Omegaメーカー8000の使用説明書/サービス説明書
ページ先へ移動 of 24
METAL DETECTOR 8000 O WNER’S MANUAL If you do not have prior experience with a metal detector , we strongly recommend that you: 1) Adjust the Sensitivity to a low setting in the event of false signals. Always begin use at a reduced sensitivity level; increase sensitivity only after you have become familiar with the detector .
2 T ABLE OF CONTENTS T erminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5 Batteries . . . . . . . . . .
TERMINOLOG Y The following terms are used throughout the manual, and are standard terminology among detectorists. ELIMINA TION Reference to a metal being "eliminated" means that the detector will not emit a tone, nor light up an indicator , when a specified object passes through the coil’s detection field.
21 4 ASSEMBL Y Assembly is easy and requires no tools. ● 1 Loosen both Locking Collars by rotating 100% counterclockwise ● 2 Insert the Upper Stem into the S-Rod and click Silver Button into hole ● 3 Position the lower stem with the silver button toward the back.
ASSEMBL Y Adjusting the Arm Rest The arm rest may be moved forward or backwards by removing the single screw and nut, and then repositioning the 2-piece arm rest. Users with shorter arms may find the arm rest more comfortable in the forward position. In order to move the arm rest backwards, the plastic plug must be removed from the aluminum tube.
6 A 4-segment battery indicator at the top-left of the display indicates the battery condition. The detector requires a single 9-volt ALKALINE battery (battery not included). Do not use ordinary zinc carbon batteries. Do not use “Heavy Duty” batteries.
AUDIO T ARGET IDENTIFICA TION S YSTEM Different types of metals will induce dif ferent types of sounds, depending on your TONES setting. There are 4 choices in DISCRIMINA TION MODE : The default setting is d3. T o choose from the above selections, press the T ONES touch pad.
8 VIII. Rotate the DISC knob until the words IRON, FOIL, NICKEL, P-T AB, S-CAP and ZINC all disappear . IX. W ave the nickel a. The nickel will not be detected. X. Press the NOTCH touchpad on the front panel three times. The word “NICKEL” will start flashing.
9 THE BASICS OF MET AL DETEC TING A hobby metal detector is intended for locating buried metal objects. When searching for metals, underground or on the surface, you have the following challenges and objectives: 1. Ignoring signals caused by ground minerals.
10 4. Size and Depth of Buried Objects When using the detector in the motion DISCRIMINA TION mode, the relative depth of an object is displayed in the center of the display with the SIGNAL strength indicator . A more accurate depth reading is available in a no- motion mode, using PINPOINT .
11 OPERA TION and CONTROLS GROUND GRAB Press-and-hold touch pad in middle to activate automatic ground balancing Press or to manually adjust the ground setting PINPOINT Press-and-hold to narrow down location of your finds NOTCH Press to selectively include or exclude specific target categories.
13 CONTROL P ANEL cont. CONTROL P ANEL CONTROL KNOBS ARE AS FOLLOWS: 1. SENSITIVITY : a. Click right to turn on. Click left to turn off. b. T urning the knob clockwise increases the detector ’s sensitivity; the higher the sensitivity , the deeper targets will be detected, and the more likely the detector will be to detect very small targets.
13 CONTROL P ANEL cont. CONTROL P ANEL CONTROL KNOBS ARE AS FOLLOWS: 1. SENSITIVITY : a. Click right to turn on. Click left to turn off. b. T urning the knob clockwise increases the detector ’s sensitivity; the higher the sensitivity , the deeper targets will be detected, and the more likely the detector will be to detect very small targets.
11 OPERA TION and CONTROLS GROUND GRAB Press-and-hold touch pad in middle to activate automatic ground balancing Press or to manually adjust the ground setting PINPOINT Press-and-hold to narrow down location of your finds NOTCH Press to selectively include or exclude specific target categories.
10 4. Size and Depth of Buried Objects When using the detector in the motion DISCRIMINA TION mode, the relative depth of an object is displayed in the center of the display with the SIGNAL strength indicator . A more accurate depth reading is available in a no- motion mode, using PINPOINT .
9 THE BASICS OF MET AL DETEC TING A hobby metal detector is intended for locating buried metal objects. When searching for metals, underground or on the surface, you have the following challenges and objectives: 1. Ignoring signals caused by ground minerals.
8 VIII. Rotate the DISC knob until the words IRON, FOIL, NICKEL, P-T AB, S-CAP and ZINC all disappear . IX. W ave the nickel a. The nickel will not be detected. X. Press the NOTCH touchpad on the front panel three times. The word “NICKEL” will start flashing.
AUDIO T ARGET IDENTIFICA TION S YSTEM Different types of metals will induce dif ferent types of sounds, depending on your TONES setting. There are 4 choices in DISCRIMINA TION MODE : The default setting is d3. T o choose from the above selections, press the T ONES touch pad.
6 A 4-segment battery indicator at the top-left of the display indicates the battery condition. The detector requires a single 9-volt ALKALINE battery (battery not included). Do not use ordinary zinc carbon batteries. Do not use “Heavy Duty” batteries.
ASSEMBL Y Adjusting the Arm Rest The arm rest may be moved forward or backwards by removing the single screw and nut, and then repositioning the 2-piece arm rest. Users with shorter arms may find the arm rest more comfortable in the forward position. In order to move the arm rest backwards, the plastic plug must be removed from the aluminum tube.
21 4 ASSEMBL Y Assembly is easy and requires no tools. ● 1 Loosen both Locking Collars by rotating 100% counterclockwise ● 2 Insert the Upper Stem into the S-Rod and click Silver Button into hole ● 3 Position the lower stem with the silver button toward the back.
TERMINOLOG Y The following terms are used throughout the manual, and are standard terminology among detectorists. ELIMINA TION Reference to a metal being "eliminated" means that the detector will not emit a tone, nor light up an indicator , when a specified object passes through the coil’s detection field.
2 T ABLE OF CONTENTS T erminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5 Batteries . . . . . . . . . .
5- YEAR LIMITED W ARRANT Y The Omega metal detector is warranted against defects in materials and workmanship under normal use for five years from the date of purchase to the original owner . Damage due to neglect, accidental damage, or misuse of this product is not cov- ered under this warranty .
デバイスOmega 8000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Omega 8000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOmega 8000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Omega 8000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Omega 8000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Omega 8000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOmega 8000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Omega 8000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOmega 8000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。