NuToneメーカーIMA4406の使用説明書/サービス説明書
ページ先へ移動 of 20
AM/FM RADIO/CD PLA YER INTERCOM SYSTEM MODEL: IMA-4406 SERIES MASTER ST A TION This booklet contains information for installing the master station. All system wiring and rough-in frames should be installed before mounting and wiring the master station.
2 INST ALLA TION T ABLE OF CONTENTS INST ALLA TION P AGE Contents of Carton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Precautions and Guidelines .
CONTENTS OF CARTON Check ( 3 ) for the following IMA-4406 carton contents. o IMA-4406 master station o Terminal board o T ransformer cover o H ardware bag assembly containing: 2- shoulder screws 12 - No.
MOUNTING THE TERMINAL BOARD 1. Remove and clean any drywall debris or dust from the rough-in before beginning installation. 2. Refer to Figure 1. Locate the terminal board in the left rear section of the rough-in frame. 3. Use four (4) Nº 6 x 3 ⁄ 8 “ screws supplied to secure the terminal board to the rough-in frame.
5 Refer to Figure 4. If a Nu T one Volume Control is installed in the system, connect the control’s IW-2 wiring to the ORN and ORN/WHT screw terminals at the master station. Only ONE NuTone speaker may be connected to each volume control. Each volume control/speaker counts as a remote station.
Model IA-29 Only 1. Refer to Figure 8. Locate the chime selector switch mounting bracket in the master unit. 2. Remove and set aside the chime selector switch retaining screw located in the master unit. 3. Remove and discard the square foam pads on the chime selector switch PC board connected to the chime module.
7 CONNECTING THE POWER TRANSFORMERS 1. Refer to Figure 14. The transformers’ primary leads should already be connected to the 120 volt AC house supply wiring. Be sure power is off before connecting transformers to master unit. 2. Locate the two (2) sets of red/wht transformer leads on the lower left corner of the master unit.
8 INST ALLA TION (Continued) FIGURE 16 FIGURE 17 CONNECTING THE MASTER ST A TION TO THE TERMINAL BOARD 1. Refer to Figures 16 and 17. Plug all five connectors into the terminal board. 1 . • Insert black ribbon cable with 10 pin plug into CN104 connector.
CONNECTING THE RADIO ANTENNA 1. Refer to Figure 18. Plug radio antenna (supplied with IR105 rough-in frame) into the 2-pin connector located on the main circuit board. Be certain the tab on the connector is facing towards the top of the master unit, as illustrated.
10 CONNECTING OPTIONAL ACCESSORIES 1. Refer to Figure 22. To connect an external audio source (NuTone Model CP-95 cassette, stereo system, VCR, TV, etc. with low level audio output) to the IMA-4406 master station, locate the TAPE and AUX iliary inputs on the upper center of the master station’s main circuit board.
11 clearance hole must be drilled behind the mounting bracket before securing the master station panel. POWERING UP THE SYSTEM Once all connections have been completed throughout the system, it is time to apply power to the master station.
12 OPERA TIONAL CHECKOUT SCAN: Activates scan tuning during AM/FM operation. st UP/DOWN TUNING: Provides manual tuning of the AM/FM radio. MEMORY 1-6 KEYS: Provides direct access to stored radio frequencies. TRACK : Returns to the beginning of the current track and/or previous tracks.
13 CAUTION Never touch the lens of the CD player or damage will result! DIGIT AL CLOCK SETTING THE TIME The proper clock setting procedure is arranged in 4 segments. Each segment must be completed in 5 seconds. Follow the procedure below. 1. Press the TIME SET key one time.
14 SETTING PROGRAM AUDIO CONTROLS (CONTINUED) 7. Adjust the MASTER VOLUME control and all remote station’s volume controls to the volume level you desire. In order to have proper intercom audio levels, it is r ecommended that the M ASTER VOLUME a nd remote stations’ VOLUME controls be set at 2 ⁄ 3 volume or higher.
15 KEY DISPLAY KEY DISPLAY No key 1:00 Memory 2 1:14 Scan 1:01 Memory 3 1:15 s 1:02 Memory 4 1:16 t 1:03 Memory 5 1:17 Program Off 1:04 Memory 6 1:18 AM 1:05 Play/Pause 1:19 FM 1:06 RDM/RPT 1:20 Tape .
16 TROUBLE No radio, no intercom. ( No Display). N o radio, intercom working. (AM/FM indicator on.) Low or distorted radio volume. Weak and distorted music, chime and intercom audio. No electrical power. Defective transformer. F aulty Master Station. I nstallation problem.
Optional Electronic Chime (Models IA-28 or IA-29) does not operate or operates at a low level. Improper volume setting. TROUBLE Hum in speakers. Remote Station not working. No door communication. Intercom wiring run too close to household AC power wiring.
18 When CD playback is started, it stops immediately or stops during playback. Disc is badly scratched or warped. Replace the disc. Install CD with label facing outward. Disc is loaded with label facing inward. Replace with conventional music format CD.
19.
4820 Red Bank Road, Cincinnati, Ohio 45227 Printed in China, Rev. 06/06, Part No. 62377 P roduct specifications subject to change without notice..
デバイスNuTone IMA4406の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
NuTone IMA4406をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNuTone IMA4406の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。NuTone IMA4406の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。NuTone IMA4406で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
NuTone IMA4406を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNuTone IMA4406の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、NuTone IMA4406に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNuTone IMA4406デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。