Oneida Air Systemsメーカー10 HPの使用説明書/サービス説明書
ページ先へ移動 of 24
10 HP NYB Pulley/Belt Drive Cyclonic Dust Collectors Oneida Air Systems, Inc. 1001 West Fayette S t., Syracuse, N.Y . 13204 Phone 1-800-732-4065 315-476-5151 Fax 315-476-5044 www .
Thank Y ou for Choosing an Oneida Air Systems Product! OAS manufactures and sells dust collection equipment only . Our qualified technicians and sales staf f are available 7:30am - 6:00pm EST Mon. - Thur . and 7:30am - 5:00pm EST Fri. to answer any questions concerning OAS products and dust collection.
O.A.S. 2007 c 10 HP Pulley Drive Owner s Manual I. System Star t-Up Information 1. Read the installation and maintenance instructions as well as the recommended safety practices in this manual. 2. Install Ductwork completely: A.) Seal ductwork with silicone sealant or duct tape.
II. 10hp Pulley Drive Configurations 1. No Filter - V ent Outside - Caution: If exhaust air is vented outside you must provide make up / return air . Flue gases (carbon monoxide) can be drawn into the shop from furnaces, water heaters or other appliances.
III. General Specifications & Fan Per formance Cur ves 4 10hp Fan Cur ves O.A.S. 2007 c 10 HP Industrial Systems Owner s Manual Full welded exterior Main body , cone and inlet: 16 ga. galv . Flanged 12 dia. Inlet; Flanged 13 dia. Outlet 80 high 14 rolled steel flange discharge 36 dia.
IV . Dimensions 5 O.A.S. 2007 c 10 HP Pulley Drive Owner s Manual T op V iew Dimensions - Largest Configuration 1 1/2 Flange w/ Bolt Holes 34 10hp - 229 14 10hp - 83 30 42 17 80 Approx. 18 36 14 39 36 8 39 32.
IV . Dimensions 6 O.A.S. 2007 c 10 HP Pulley Drive Owner s Manual - External Cartridge Filters 17 80 Approx. 18 36 10 14 14 39 10hp - 3 filters -Single Row - 66 36 29 1/8 8 39 62 12 55 Gal.
7 O.A.S. 2007 c 10HP Pulley Drive Owner s Manual C-3500 Cyclone Stand - Anchor Feet Securely to Floor to Prevent Tipping (4) 3/8-16 x 1 bolts for Cyclone mount (20) 3/8-16 x 1 bolts for Cross.
V . Configuration Examples Sleeve Kit - Sleeve-Kit 14 for C-2500 cyclone requires 16 - 18 for a single drum and 24 for 2x drums. Additional feet of flex can be purchased to make the sleeve kit longer if needed. Drum - S tandard 55 gal. steel drums are usually 35 - 36 high Oneida Air sells 55 gal.
VI. General Assembly Instructions 9 O.A.S. 2007 c 10 HP Pulley Drive Owner s Manual 1. Determine mounting height for the cyclone. - Height depends on size of Dust Bin and length of Flex Hose to Dust Bin connection. 2. Mount Angle Iron Brackets to wall using included hardware.
VI. General Assembly Instructions 10 O.A.S. 2007 c 10 HP Pulley Drive Owner s Manual 7. Set up Fan/Blower (Cont.) All moving part s must have guards to protect personnel. Safety requirement s vary , so the number and type of guards needed to meet company , local and OSHA standards must be determined and specified by the user .
5 gallon buckets 12 high (Not supplied with system). Can be purchased, Part No. SDS050000 or recycled joint compound bucket s or food storage containers can be used.
XII. Fan / Blower Wiring Diagram Wiring should always be done by a licensed electrician! 10 HP Pulley Drive Owner s Manual O.A.S. 2007 c Before Operation - Before making electrical power connections, check for proper grounding of motor and application.
IX . Fan / Blower - Maintenance The Fan / Blower has a TEFC - tot ally enclosed fan cooled motor that can be placed outside. The fan housing is adjustable by 22 1/2 degree increment s - outlet can be oriented by adjusting bolt hole locations between the scroll and the bracket assembly .
14 O.A.S. 2007 c 10 HP Pulley Drive Owner s Manual Maintenance of Fan / Blower (Cont.) 2.) Cleanliness - Keep both the interior and exterior of the motor free from dirt, water , oil and grease. 3.) Safety - Motors should be installed, protected and fused in accordance with latest issue of National Electrical Code, NEMA S tandard Publication No.
X . Accessories O.A.S. 2007 c 10 HP Pulley Drive Owner s Manual Dust Bin Options - (Must Order Custom Cyclone Mounting S tand.) 2. Hoppers - Large capacity hoppers from .
XII. Troubleshooting Motor Overheating The motor s internal circuit breaker will trip if the motor is overheating. Air leaks between the collector and dust bin - The lid of the dust bin and the cyclone must be in place and sealed when operating the dust collector .
XII. Fire Hazards - Read Before Installing and Operating 17 O.A.S. 2007 c 10 HP Pulley Drive Owner s Manual Do not use this product to collect other types of dust or flammable vapors. Fire or explosion may occur! Never collect sparks from a bench grinder into a wood dust collector .
XIII. T erms and Conditions Please look over the shipped order very carefully in the presence of the delivery person for damage or incomplete shipment before signing the delivery receipt. Please note any tears or irregularities in shipping packaging, however slight, on the shipping delivery receipt.
The External Filter can be cleaned using the following methods: W ait a few minutes for internal dust to settle then unclip and carefully empty dust bin. XIV . Directions for Cleaning External Filter Keep nozzle at least 6 from filter and keep your pressure down.
O.A.S. 2007 c 10 HP Pulley Drive Owner s Manual 20 XV . Filter Efficiency Gauge Mounting Instructions Can be attached up to 8 away . OR Air Flow to Filter Mounting Instructions 1. Mount brass static pressure tube in plenum with tip pointed into the air stream.
O.A.S. 2007 c 10 HP Pulley Drive Owner s Manual 21 P le as e se e comp l ete m an ufa ct u rer i ns t ruc t i o ns for mo re i nfo r m at i on. T h is supplement i s des i gn ed to aid Oneida A ir Systems cu stomers with frequentl y as k e d ques t ions.
O.A.S. 2007 c 10 HP Pulley Drive Owner s Manual 22 Open ac ces s cover on the over load, th en s e t t h eo v e r l o a da m p e r a g ed i a lt om a t c ht h eF L A amperage of your motor . Th e FLA v alue can be fo und o n y our mot or name pla te.
O.A.S. 2007 c 10 HP Pulley Drive Owner s Manual 23 L3 L2 L1 A1 21 13 T3 T2 T1 A2 22 14 M T3 T2 T1 96 L3 L2 L1 95 98 97 OL / SC T3 T2 T1 7 4 1 8 5 2 9 6 3 White Yel lo w Bro wn Pl ug - I n C onn ector Res et I nstall th is Ju mper fo r Sing le O Usi ng the Sa me Gaug e Wir e S i ze d & Co nnec te d t o L 1 & L2.
デバイスOneida Air Systems 10 HPの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Oneida Air Systems 10 HPをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOneida Air Systems 10 HPの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Oneida Air Systems 10 HPの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Oneida Air Systems 10 HPで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Oneida Air Systems 10 HPを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOneida Air Systems 10 HPの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Oneida Air Systems 10 HPに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOneida Air Systems 10 HPデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。