OKIメーカーLE810DTの使用説明書/サービス説明書
ページ先へ移動 of 53
User’s Guide 59320201 my.okidata.com RT322 LE810DT.
Copyright Information Copyright © 2010 by Oki Da ta. Al l Rights Reserved Document Information LE810DT User’s Guide P/N 59320201 Revision 1.2 April, 2010 Disclaimer Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date.
Contents _________________________ LE810DT User’s Guide 3 Introduction . . . . . . . . . . . . . . . . . . . . . . 4 About This Manual . . . . . . . . . . . . . . . . . . . 4 General Printer Description . . . . . . . . . . . . . 5 Printer Components .
LE810DT User’s Guide 4 Introduction Introduction About This Manual This manual uses special in formation boxes. Examples of these boxes and the type of information provided in each, are below. Warning! Provides information th at, if unheeded, may result in pers onal injury.
LE810DT User’s Guide 5 Introduction General Printer Description The LE810DT printer comes in several config urations which can differ by • Connection ports on th e back of the printer • Default .
LE810DT User’s Guide 6 Introduction Printer Components 1 Operator P anel 2 Print Assembly 3 Platen R oller 4 Dispenser Latch 5 Print Head Latch 6 R ewinder Shaft (only pr esent on some models) 7 Ext.
LE810DT User’s Guide 7 Introduction Operator Panel 1 LCD Displa y 2 Status LED - Illuminates green when online and turns off when offline. - Blinks green when receiving data or the buffer is near full. - Illuminates or blinks red wh en detecting a printer error .
LE810DT User’s Guide 8 Installation Installation Parts Identification 1 CD-ROM 2 Po we r C a b l e 3 USB Cable (included only on mode ls equi pped with a USB port) 4 Printer (front view) Printer Installation Site Location • Place the printer on a so lid flat surface, a wa y from hazardous materials.
LE810DT User’s Guide 9 Installation Interface Connection USB / RS232C / IEEE Models 1. Locate the interface connection ports on the back of the printer . 1: USB 2: Serial (RS-232C) 3: IEEE Parallel 2. Connect the appropriate cable to the in terf ace port, then connect it to the computer .
LE810DT User’s Guide 10 Installation Ethernet (LAN) Models 1. Locate the Ethernet port on the back of the printer . 2. Plug a 10/100Base T Category 5 Ethernet cable (not supplied) into the Ethernet port on the printer and then into the computer . USB Only Model 1.
LE810DT User’s Guide 11 Installation Connect to Power 1. Connect the power cable to the power socket on the ba ck of the printer , then connect it to a 120-volt, grounded power outlet. 2. T urn the printer on. 3. Set the interface option in the configur ation menus of the oper ator panel.
LE810DT User’s Guide 12 Installation Media Selection Both roll-type and fanfold media c an be used with the printe r. To use fanfol d media, you may need to re move the acce ss plate on the back of the prin ter as described under Loading Media, Fanfold Type.
LE810DT User’s Guide 13 Loading Media Roll-Type, with Liner Fed to Rewinder Shaft With roll-type media loaded this way, the liner (1) autom atically separate s from the media and is pulled back in to the printer and wrapped around the rewinder shaft (2).
LE810DT User’s Guide 14 2. Open the printer front d oor: push down on the green dispen ser latch (1 ) to release the door , then swing it open (2). 3.
LE810DT User’s Guide 15 4. Pull the green Media Supply Guide (1) out as far as it will go , then angle the label roll over it and push the roll back against the printer housi ng. Push the Media Support Guide back in until it fits sn ugly against the media roll (2).
LE810DT User’s Guide 16 6. Push in on the bottom of the Outside Media Guide (1) to move the top out of the way while y ou are lo ading the media. 7. Slide the media into the print path, making su re it goes under the Media Hold-Down (1) and under the Sensor Assembly (2) Push it against the back of the printer .
LE810DT User’s Guide 17 8. Adjust the media sensor to compensate for irregulari ties in the media (i.e.: notch, tag hole, gap, perforation or ma rkings).
LE810DT User’s Guide 18 10.Pull the media roll out unt il about 24 inches are exposed, then remov e the labels from that section. Fe ed the end of the line r back into the bottom of th e printer , under the Backing Dr ive R oller (1). 11.Pull out the green tab (1) on the front of the T ake-Up Spindle (2).
LE810DT User’s Guide 19 12.Swing the Head Latch back down to close the print head, then latch it in place. 13.Close the front door and lower the top access cover into place. Attention! These covers have interloc k switches and the printer will not operate if either is open.
LE810DT User’s Guide 20 Roll-Type, Front Exit with Liner Attached 1. Lift up the T op Access Cover ..
LE810DT User’s Guide 21 2. Open the printer front d oor: push down on the green dispen ser latch (1 ) to release the door , then swing it open (2). 3.
LE810DT User’s Guide 22 4. Pull the green Media Supply Guide (1) out as far as it will go , then angle the label roll over it and push the roll back against the printer housi ng. Push the Media Support Guide back in until it fits sn ugly against the media roll (2).
LE810DT User’s Guide 23 6. Push in on the bottom of the Outside Media Guide (1) to move the top out of the way while y ou are lo ading the media. 7. Slide the media into the print path, making su re it goes under the Media Hold-Down (1) and under the Sensor Assembly (2) Push it against the back of the printer .
LE810DT User’s Guide 24 8. Adjust the media sensor to compensate for irregulari ties in the media (i.e.: notch, tag hole, gap, perforation or ma rkings).
LE810DT User’s Guide 25 10.Swing the Head Latch back down to close the print head, then latch it in place. 11.Close the front door and lower th e top a ccess cover into place. Attention! These covers have interloc k switches and the printer will not operate if either is open.
LE810DT User’s Guide 26 Fanfold Type 1. Lift up the T op Access Cover ..
LE810DT User’s Guide 27 If the back plate is on your pr inter, perform the following step ; other wise, s kip to step 3. 2. R emov e the back plate co v ering the access hole. a. Press on the pin holders (1) inside th e printer at either end of the br acket until the pins extend from the outer housing.
LE810DT User’s Guide 28 3. Place the stack of fanfold media behind the printer and feed the first label in through the opening. 4. Locate the metal Outside Media Guide (1) under the print path and slide it toward you as far as it will go .
LE810DT User’s Guide 29 5. Push in on the bottom of the Outside Media Guide (1) to move the top out of the way while y ou are lo ading the media. 6. Slide the media into the print path, making su re it goes under the Media Hold-Down (1) and under the Sensor Assembly (2) Push it against the back of the printer .
LE810DT User’s Guide 30 7. Adjust the media sensor to compensate for irregulari ties in the media (i.e.: notch, tag hole, gap, perforation or ma rkings).
LE810DT User’s Guide 31 9. Swing the Head Latch back down to close the print head, then latch it in place. 10.Close the front door and lower th e top a ccess cover into place. Attention! These covers have interloc k switches and the printer will not operate if either is open.
LE810DT User’s Guide 32 Operational Mode Selection There are three modes of printer operation; T ear -off , Continuous, and Dispense. Tear-off Mode • F or printing labels one at a time. • The liner remains with the la bel as it exits the printer .
LE810DT User’s Guide 33 Printer Configuration Printer Configuration Basic Configuration Modes Configuratio n is done using the ope rator panel buttons.
LE810DT User’s Guide 34 Printer Configuration Advanced Mode For making basic printer oper ational adjustments. Typica lly, once these adjustment settings have been made, they will not require additional ch anges unless a ne w job is downloaded.
LE810DT User’s Guide 35 Printer Configuration Counters Mode • Print Head Counter The head counter records th e length of the media that has been printed since the print head was installed. It should be reset each time the print head is replaced. •L i f e C o u n t e r .
LE810DT User’s Guide 36 Printer Configuration Test Print Mode For printing a test label. Test labels are designed to identify failu res in configuration, adjustments problems, and mechanical defects.
LE810DT User’s Guide 37 Printer Configuration Default Setting Mode For resetting the printer to the default co nfiguration state as received from the factory. Use the printer’s buttons to select and en ter the required options. Power printer off and th en on again to ex i t.
LE810DT User’s Guide 38 Printer Configuration Hex Dump Mode The contents of the print b uffer and the contents r eceived before it may be examined through the use of the Hex Dump Mode.
LE810DT User’s Guide 39 Printer Configuration Menu Definition Tables Normal Mode Display Description ONLINE QT Y XXXXXX Displays the printer’ s operational status. The ONLINE status is displayed on the top line and the label quantity status is on the bottom.
LE810DT User’s Guide 40 Printer Configuration Advanced Mode Display Description AD V ANCED MODE Is the first menu screen of the Advanced Mode. The Advanced Mode is provided to make basic printer op erational adjustments.
LE810DT User’s Guide 41 Printer Configuration Counters Mode Display Description AD V ANCED MODE First transitional menu screen to access the Counters Mode. SER VICE MODE Second transitional menu screen to acces s the Counters Mode. COUNTERS MODE Is the first menu screen of the Counters Mode.
LE810DT User’s Guide 42 Printer Configuration Test Print Mode Display Description TEST PRINT MODE CONFIGURAT ION BARCODE HEADCH EC K FACTORY Is the initial screen of the T est Print Mode. • CONFIGURATION: The printer’s configuration settings. • BARCODE: The printer’s installed barcodes.
LE810DT User’s Guide 43 Printer Configuration Default Setting Mode Hex Dump Mode Display Description DEFAULT SETTING Y ES N O Is the first menu screen of the printer’s Default Setting Mode. The Default Setting Mode allows the printer to be reset to the programmed condition as received from the factory .
LE810DT User’s Guide 44 Troubleshooting Troubleshooting Test Label Printing The test label is designed to assist in the identification of prin t problems. The actual content of the test label depends on the type of test label printed. To print a test label: 1.
LE810DT User’s Guide 45 Troubleshooting Sample Test Print Label 1C o m p a r e t h i s s c a l e o n e a ch side to ensure the print is evenly spaced horizontally . 2 Visually inspect these rows for vo ids indicating defective elements. 3 Line sharpness is determined by print speed and dar kness.
LE810DT User’s Guide 46 Maintenance Maintenance Cleaning the Printer Cleaning of the printer is a necessary maintenance activi ty to ensure print quality and longer printer life. Ther e are two basic types of clea ning involved; the removal of loose debris and th e removal of residue.
LE810DT User’s Guide 47 Maintenance Cleaning the Print Head and Platen 1. T urn the printer off an d remove the power cable. 2. Open the T op Access Cover .
LE810DT User’s Guide 48 Maintenance 3. R otate the green Head Latch counte r clockw ise to open the print head. 4. R emov e an y print media from the print head.
LE810DT User’s Guide 49 Specifications Specifications Physical Characteristics Power Environmental Processing Width 10.7 Inches (2 71 mm) Height 12.7 Inches (3 22 mm) Depth 16.
LE810DT User’s Guide 50 Specifications Interfaces Print Specifications Sensing Specifications Model Interface(s) LE810DT - SER/PAR/USB Combo Interface Board: • Serial: RS232C (9600 to 57,600 bps ).
LE810DT User’s Guide 51 Specifications Media Commands Width • Media Width: 0.866 to 5.04 Inches (22-128 mm) • Media Width with Backing P aper : 0.984 to 5.16 Inches (25- 131 mm) Length • Media Length: 15.63 Inches (397 mm) • Media Length with Backing P aper: 15.
LE810DT User’s Guide 52 Specifications Character Font Capabilities TTF fonts 0 15 dots H x 12 dots W Bitmap fonts A 9 dots H x 5 dots W B 11 dots H x 17 dots W C 18 dots H x 10 dots W D 18 dots H x .
LE810DT User’s Guide 53 Specifications Bar Code Capabilities Bar Code Capabilities Linear Bar Codes • UPC A/E • JAN 8/13 •E A N 8 / 1 3 • Code 39 • Code 93 • Code 128 • Interleaved 2 o.
デバイスOKI LE810DTの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
OKI LE810DTをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOKI LE810DTの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。OKI LE810DTの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。OKI LE810DTで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
OKI LE810DTを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOKI LE810DTの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、OKI LE810DTに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOKI LE810DTデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
