OlympusメーカーMAUSB-10の使用説明書/サービス説明書
ページ先へ移動 of 52
USB Reader/Writer REFERENCE MANU AL.
2 Introduction Thank you for purchasing our product. This product is exclusively for reading and writing data to an xD-Picture Card/SmartMedia. Y ou can transfer large amounts of data to and from the card quickly and easily using a computer equipped with a USB port (IBM PC/A T compatibles and Macintosh).
3 Contents Introduction .................................................................................................................................... 2 Contents ...................................................................................
4 What’ s inc luded Make sure all the following items are included. If any items are missing, inform the shop from where you purchased this product right away .
5 Before getting started System requirements Y our computer must conform to the following minimum standards in order to use it with the MAUSB-10. ● Compatible operating systems IBM PC/A T compatible.
6 W indows Macintosh [USB 1.1 compatible] T urn on computer . Place provided Installation CD-ROM in CD-ROM drive. *2 Install driver . *2 Restar t computer . *2 Connect to computer . Get started! *4 *1 : Windows 95/3.1/NT are not compatible. *2 : Y ou only need to perform this procedure before using the MAUSB-10 for the first time.
7 How to install Also refer to your computer ’s user manual and the manuals for any optional devices you are using. 1 T ur n on the computer <98/98 SE/Me ⽧ Install> T urn on your computer’s power (and connected devices) to start Windows.
8 <98/98 SE/Me ⽧ Install> 4. During installation, the window at right appears. * The installation time may vary , depending on your computer. 5. When the driver installation is complete, the window at right appears. Click the “Finish” button.
9 1. Double-click “My Computer”. <98/98 SE/Me ⽧ Install> 2. Right-c lic k “OL YMPUS”. Select “Open” from the pop-up menu. 4. Double-click “SETUP”. * The “OL YMPUS USB Reader/Writer InstallShield Wizard” window appears. Start installing by following “Install the device driver” ( 墌 p.
10 Operating the MAUSB-10 The operating procedures for the MAUSB-10 under Windows are described below . 1 Connecting to the computer <98/98 SE/Me ⽧ Operation> After installing the device driver , connect the MAUSB-10’ s connector to the USB port on your computer .
11 < 98/98 SE/Me ⽧ Operation > When the MAUSB-10 is connected to your computer , it is recognized as a “Removable Disk”. Y ou can see two “Removable Disk” icons by opening “My Computer” from the desktop.
12 2 Inserting a card <98/98 SE/Me ⽧ Operation> 1. Make sure the MAUSB-10 is connected to the computer and insert the card into the corresponding card slot. [xD-Picture Card] Make sure the card is level and that the gold-colored contact area is facing down .
13 3 Removing a card <98/98 SE/Me ⽧ Operation> Close all software programs that are using data on the card (e.g. Explorer , graphics applications), then follow the steps below . Attention! If you do not follow the steps below , the data on the card(s) may be damaged.
14 4 Copying files from a card <98/98 SE/Me ⽧ Operation> 4. Drag the file icons you want to copy and drop them onto the destination folder . * The process is the same as copying files from a floppy disk. * It is also possible to move files to another folder, erase files, or write data from another folder .
15 5 Formatting a card <98/98 SE/Me ⽧ Operation> 6 Disconnecting the MAUSB-10 <98/98 SE/Me ⽧ Operation> Close all software programs that are using the card (e. g. Explorer , graphics applications), then follow the steps below . 1. Make sure that the status lamp is NOT on.
16 How to uninstall the device driver <98/98 SE/Me> The device driver can be deleted if it is no longer needed. First make sure that the MAUSB-10 is disconnected from the computer’ s USB port, then follow the steps below . * On-screen displays or messages may vary depending on the version of Windows you are using.
17 How to uninstall the device driver (Cont.) <98/98 SE/Me> 4. A confirmation window appears. Click “OK”. 5. The “InstallShield Wizard” window appears. 6. The window at right appears. Click the “Finish” button. 7. The window at right appears.
18 How to install Also refer to your computer ’s user manual and the manuals for any optional devices you are using. 1 T ur n on the computer <2000/XP ⽧ Install> T urn on your computer’s power (and connected devices) to start Windows 2000/XP .
19 <2000/XP ⽧ Install> 4. During installation, the window at right appears. * The installation time may vary , depending on your computer. 5. When installation of the device driver is complete, the window at right appears. Click the “Finish” button.
20 1. Double-click “My Computer”. <2000/XP ⽧ Install> 2. Right-c lic k “OL YMPUS”. Select “Open” from the pop-up menu. 4. Double-click “SETUP”. * The “OL YMPUS USB Reader/Writer InstallShield Wizard” window appears. Start installing by following “Install the device driver” ( 墌 p.
21 Operating the MAUSB-10 The operating procedures for the MAUSB-10 under Windows 2000/XP are described below . 1 Connecting to the computer <2000/XP ⽧ Operation> After installing the device driver , connect the MAUSB-10’ s connector to the USB port on your computer .
22 <2000/XP ⽧ Operation> [Installing the hardware] 1. The “Found New Hardware Wizard” window appears when the MAUSB-10 is connected to Windows XP for the first time. Make sure that “Install the software automatically [Recommended]” is selected and click the “Next” button.
23 <2000/XP ⽧ Operation> 5. When the driver installation is complete, the window at right appears. Click the “Finish” button. 6. Confirm that two “Removable Disk” icons have been added by opening “My Computer” from the desktop. * The drive letters (e.
24 Before connecting After connecting MAUSB-10 * In this example, the Removable Disks are recognized as the J and K drive. The drive letters (e.g. “J:”, “K:”, etc.) used by your computer may dif fer depending on your computer and/or connected optional devices.
25 2 Inserting a card <2000/XP ⽧ Operation> 1. Make sure the MAUSB-10 is connected to the computer and insert the card into the corresponding card slot. [xD-Picture Card] Make sure the card is level and that the gold-colored contact area is facing down .
26 3 Removing a card <2000/XP ⽧ Operation> Close all software programs that are using data on the card (e.g. Explorer , graphics applications), then follow the steps below . Attention! If you do not follow the steps below , the data on the card(s) may be damaged.
27 4 Copying files from a card <2000/XP ⽧ Operation> 1. Start up your computer . 2. Double-click “My Computer” from the desktop. 3. T o view the contents of a card, double-clic k the corresponding “Removable Disk” icon.
28 5 Formatting a card <2000/XP ⽧ Operation> [Before formatting the card] • T o format a card, log on with the user name “Administrator”, or use a user name with administrator privileges. Otherwise, formatting the card will be impossible.
29 6 Disconnecting the MAUSB-10 <2000/XP ⽧ Operation> Close all software programs that are using data on the card (e.g. Explorer , graphics applications), then follow the steps below . 1. Make sure that the status lamp is NOT on. 2. Left-click the “Unplug or Eject Hardware” icon on the taskbar .
30 How to uninstall the device driver <2000/XP> The device driver can be deleted if it is no longer needed. First make sure that the MAUSB-10 is disconnected from the computer’ s USB port, then follow the steps below . * On-screen displays or messages may vary depending on the version of Windows you are using.
31 How to uninstall the device driver (Cont.) <2000/XP> 4. A confirmation window appears. Click “OK”. 5. The “InstallShield Wizard” window appears. The device driver is no longer installed. 6. The window at right appears. Click the “Finish” button.
32 How to install Also refer to your computer ’s user manual and the manuals for any optional devices you are using. 1 T ur n on the computer <Mac OS 8.6~9.2 ⽧ Install> T urn on your computer’s power (and connected devices) to start Mac OS.
33 3 Install the device driver <Mac OS 8.6~9.2 ⽧ Install> When using the MAUSB-10 for the first time, you must first install the device driver included on the provided CD-ROM. 3. Doub le-click the “Mac OS 9” folder . 4. Doub le-click “USB Reader_Writer”.
34 < Mac OS 8.6~9.2 ⽧ Install > 6. Click the “Restart” button. The device driver is now installed. (Remove the CD-ROM from the CD-ROM drive and store it in a safe place.) 5. When the Mac OS 8.x, 9.x installer starts up, the window at right appears.
35 Operating the MAUSB-10 The operating procedure for the MAUSB-10 under Mac OS is described below . 1 Connecting to the computer <Mac OS 8.6~9.2 ⽧ Operation> After installing the device driver , connect the MAUSB-10’ s connector to the USB port on your computer .
36 2 Inserting a card <Mac OS 8.6~9.2 ⽧ Operation> 1. Make sure the MAUSB-10 is connected to the computer and insert the card into the corresponding card slot. [xD-Picture Card] Make sure the card is level and that the gold-colored contact area is facing down .
37 3 Removing a card <Mac OS 8.6~9.2 ⽧ Operation> Close all software programs that are using data on the card (e. g. graphics applications), then follow the steps below . Attention! If you do not follow the steps below , the data on the card(s) may be damaged.
38 4 Copying files from a card <Mac OS 8.6~9.2 ⽧ Operation> 1. Insert a card in the MAUSB-10. * The status lamp blinks, then the card icon appears on the desktop. * The icon’s appearance may vary , depending on the card and the OS version. 2.
39 How to uninstall the device driver <Mac OS 8.6~9.2> The device driver can be deleted if it is no longer needed. First make sure that the MAUSB-10 is disconnected from the computer’s USB port, then follow the steps below . 1. From the desktop, double-click the hard disk icon.
40 How to install Also refer to your computer ’s user manual and the manuals for any optional devices you are using. 1 T ur n on the computer <Mac OS X ⽧ Install> T urn on your computer’s power (and connected devices) to start Mac OS.
41 3 Install the device driver <Mac OS X ⽧ Install> When using the MAUSB-10 for the first time, you must first install the device driver included on the provided CD-ROM. 1. Doub le-click the “OL YMPUS” icon. 2. Doub le-click the “MAUSB-10” folder .
42 < Mac OS X ⽧ Install > 6. Enter the administrator ’ s name and the pass- word, then click the “OK” button. 7. Click the “Continue” button. 8. Click the “Continue” button. 9. Select the disk to install on, then click the “Continue” button.
43 < Mac OS X ⽧ Install > 10. Click the “Install” (or “Upgrade”) button. 11. Click the “Continue Installation” button. 12. The window at right appears during the installation. 13. Click the “Restart” button. The device driver is now installed.
44 Operating the MAUSB-10 The operating procedure for the MAUSB-10 under Mac OS is described below . 1 Connecting to the computer <Mac OS X ⽧ Operation> After installing the device driver , connect the MAUSB-10’ s connector to the USB port on your computer .
45 2 Inserting a card <Mac OS X ⽧ Operation> 1. Make sure the MAUSB-10 is connected to the computer and insert the card into the corresponding card slot. [xD-Picture Card] Make sure the card is level and that the gold-colored contact area is facing down .
46 3 Removing a card <Mac OS X ⽧ Operation> Close all software programs that are using data on the card (e. g. graphics applications), then follow the steps below . Attention! If you do not follow the steps below , the data on the card(s) may be damaged.
47 4 Copying files from a card <Mac OS X ⽧ Operation> 1. Insert a card in the MAUSB-10. * The status lamp blinks, then the card icon appears on the desktop. * The icon’ s appearance may vary , depending on the card and the OS version. 2. Double-click the icon to display the files that you want to copy .
48 T roubleshooting Windows The status lamp (green) does not light. A “Found New Hardware Wizard” windo w appears when you connect the MAUSB-10. The MAUSB-10 doesn’t work even after installing the driver and connecting the MAUSB-10 to the computer .
49 T roubleshooting Macintosh The status lamp (green) does not light. No card icon(s) appears on the computer’ s screen. Y ou can read a card, but not write to it. Y ou cannot write with a SmartMedia. The error message “File Sharing is invalid.” appears.
50 Specifications * The specifications in this manual are subject to change without prior notice. * For the latest information, visit the OL YMPUS web site (http://www .olympus.com). * 1 Some cards with ID are not generally available for purchase. Consult your nearest SmartMedia dealer for details.
51 Glossary of T er ms A program used to operate or manage a peripheral device (printer , modem, digital camera, USB reader/writer , etc.). Without the proper driver installed, a peripheral device will not be recognized by the computer . A window that appears on the monitor when the computer requires user confirmation or instructions on what to do.
OL YMPUS OPTICAL CO ., L TD. VT398703.
デバイスOlympus MAUSB-10の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Olympus MAUSB-10をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOlympus MAUSB-10の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Olympus MAUSB-10の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Olympus MAUSB-10で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Olympus MAUSB-10を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOlympus MAUSB-10の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Olympus MAUSB-10に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOlympus MAUSB-10デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。