ............. ............. .. 37 To remov e the side panel ......... .......... ............. ............ ............. ...... 39 To inspect the serv er interio r .
Task List Standard 1.04 10 CallP ilot.
703t Server Hardware Insta llation 11 Contents 1 How to get Help 13 2 703t server description 15 Server features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Slot assignments . . . . . . . . . . . . . .
Contents Standard 1.04 12 CallP ilot.
703t Server Hardware Insta llation 13 Chapter 1 How to get Help This section explains how to get help for Nortel products and services. Getting Help from the Nortel Web site The best way to get technical support for Nortel products is from th e Nortel Technical Support Web site: http://www.
How to get Help Standard 1.04 14 CallP ilot Outside North America, go to the follo wing Web site to obtain the phone number for your region: http://www.
703t Server Hardware Insta llation 15 Chapter 2 703t server description In this chapter Server fe atures 16 Slot assignme nts 23 Network connect ivity 25 Supported peripheral d evices 30 Referenc e do.
703t server de scription Standard 1.04 16 CallP ilot Server features This section provides a general overview of the 703t server. Server dimensions Height chassis only: 420 mm (16.75 in.) with chassis feet: 440 mm (17.5 in.) Width chassis only: 215 mm (8 .
October 2006 703t server description 703t Server Hardware Insta llation 17 Environmental specifications Environmental condition Specification Operating temperature 10 ° C to 35 ° C (50 ° F to 95 ° F) Maximum rate of change must not exceed 10 ° C (50 ° F) per hour.
703t server de scription Standard 1.04 18 CallP ilot Front panel features The following diagram sho ws the 703t server’s fro nt panel features: G101759 CD-R OM drive CD dra wer eject b utton T ape d.
October 2006 703t server description 703t Server Hardware Insta llation 19 The table below describes the parts th at are identified in the preceding diagram: Part Funct ion Reset button Triggers a hardware (cold) reset. Do not use this button to perform a server restart.
703t server de scription Standard 1.04 20 CallP ilot IDE CD-ROM drive (5.25 in.) Enables you to use the CallPilot software and documentation CD-RO Ms. CD drive eject button Opens the CD-ROM drawer. Push the button again to close the drawer. Backup tape drive Allows backup of hard drive data.
October 2006 703t server description 703t Server Hardware Insta llation 21 Rear panel diagram The following diagram sho ws the 703t server’s rear panel features: Note: For more information, see “S lot assignments” on page 23.
703t server de scription Standard 1.04 22 CallP ilot The table below describes the parts th at are identified in the preceding diagram: Part Color AC power supply conn ector (450 W non ho t-swap power.
October 2006 703t server description 703t Server Hardware Insta llation 23 Slot assignments The slot assignment tab les show the physical l ocation of boards inside th e server, rel ative to other.
703t server de scription Standard 1.04 24 CallP ilot Slot definition and numbering In the following table, the term “slot” re fers to the available slot openings in the chassis, not the PCI connectors inside the server. The slots are numbered from the bottom of the server to the top.
October 2006 703t server description 703t Server Hardware Insta llation 25 Network connectivity This section describes how the 703t se rver can be integrated into your network.
703t server de scription Standard 1.04 26 CallP ilot Sample network setup: Meridian 1 The Meridian 1 switch can be one of the following: Option 11C or Option 11C Min i using fiber conn ections Option 51C Option 61C Options 81 an d 81C The following diagram sho ws a CallPilot 703t server network setup wi th a Meridian 1 switc h.
October 2006 703t server description 703t Server Hardware Insta llation 27 Sample network setup: Succession 1000 The following diagram sho ws a CallPilot 703t server network setup wi th a Succession 1.
703t server de scription Standard 1.04 28 CallP ilot In the previous diagra m, the telephony LAN (TLAN) p rovides IP connectivity between the Succession 1000 system and the i2004 Internet phonesets.
October 2006 703t server description 703t Server Hardware Insta llation 29 Network requirements Appropriate networking equipment must be available for the ELAN and the optional CLAN if it is used. The ELAN (and the optional CLAN if used ) must be properly configured for correct CallPilot operation.
703t server de scription Standard 1.04 30 CallP ilot Supported peripheral devices This section identifies external devi ces th at are suppo rted by the 70 3t server.
October 2006 703t server description 703t Server Hardware Insta llation 31 Reference documents Fundamentals CallPilot Fundamentals Guide (555-7101-010) Planning and Engineering Data Networking for V o.
703t server de scription Standard 1.04 32 CallP ilot.
703t Server Hardware Insta llation 33 Chapter 3 Preinstallation requirements In this chapter Installation overvi ew 34 Unpacking the 703t se rver 37 Removing the side cover 39 Inspecting the ser ver i.
Preinstallation re quirements Standard 1.04 34 CallP ilot Installation overview Introduction This section provides an overview of the steps required t o install the 703t server and peripheral devices. For detailed instructions, see Chapter 4, “Installing the server and conn ecting the peripheral devices.
October 2006 Preinstallatio n requirements 703t Server Hardware Insta llation 35 5 Place the 703t server in th e chosen location (see page 48). ❒ 6 Set the DIP switches on the modem (see page 51). ❒ 7 Connect the 703t server and d evices as follows: Connect the monitor, keyboard, and mouse (see page 55).
Preinstallation re quirements Standard 1.04 36 CallP ilot Conventions for warnings You may encounter the follo wing types of warnings in this guide. Do not ignore them. . DANGER Risk of electric shock Warns you of an immediate elect rical haza rd, which, if not avoided, will result in shock, serious injury, or death.
October 2006 Preinstallatio n requirements 703t Server Hardware Insta llation 37 Unpacking the 703t server Introduction Follow this procedure to unpack the server and peripherals. To unpack the equipme nt 1 Carefully open the car dboard cart on containing the serve r.
Preinstallation re quirements Standard 1.04 38 CallP ilot 5 Save all packing mate rials and cart ons in case you must re turn an y equipment t o the carrier. What’s next? Remove the server sid e cover so that you can inspect the interior of the server.
October 2006 Preinstallatio n requirements 703t Server Hardware Insta llation 39 Removing the side cover Introduction This section describe s how to remove the server side co ver so that you can work with the interior comp onents. Th e side cover is on the server’ s left side when the front of the server is facing you.
Preinstallation re quirements Standard 1.04 40 CallP ilot The following diagram sho ws how to remove th e side panel. See the instructions for removal below. 1 Place the server on its side on your working sur face. 2 Turn the two thum bscrews on th e back of the server co unter-clockwise to loosen them .
October 2006 Preinstallatio n requirements 703t Server Hardware Insta llation 41 4 Use one hand to pull the t op edge of the cover away from t he server to disengage the top row of tabs on the cover from the no tches in the chassis. 5 Use both hands t o lift the cover upward to disen gage the bott om row of tabs from the no tches in th e chassis.
Preinstallation re quirements Standard 1.04 42 CallP ilot Inspecting the server interior Introduction Before you install the server, you sh ould perform a visual i nspection for loose components, foreign matter, or shipping damage inside the server. To inspect the server interio r 1 Ensure that all the cards are fully seated on the baseboard.
October 2006 Preinstallatio n requirements 703t Server Hardware Insta llation 43 Replacing the side cover Introduction When you are satisfied that th e server was not damage d during shipment, reinstall the side cover. To replace the side cover 1 Align the right edge of the server side cove r with the inside ledge a t the front of the se rver.
Preinstallation re quirements Standard 1.04 44 CallP ilot The following diagram shows how to: 1) align the tabs, 2) engage the cover, and 3) tighten the thum bscrews. What’s next? If you want to install the chassis feet on the bottom of the server, continue with “Installing the chassis feet” on pa ge 45.
October 2006 Preinstallatio n requirements 703t Server Hardware Insta llation 45 Installing the chassis feet Introduction You can install feet on the bottom of th e server. The feet stabilize the se rver and will help prevent the server from accidentally falling over on its side.
Preinstallation re quirements Standard 1.04 46 CallP ilot 1 Ensure th at the serv er is lay ing on its s ide, supp orted to give the server bottom fo ur to f ive inches cle arance above t he work surf ace. 2 Attach th e feet as shown in the pr eceding diagram.
703t Server Hardware Insta llation 47 Chapter 4 Installing the server and connecting the peripheral devices In this chapter Installing the server 48 Preparing t he modem 49 Connectin g peripherals to .
Installing the server and connecting the peri pheral device s Standard 1.04 48 CallP ilot Installing the server Before you install the 703t server, ensure that the chosen location mee ts the requirements identified in the “Site in spection checklist” provided in the Installation an d Configura tion Task List (555-7101-2 10).
October 2006 Installing the server and connecting the peripheral devi ces 703t Server Hardware Insta llation 49 Preparing the modem You require a modem to su pport remo te dial-up access to the CallPilot server. The modem also en ables Nortel technical support to connect to your CallPilot server for trouble shooting purp oses.
Installing the server and connecting the peri pheral device s Standard 1.04 50 CallP ilot The following diagram sho ws the key comp onents of the external modem, including the location and required se.
October 2006 Installing the server and connecting the peripheral devi ces 703t Server Hardware Insta llation 51 To set the modem DIP switches Use a pair of tweezers or a small screwdriver to set the DIP switc hes as described in the “Change to” co lumn of the following table: Note: ON is down.
Installing the server and connecting the peri pheral device s Standard 1.04 52 CallP ilot What’s next? Continue with “Connecting periphera ls to the server” on page 53. 6 OFF OFF Carrier Detect (CD) override OFF: The modem se nds a CD signal w hen it connects with anot her modem; it drops the CD on disconnect.
October 2006 Installing the server and connecting the peripheral devi ces 703t Server Hardware Insta llation 53 Connecting peripherals to the server This section describe s how to connec t the monitor, keyboard, mouse, and modem to the server.
Installing the server and connecting the peri pheral device s Standard 1.04 54 CallP ilot The diagram below shows the conn ectors for the power cord and the peripheral de vices on the 703t serv er.
October 2006 Installing the server and connecting the peripheral devi ces 703t Server Hardware Insta llation 55 To connect the mouse, keybo ard, and moni tor to the server 1 Place the monit or, keyboard, and mouse in the same locat ion as the server. 2 Plug the keyb oard and mouse int o the appropriat e PS/2 connecto rs on the chas sis rear p anel.
Installing the server and connecting the peri pheral device s Standard 1.04 56 CallP ilot 7 Connect the power cord to the mode m, and plug t he other e nd into a wall receptacle or power bar.
October 2006 Installing the server and connecting the peripheral devi ces 703t Server Hardware Insta llation 57 What’s next? Connect the server to the ELAN and CLAN hubs (if applicable). IF the server wi ll THEN be connected to the ELAN continue with page 58.
Installing the server and connecting the peri pheral device s Standard 1.04 58 CallP ilot Connecting the server to the ELAN Connect the CallPilot serv er to the Meridian 1 switch or Succession 100 0 system using the Embedded LAN (ELAN).
October 2006 Installing the server and connecting the peripheral devi ces 703t Server Hardware Insta llation 59 3 At the switc h, conne ct the E LAN networ k cable to an MAU ( Ethernet) transceiver . Then complete the conn ection from th e transcei ver to the switch.
Installing the server and connecting the peri pheral device s Standard 1.04 60 CallP ilot Connecting the server to the CLAN (optional) This section provides inst ructions to connect the server to th e Customer LAN (CLAN). Note: The CLAN connection is optional.
October 2006 Installing the server and connecting the peripheral devi ces 703t Server Hardware Insta llation 61 Installing the Nortel software feature dongle The software feature key is a security device that stores the unique serial number of the server.
Installing the server and connecting the peri pheral device s Standard 1.04 62 CallP ilot Requirements For installation, you require a Phillips No. 1 screwdriver. To install the software feature dongle 1 Ensure that there is no cable conn ected to the pa rallel port.
October 2006 Installing the server and connecting the peripheral devi ces 703t Server Hardware Insta llation 63 Connecting the server to power Before you begin Ensure that pro per power and ground ing are available for all t he power outlets serving the CallPilot server and its associated peripherals.
Installing the server and connecting the peri pheral device s Standard 1.04 64 CallP ilot Before you connect the server to th e power source, review the following diagram (and the warning that follows.
October 2006 Installing the server and connecting the peripheral devi ces 703t Server Hardware Insta llation 65 To connect the server to power 1 Plug the server ’s AC power cord in to the server’s rea r panel. 2 Plug the other end into a wall recept acle or power bar.
Installing the server and connecting the peri pheral device s Standard 1.04 66 CallP ilot.
703t Server Hardware Insta llation 67 Index Numerics 703t server CLAN connection, establishing 60 connections establishing 63 power 63 dimensions 16 ELAN connection, establishing 58 – 59 environment.
Index Standard 1.04 68 CallP ilot side cover removing 40 replacing 44 software feature key adapter 61 TLAN (Succession 1000) 27 dimensions, 703t server 16 DIP switches, setting modem 51 – 52 dongle .
October 2006 Index 703t Server Hardware Insta llation 69 monitor 30 mouse 30 power connecting server to 65 grounding, requirem ent 65 protocols, supported network 28 R rear panel, description 21 – 2.
Index Standard 1.04 70 CallP ilot.
.
703t Server Hardware Installation CallPilot Release 4.0 Document Number: 5 55-7101-226 Document Ve rsion : Standard 1.04 October 2006 To provide feedbac k or to r eport a problem in this do cument, go to http://www.nortel.c om/documentfeedback All Rights Reserved.
デバイスNortel Nortel CallPilot 703tの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Nortel Nortel CallPilot 703tをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNortel Nortel CallPilot 703tの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Nortel Nortel CallPilot 703tの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Nortel Nortel CallPilot 703tで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Nortel Nortel CallPilot 703tを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNortel Nortel CallPilot 703tの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Nortel Nortel CallPilot 703tに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNortel Nortel CallPilot 703tデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。