OnkyoメーカーTX-NR1007の使用説明書/サービス説明書
ページ先へ移動 of 156
E n A V Receiv er TX-NR1007 Instruction Manual Thank you for purchasing an Onkyo A V Receiv er. Please read this manual thoroughl y before making connections and plugg ing in the unit. Follo wing the inst ructions in this manual will enable you to obtain opti mum performance and listening enjoyment from your new A V Receiv er.
2 Impor tant Safety Instructions 1. Read these ins tructions. 2. Ke ep these instructi ons. 3. Heed all warnings. 4. Follo w all instructions. 5. Do not use this apparatus near w ater . 6. Clean only with dry cloth. 7. Do not block an y ventil ation openings.
3 Precautions 1. Recording Copyright —Unless it’ s for personal use only , recording copyright ed material is il legal wit h- out the permission of the copyright holder . 2. A C Fuse —The A C fuse inside the unit is not user- serviceable. If you cannot turn on the unit, contact your Onkyo dealer .
4 Precautions —Continued F or British models Replacement and mounting of an A C plug on the po wer supply cord of this unit should be performed only by qualified service personnel.
5 Contents Important Safety Instructions .......................................... 2 Precautions ................... ................................................. 3 Supplied Accessories ......................... ............................ 4 Features .
6 Features Amplifier • 135 W atts/Channel @ 8 ohms (FTC) • 180 W atts/Channel @ 6 ohms (IEC) • 230 W atts/Channel @ 6 ohms (JEIT A) • WRA T–Wide Range Amplif ier T echnology (5 Hz-100 kHz bandwidth) • Linear Opti mum Gain V olume Circuitry • 3-Step In verted Darlington Circuitry • H.
7 Features —Continued *6. HD Radio™ an d the HD Radi o Ready logo are propriet ary trademarks of iBiquity Di gital Corpor ation. T o recei ve HD Radio bro adcasts, you mu st install an Onkyo UP-HT1 HD Radio tun er module (sold separa tely). *7. In Europe, us ing banana p lugs to con nect speakers t o an audio amplifie r is prohibited.
8 Fr ont & Rear P anels The actual front panel has v arious logos printe d on it. They are not sho wn here for clarity . The page numbers in parentheses show where you can f ind the main explanation for each item. a ON/ST ANDBY button (43) This button is used to set the A V receiver to On or Standby .
9 Fr ont & Rear P anels —Continued (Nor th American models) (Eur opean and Asi an models) The page numbers in parentheses show where you can find the main explanation for each item. k PHONES jack (65) This 1/4-inch phone jack is for connecting a stan- dard pair of stereo hea dphones for priv ate listening.
10 Front & Rear P a nels —Continued w SETUP MIC jack (57) Audyssey MultEQ ® XT Room C orrection and Speaker Setup micropho ne connects here. x A UX INPUT (37) This input can be used to connect a camcorder, game console, and so on. There are jacks for com- posite video, anal og audio, and optical digital audio.
11 Fr ont & Rear P anels —Continued f T uning indi cators RDS (European models) (70): Lights when tuned to a radio station that supports RDS (Radio Data System). AU T O ( 6 8 ) : Lights when Auto T uning m ode is selected for AM or FM radio. Goes off when Manual T uning mode is selected.
12 Front & Rear P a nels —Continued d DIGIT AL CO AXIAL IN 1, 2, and 3 These coaxial digital audio inputs are for connect- ing components with coaxia l digital audio outputs, such as CD and D VD/BD players. The y’ re assign- able, which means you can assign each one to an input selector to suit your setup.
13 Fr ont & Rear P anels —Continued x MUL TI CH input: FR ONT L/R, CENTER, SUBWOOFER, SURR L/R, and SURR BA CK L/R This analog multichannel input is for connecting a component with a 5.1/7.1-channel analo g audio out- put, such as a D VD player , D VD- Audio or Super Audio CD-capable player , or an MPEG decoder .
14 Remote Contr oller Notes: • If the remote controller doesn’t w ork reliably , try replacing the batteries. • Don’ t mix new and old batteries or dif ferent types of batteries. • If you intend not to use th e remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.
15 Remote Controller —Contin ued For detailed information, se e the pages in parentheses. a ST ANDBY button (43) Sets the A V receiv er to Standb y . b ON button (43) T urns on the A V rece iv er. c A CTIVITIES b uttons (66, 146) Used with the MA CR O function.
16 Remote Contr oller —Continued ■ Controlling the tuner T o control the A V receiver’ s tuner, press the [TUNER] (or [RECEIVER]) button. Y ou can select AM or FM by pressing the [TUNER] b ut- ton repeatedly . 1 Arro w [ q ]/[ w ] b uttons Used to tune into radio stations.
17 About Home Theater Thanks to the A V receiver’ s superb capabilit ies, you can enjoy surround sound with a real sense of mov ement in your own home—just lik e being in a movie th eater or concert hall. W ith DVDs you can enjo y DTS and Dolby Digital.
18 Connecting the A V receiver Speaker Configurat ion For 9.2-channel surround-sound playback, you need nine speak ers and two po wered subwoofers. The following table i ndicates the channels you should use dependi ng on the number of speakers that you ha ve.
19 Connecting the A V receiver —Continued Using Dipole Speake rs Y ou can use dipole speakers for the surround left and right, surround back left a nd right speakers. Dipole speakers output the same sound in two directions. Dipole speakers typically ha ve an arro w printed on them to indicate how the y should be positioned.
20 Connecting the A V receiver —Contin ued Connecting the Speaker Cab les The follow ing illustration shows which spea k er should be connected to each pair of terminals. If you’ re using only one surround back speaker , connect it to the SURR B A CK/ZONE 3 L terminal.
21 Connecting the A V receiver —Continued The FR ONT L/R and SURR B A CK/ZONE 3 L/R termi- nal posts can be used with front speakers and surround back speakers respecti vely , or bi-amped to provide sepa- rate tweeter and woofer feeds for a pair of front speak ers that support bi-amping, pr oviding impro ved bass and treble performance.
22 Connecting the A V receiver —Contin ued This section explains ho w to connect the supplied indoor FM antenna and AM loop an tenna, and ho w to connect commercially av ailable ou tdoor FM and AM antennas. The A V receiv er won’t pick up any radio signals without any antenna connected, so you must co nnect the antenna to use the tuner .
23 Connecting the A V receiver —Continued Connecting an Outdoor FM Antenna If you cannot achie ve good re ception with the supplied indoor FM antenna, try a co mmercially a vailable out- door FM antenna instead. Notes: • Outdoor FM antennas w ork best outside, but usable results can someti mes be obtained when in stalled in an attic or l oft.
24 Connecting the A V receiver —Contin ued • Before making any A V connections, read the manuals supplied with your other A V components. • Don’t connect the po wer cord until you’ ve completed and double-checked a ll A V connections.
25 Connecting the A V receiver —Continued About HDMI Designed to meet the in crease d demands of digital TV , HDMI (High Definiti on Multimedia Interfa ce) is a new digita l interface standard for connecting TVs, projecto rs, D VD/BD players, set-top boxes, and other video co mponents.
26 Connecting the A V receiver —Contin ued Making HDMI Connections ■ Video Signals Digital video signals recei ved by th e HDMI IN jacks are norma lly output by the HDMI MAIN OUT and SUB OUT for display on your TV . Composite video, S-V ideo, and compone nt video sources can be upconv erted for the HDMI output.
27 Connecting the A V receiver —Continued By connecting both the audio a nd video outputs of your D VD/BD player and other A V components to the A V recei ver, you can select both the audio and video simultaneously simply by selecting th e appropriate input source on the A V receiv er.
28 Connecting the A V receiver —Contin ued ■ “Monitor Out” Setting Set to “Bot h ”, “Both (Main)” or “Both ( Sub)” W ith the “Monitor Out” sett ing set to “Both”, “Both (.
29 Connecting the A V receiver —Continued A udio Connection Forma ts Audio equipment can be connected to the A V receiv er by u sing any of the follo wing audio con- nection form ats: analog, optic al, coaxial, analog multichannel, or HDMI.
30 Connecting the A V receiver —Contin ued See “Connecting Components with HDMI” on page 25 for HDMI connection inf ormation. • W ith connection , you can listen to and record audio from your TV or listen in Zone 2 or Zone 3. • T o enjoy Dolby Digital and DTS, use connection or .
31 Connecting the A V receiver —Continued See “Connecting Compon ents with HDMI” on page 25 f or HDMI connection inf ormation. • W ith connection , you can listen to and record audi o from your D VD player or listen in Zone 2 or Zone 3. • T o enjoy Dolby Digital and DTS, use connection or .
32 Connecting the A V receiver —Contin ued Hooking Up the Multich annel Input If your D VD player supports multichannel audio formats such as D VD- Audio and Super Au dio CD, and it has a multi- channel analog audio output, you ca n connect it to the A V re cei ver’ s multichannel inpu t.
33 Connecting the A V receiver —Continued W ith this hookup, you can use your VCR’ s tuner to li sten to your fav orite TV programs via the A V receiv er, useful if your TV has no audio outputs. • W ith connection , you can listen to the VCR or D VD recorder in Zone 2 or Zone 3.
34 Connecting the A V receiver —Contin ued Notes: • The A V recei ver must be turned on for recording. Recording is not possible while it’ s in Standby mode.
35 Connecting the A V receiver —Continued W ith this hookup, you can use your satellite or cable receiv er to listen to your fa vorite TV programs via the A V recei ver, useful if your TV has no audio outputs. • W ith connection , you can listen to and record audi o from the video source or listen in Zone 2 or Zone 3.
36 Connecting the A V receiver —Contin ued • W ith connection , you can listen to and record audio from your game cons ole or listen in Zone 2 or Zone 3. • T o enjoy Dolby Digital and DTS, use connection . (T o record or listen in Zone 2 or Zone 3 as well, use and .
37 Connecting the A V receiver —Continued Connecting a Camcor der or Other Device Connection A V receiver Signal flow Camcorder etc. A UX INPUT VIDEO ⇐ Composite video output AU X I N P U T L - AU D I O - R ⇐ Analog audio L/R output AU X I N P U T D I G I T A L ⇐ Digital optical output Step 1: Video Connection Make the connection .
38 Connecting the A V receiver —Contin ued ■ CD Player or T urntable (MM) with Built-in Phono Preamp • W ith connection , you can listen to and record audio from your CD player or listen in Zone 2 or Zone 3. • T o connect the CD player di gitally , use connection or .
39 Connecting the A V receiver —Continued • W ith connection , you can play and re cord or listen in Zone 2 or Zone 3. • T o connect the recorder digitally for playback, use connections and , or and .
40 Connecting the A V receiver —Contin ued If you want to use a more powerful po wer amplif ier and use the A V receiver as a preamp, connect it to the PRE OUT jacks, and connect all sp eakers and the subwoofer to the po wer amplif ie r . Y ou can connect the powered subwoofer with each jacks respectiv ely .
41 Connecting the A V receiver —Continued ■ If Y our iP od Supports Video: Connect your RI Dock’ s audio output jacks to the A V receiv er’ s GAME IN or VCR/D VR IN L/R jacks, and connect its video output jack to the A V receiv er’ s GAME IN V or VCR/D VR IN V jack.
42 Connecting the A V receiver —Contin ued W ith u (Remote Interacti ve) , you can use the follow- ing special functions: ■ A uto P ower On/Standb y When you start playba ck on a component conn ected via u , if the A V rec eiv er is on Standby , it will auto- matically turn on and sele ct that component as the input source.
43 T urning On the A V receiver European and Asian models : T o completely shut do wn the A V recei ver, set the [PO WER] switch to the OFF position () .
44 Firs t Time Setup This section explains the se ttings that you need to make before using the A V receiv er for the v ery first time. If you connect your TV to HDMI OUT MAIN, “Monitor Out” setti.
45 First Time Setup —Continued In this Instruction Manual, i llu strations from the onscreen menu or e xplanat ions referring to the menu will be in the same language as the Instruct ion Manual. The defa ult Langua ge setting for the onscreen menu is English.
46 First Time Setup —Contin ued Carry out the settings for th e A V rece iv er by using the Onscreen Setup Menu. The settings of the A V receiv er can be changed using the Display . Onscreen Setup Men us and Displa y As each item in the On screen Setup Menus is selected, the selected it ems will be displayed one by on e.
47 First Time Setup —Continued If you connect your TV to the HDMI output, set the “Monitor Out” setting so that the ons creen setup me nus are displayed and composit e video, S-V ideo, and component video sources are upcon ve rted and output.
48 First Time Setup —Contin ued Notes: • See page 27 for charts sho wing how the “Monitor Out” and “Resolution” setti ngs af fect the video signal flow through the A V receiver. • This procedure can also be performed on the A V recei ver by using its [SET UP] button, arro w buttons, and [ENTER] button.
49 First Time Setup —Continued HDMI Input Setup If you connect a video component to HDMI IN, you must assign that input to an input selector . For example, if you connect your D VD/BD player to HDMI IN 1, you must assign HDMI IN 1 to the D VD/BD input selector .
50 First Time Setup —Contin ued Component Video Input Setup If you connect to a COMPONENT VIDEO IN, you must assign it to an input select or . For example, if you connect your D VD/BD player to COMPONENT VIDEO IN 2, you should assign it to the D VD/BD input selector .
51 First Time Setup —Continued If you connect a component to a digital input jack, you must assign that jack to an i nput selector . For example, if you connect your CD player to the OPTICAL IN1 jack, you should assign that jack to the CD input selector .
52 First Time Setup —Contin ued If you connect a component to the A V receiv er’ s analog multichannel input, you must assign that input to an input selector . F or example, if you connect your D VD/ BD player to the MUL TI CH input, you mu st assign it to the D VD/BD input sele ctor .
53 First Time Setup —Continued If the impedance of any speaker is 4 ohms or more but less than 6, set the minimum speaker impedance to 4 ohms. If you’ ve connected your front speak ers to the FRONT L/R and SURR BA CK/ZONE 3 L/R terminal posts for bi-amping, you must change the “Speakers T ype(Front)” setting.
54 First Time Setup —Contin ued For the on screen setup menus to display properly , you must specify the TV system used in your area. Note: This procedure can also be perform ed on the A V recei ver by using its [SETUP] b utton, arro w buttons, and [ENTER] button.
55 First Time Setup —Continued Note: This procedure can also be performed on the A V receiver by using its [SETUP] b utton, arrow b uttons, and [ENTER] button.
56 First Time Setup —Contin ued W ith the supplied calibrated microphone, Audyssey MultEQ XT automat ically determines the number of speakers connected, their size for purposes of bass management, optimum cro sso ver frequencies to the subwoofer (if present), and distances from the primary listening position.
57 First Time Setup —Continued Using A ud yssey MultEQ ® XT ENTER ON/ST ANDBY qwer Speaker setup microphone Notes: • If any of your sp eakers is 4 ohms, change “Speaker Impedance” se tting before runnin g Audyssey MultEQ X T Room Correction and Speaker Setup (see page 53).
58 First Time Setup —Contin ued • Make the room as quiet as possible. Background noise can disrupt the room measurements. Close windows, silence cell phones, television s, radios, air conditioners, fluorescent lights, home appliances, light dimmers, or other devices.
59 First Time Setup —Continued Notes: • When the room correcti on and speaker setup is complete, the “Equalizer Sett ings” (page 93) will be set to “Audyssey” and “Dyna mic EQ” (page 97) will be set to “On”.
60 First Time Setup —Contin ued One of the front speakers has not been detected. One of the front wide speak ers has not been detected. One of the front high speakers has not been detected. One of the surround speakers has not been detected. The surround back speakers ha ve been detected but the surround speake rs hav en’t.
61 First Time Setup —Continued The speaker type detected does not match what was expected. The speak er may be incorrect type or bro- ken. Please chec k that it is t he correct speaker type.
62 Basic Operations This section explains ho w to select the input source (i.e., the A V compone nt that you want to listen to or watch). Selecting the Input Sour ce 1 Use the A V receiv er’ s input select or b uttons to select the input sour ce.
63 Basic Operations —Continued Y ou can adjust the bass and treble for the front speakers, except when the Direct, Pu re Audio or THX listening mode is selected. ■ Bass Y ou can boost or cut lo w-fre quency sounds output by the front speakers from –10 dB to +10 dB in 2 dB steps.
64 Basic Oper ations —Continued Y ou can adjust the brightness of the A V receiv er’ s dis- play . Y ou can tempor arily mute the output of the A V receiv er. Tip : Y ou can sp ecify how much the output is muted with the “Muting Le vel” setting (page 105).
65 Basic Operations —Continued Y ou can select the priority of the use of Front High speakers or Front W i de speakers. Notes: • If the Powered Zone 2 is being used (page 127), this setting cannot be selected. • When the listening mode that doesn’t support Fro nt High or Front W ide speakers is used, the setting can- not be selected.
66 Basic Oper ations —Continued Using the Easy macro comm and in the Easy macro mode, you can sequentially ope rate Onk yo components with simple commands by simply pressing one button. These commands are user-spe cifi able (see page 143) and the default ac tions are described belo w .
67 Basic Operations —Continued Changing Sour ce Component When you want to operate the component that is not assigned as the source component, you can assign it as the source component.
68 Listening to the Radio W ith the built-in tun er you can enjoy AM and FM radio stations. Y ou can store your fav orite stations as presets for quick selection. Listening to the Radio T uning into Radio Stations ■ Auto T uning Mode When tuned into a station, the T UNED indicator appears.
69 Listening to the Radio —Continued Y ou can store a combination of up to 40 of your fa vorite AM/FM radio stati ons as presets. Note: Y ou can name yo ur radio pr esets for easy identification (see page 100). Its name is display ed instead of the band and frequency .
70 Listening to the Radio —Continued RDS only works in ar eas where RDS br oadcasts ar e av ailable. When tuned into an RDS st ation, the RDS indicator appears. ■ What is RDS? RDS stands for Radio Data System and is a method of transmitting data in FM radi o signals.
71 Listening to the Radio —Continued When tuned to an RDS station th at’ s broadcasting text informat ion, the te xt can be displayed. Displa ying Radio T ext (RT) Notes: • The message “ W aiting ” may appear while the A V recei ver waits for the R T information.
72 Universal P or t Option UP-A1 Doc k f or iP od W ith the UP-A1 Dock (sold separately), you can easily play the music, photo, or movie stored on your Apple iPod through the A V receiv er and enjoy great sound. Y ou can use the A V recei ver’ s remote controller to operate your iPod.
73 Universal P or t Option UP-A1 Dock f or iP od —Contin ued By pressing the REMO TE MODE button that’ s been programmed with the remote control code for your Dock, you can control your iPod in the Dock with the following b uttons.
74 Universal P or t Option UP-A1 Dock f or iP od —Contin ued Status messag es ❏ PORT Reading The A V recei ver is checki ng the connection with the dock. ❏ PORT Not Support The A V recei ver do not support the connected dock. ❏ PORT UP-A1 UP-A1 Dock is connected.
75 Recor ding This section explains ho w to record the selected input source to a component with re cording ca pability , and how to record aud io and video from different sources. Notes: • The surround sound and D SP listening modes cannot be recorded.
76 Using the Listening Modes See “ About the Listening Modes” on page 84 for detailed information a bout the listening modes. Selecting on the A V receiver ■ [PURE A UDIO] b utton This button selects the Pure Audio listening mode.
77 Using the Listening Modes —Continued Mono/Multiple x Sourc es ✔ : A vail able Li stening Modes Notes: *1 For 7ch output, output can b e switched between Fron t high or Fro nt wide spea kers by pressing the [ SP LA YOUT] button (dependi ng on the “Speake r Config uration” settin g (see page 90)) .
78 Using the Listening Modes —Continued Stereo Source (1/2) ✔ : A vailable Listening Modes Listening Mode But ton Speaker lay out Pure A udio *5 ✔✔✔✔ Direct ✔✔✔✔ Stereo ✔✔✔.
79 Using the Listening Modes —Continued Stereo Sour ce (2/2) ✔ : A vail able Li stening Modes Notes: *1 For 7ch output, output can b e switched between Fron t high or Fro nt wide spea kers by pressing the [ SP LA YOUT] button (dependi ng on the “Speake r Config uration” settin g (see page 90)) .
80 Using the Listening Modes —Continued 5.1 channel Sour ces (1/3 ) ✔ : A vailable Listening Modes Listening Mode But ton Speaker lay out Pure A udio* 5 ✔✔✔✔ Direct ✔✔✔✔ Stereo ✔.
81 Using the Listening Modes —Continued 5.1 chan nel Sourc es (2/3) ✔ : A vail able Li stening Modes Listening Mo de Button Speaker lay out PLIIx Music THX Music ✔ PLIIx Music Au dyssey DSX ✔ .
82 Using the Listening Modes —Continued 5.1 channel Sour ces (3/3 ) ✔ : A vailable Listening Modes Notes: *1 For 7ch output, o utput can be s witched betwe en Front hig h or Front wide s peakers by pressin g the [SP LA YOUT] button (depend ing on the “Speaker Configuration ” setting (see page 90 )).
83 Using the Listening Modes —Continued 7.1 chan nel Sourc es ✔ : A vail able Li stening Modes Listening Mo de Button Speaker lay out Pure A udio* 5 ✔✔✔✔ Direct ✔✔✔✔ Stereo ✔✔.
84 Using the Listening Modes —Continued Notes: *1 For 7ch output, o utput can be s witched betwe en Front hig h or Front wide s peakers by pressin g the [SP LA YOUT] button (depend ing on the “Speaker Configuration ” setting (see page 90 )).
85 Using the Listening Modes —Continued 5.1-cha nnel sour ce + Do lby E X These modes expand 5.1-cha nnel sources for 6.1/7.1- channel playback. They’ re espe ci ally suited to Dolb y EX soundtracks that include a matrix-encoded surround back channel.
86 Using the Listening Modes —Continued THX Founded b y George Lucas, THX de velops stringent stan- dards that ensure movies are reproduced in movie the- aters and home theaters just as the director intended. THX Modes carefully optimiz e the tonal and spatial characterist ics of the soundt rack for reproduction in the home-theater en vironment.
87 Ad v anced Setup The onscreen setup menus appear on the connected TV and provide a con venient way to change the A V receiver’ s variou s settings. Settings are orga nized into nine categories on the main menu , most containing a submenu . Onscreen Setup Menu s 1.
88 Adv anced Setup —Continued This section explai ns items on the “Input/Output Assign” menu. Note: This procedure can also be perform ed on the A V recei ver by using its [SETUP] b utton, arro w buttons, and [ENTER] button. Input/Output Assign 1 Press the [RECEIVER] button f ollowed b y the [SETUP] button.
89 Adv anced Setup —Contin ued Component Video Input See “Component V ideo Input Setup” on page 50. Digital Audio Input See “Digital Audio Input Setup” on page 51.
90 Adv anced Setup —Continued Some of the se ttings in this se ction are set auto matically b y Audyssey MultEQ ® XT Room Correction and Speaker Setup (see page 56).
91 Adv anced Setup —Contin ued Surr Back Ch *7 1ch: Select if only one surround ba ck L speaker is connected. 2ch: Select if two (lef t and right) surround back speak ers are connected (default).
92 Adv anced Setup —Continued Speaker Distance This setting is set automatically b y Audyssey MultEQ ® XT Room Correction and Speaker Setup (see page 56). Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arriv es at the listener’ s ears as the sound designer intended.
93 Adv anced Setup —Contin ued Equalizer Settings This setting is set automati cally by Audyssey M ultEQ ® XT Room Correction and Sp eaker Setup (see page 56). W ith the Equalizer settings, you can adjust the tone of speakers indi vidually wi th a 7-band equalizer .
94 Adv anced Setup —Continued THX A udio Set up This setting is not set automati cally by Audyssey Mult EQ ® XT Room Correction and Sp eaker Setup (see page 56). W ith the “SurrBack Sp Spacing” setting, y ou can specify the distan ce between your surround back speakers.
95 Adv anced Setup —Contin ued W ith the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like. Note: This procedure can also be performed on the A V recei ver by using its [SETUP] bu tton, arrow b uttons, and [ENTER] button.
96 Adv anced Setup —Continued Dolby PLIIx Music (2ch Input) These settings apply to only 2-channel stereo sources. If you’ re not using an y surround back speakers, these settin gs ap ply to Dolby Pro Logic II, instead of Dolby Pro Logic IIx. Pano ra ma On: Panorama function on.
97 Adv anced Setup —Contin ued Aud yssey For “Dynamic EQ”, “Reference Le vel” and “Dynamic V olume”, you cannot cha nge the settings be fore completing Audyssey MultEQ ® XT Room Correction and Speak er Setup. Dyn amic E Q Off: Audyssey Dynamic EQ™ of f (default).
98 Adv anced Setup —Continued Theater-Dimensional Listening Angle Wi de: Select if the listening angle is greater than 30 de grees (default ). Narrow: Select if the listening angle is less than 30 degrees.
99 Adv anced Setup —Contin ued This section e xplains items on the “S ource Setup” menu. Items can be set indi vidually fo r each input selector . Note: This procedure can also be performed on the A V recei ver by using its input select or buttons, [SETUP] b utton, arrow b uttons, and [ENTER] b utton.
100 Adv anced Setup —Continued Name Edit Y ou can enter a custom name for each indi vidual input selector (e xcluding TUNER) and radio preset for easy identi- fica tion.
101 Adv anced Setup —Contin ued Zoom Mode This setting de termines the aspect ratio. Note: When the “Ga me Mode” is se t to “On”, th e “Zoom Mode” is fixed at “Full”.
102 Adv anced Setup —Continued ISF Mode Custom: User setting (All it ems can be freely set.) Day: Setting when a room is bright. Night: Setting when a room is dark. The receiv er has been designed to in corporate setup and calibr ation standards establis hed by the Imaging Sci- ence Foundation (ISF).
103 Adv anced Setup —Contin ued Brightness *1 –50 to +50 (def ault: 0) W ith this setting you can adjust the picture brightne ss. “–50” is the darkest. “+50” is the brightest. Contrast *1 –50 to +50 (default: 0) W ith this setting you can adju st contrast.
104 Adv anced Setup —Continued Y ou can assign a def ault listeni ng mode to each input source that will be selected automatically when you select each input source. For e xample, you can set the default listening mode to be used wi th Dolby Digital i nput signals.
105 Adv anced Setup —Contin ued This section explains the it ems on the “Miscellaneous” menu. Note: This procedure can also be performed on the A V recei ver by using its [SETUP] bu tton, arrow b uttons, and [ENTER] button. Miscellaneous (V olume/OSD) Setup 1 Press the [RECEIVER] button f ollowed by the [SETUP] b utton.
106 Adv anced Setup —Continued . This section explai ns items on the “Hardware Setup” menu. Note: This procedure can also be perform ed on the A V recei ver by using its [SETUP] b utton, arro w buttons, and [ENTER] button. OSD Setup Immediate Disp lay On: Displayed (default).
107 Adv anced Setup —Contin ued Remote ID Remote ID 1, 2, 3 When se veral Onkyo components are used in the same room, their remote ID codes may o verlap. T o dif feren- tiate the A V recei ver from the othe r components, you can ch ange its remote ID from 1, the default, to 2 or 3.
108 Adv anced Setup —Continued HDMI A u dio TV Ou t Off: HDMI audio is not output to TV (default). On: HDMI audio is output to TV and the sound will be heard from the TV speakers. This preference dete rmines whethe r audio recei ved at the HDMI input is output from the HDMI outp uts.
109 Adv anced Setup —Contin ued HDMI Control (RIHD) On: enabled. Off: disabled (def ault). This function allows -compatibl e components connected via HDMI to be controlled with the A V recei ver. Notes: • , which stands for Remote Interactiv e ov er HDMI, is the name of the sy stem control function found on Onkyo components.
110 Adv anced Setup —Continued Network See “Network Settings” on page 121. Firmware Update Notes: • Perform the firmware update only when an announcement is posted on the Onkyo W eb site. • It take s about 60 minutes to complete the f irmware updat e.
111 Adv anced Setup —Contin ued W ith this preference, you ca n protect your settings by locking the setup menus. Note: This procedure can also be performed on the A V receiver by using its [SETUP] b utton, arrow b uttons, and [ENTER] button.
112 Adv anced Setup —Continued Y ou can change various audio setting s by pressing the [A UDIO] b utton. Note: When the “Audio TV Out” setting is set to “On” (page 108), the [A UDI O] button is disabled. Using the A udio Settings AU D I O RECEIVER qwer 1 Press the [RECEIVER] button f ollowed b y the [A UDIO] button.
113 Adv anced Setup —Contin ued Re-EQ Function W ith the Re-EQ function, you can compensate a soundtrack whose high-frequency conten t is too harsh, making it more suitable for home theater viewing. Re-EQ Off: Re-EQ Function off (default). On: Re-EQ Function on.
114 Adv anced Setup —Continued Speaker Levels Y ou can adjust the volume of each spea ker while listening to an input source. These temporary adjustments are ca ncelled when the A V receiv er is set to Standb y . T o sa ve the setting you made here, go to “Le v el Calibration” on page 92 before setting the A V receiv er to Standb y .
115 NET The A V recei ver is network-ready , which means you can hook it up to your home network with a standard Ether- net cable and enjoy the musi c fi les stored on your com- puter or media server . If your network is connected to the Internet, you can also enjoy Internet radio.
116 NET —Continued T o receiv e Internet radi o, you must connect the A V recei ver to a netw ork with Internet access (page 115). Y ou can select Internet radi o stations by connecting to the A V receiv er from your co mputer and se lecting sta- tions in your W eb bro wser .
117 NET —Continued This section explains ho w to play music files on a com- puter or media server through the A V receiv er. See page 115 for details on supported music servers and music fi le formats. For W indo ws Media Player 11, see “W indows Media Player 11 Setup” on page 1 18.
118 NET —Continued Random Playback The Random function can only be set while the PLA Y screen is displayed. T o play songs in random or der , during p layback (or while playback is paused or stopped), press the [RAN- DOM] button. All of the songs in the cu rrent folder will be played in random order .
119 NET —Continued Supported A udio File Formats For serv er playback, the A V recei ver supports the fol - lo wing music file formats: MP3, WMA, W A V , FLA C, Ogg V orbis, AA C and LPCM. ■ MP3 • MP3 files must be MPEG -1/MPEG-2 Audio Layer 3 format with a sampling rate of 8 kHz, 11.
120 NET —Continued Server Requirements The A V recei ver ca n play digital music f iles stored on a computer or media server and supports the follo wing technologies: • W indo ws Media Player 11 • W indo ws Media Connect 2.
121 NET —Continued Note: When modifying network sett ings, after modifying it is necessary to ex ecute “Save”. This section explains ho w to configure the A V receiver’ s network settings manually .
122 NET —Continued Mac Add ress This is the A V recei ver’ s MAC (Medi a Access Control) address. This addre ss cannot be changed. DHCP This setting determines whet her or not the A V receiv er uses DHCP to automatically conf igure its IP Address, Subnet Mask, Gate way , a nd DNS Server settings.
123 Multi Zone Y ou can use three speaker systems with this A V receiver —a surround-sound sp eaker system (up to 9.2 channels) in your main listening room, Zone 2: a stereo speak er system in a second room, Zone 3: a stereo speaker system in a third room.
124 Multi Zone —Continued In addition to your main listening room, you can also enjoy pl ayback in the other room, or as we call Multi Zone. And, you can select a different source for each room. There are two w ays you can connect Zone 2 speakers: 1.
125 Multi Zone —Continued Zone 2 Video Output The A V rece iv er features a composite video output for connection to a TV in Zone 2, so you can enjoy both audio and video in that zone. Hookup • Use a composite video ca ble to connect the A V recei ver’ s ZONE 2 OUT V ja ck to a composite video input on your Zone 2 TV .
126 Multi Zone —Continued There are two w ays you can connect Zone 3 speakers: 1. Connect them directly to the A V receiv er. 2. Connect them to an amp in Zone 3.
127 Multi Zone —Continued If you’ ve connected your Zon e 2/3 speakers to the A V receiv er, as explained in “Connecting Y our Zone 2 Speakers Directly to the A V recei ver” on page 124 or “.
128 Multi Zone —Continued Note: This procedure can also be perform ed on the A V recei ver by using its [SETUP] b utton, arro w buttons, and [ENTER] button.
129 Multi Zone —Continued This section explains ho w to turn Zone 2/3 on and off, how to select an input source for Zone 2/3, and ho w to adjust the volume for Zone 2/3. Contr olling Zone 2/3 f rom the A V receiver Note: When Zone 2/3 is turned off, the output from the 12V TRIGGER OUT ZONE 2/3 goes low (0 v olts).
130 Multi Zone —Continued Notes: • Only analog input sources are output by the ZONE 2/ 3 PRE OUT and ZONE 2/3 L/R speaker terminals. Digital input sources are not output. If no sound is heard when an input source is selected, check if it’ s connected to an analog input.
131 Multi Zone —Continued T o control the A V receiv er with the remote controller while you’ re in Zone 2 or Zone 3, you’ll need a commer- cially a vail able multiroom remote contro l kit for each zone. • Multiroom kits are made b y Niles and Xantech.
132 Contr olling Other Components Y ou can use the A V receiv er’ s remote cont roller (RC-745M) to control your other A V components, including those made by ot her manufacturers. This sec- tion explains ho w to enter the remote control code for a component that you want to control: D VD, TV , VCR, etc.
133 Contr olling Other Components —Continued 5 Use the Up and Down [ q ]/[ w ] but- tons to select category , and then press [ENTER]. The brand name i nput panel appears. 6 Use the arrow [ q ]/[ w ]/[ e ]/[ r ] b ut- tons to select a character , and then press [ENTER].
134 Controlling Other Components —Contin ued Y ou’ ll need to enter a code for each component that you want to control. Note: The remote control codes pro vided are correct at the time of printing, but are subject to change.
135 Contr olling Other Components —Continued Onkyo components that are connected via u are con- trolled by pointing the remote controller at the A V receiv er, not the component. This allows you to control components that are out of vie w , in a rack, for e xample.
136 Controlling Other Components —Contin ued By pressing the [TV] button that’ s been programmed with the remote control code for TV , you can control your TV with the follow ing buttons. For detail s on entering a remote control code for a differ- ent component, see page 134.
137 Contr olling Other Components —Continued By pressing the REMO TE MODE button that’ s been programmed with the remote control code for your D VD player (HD D VD, Blu-ray , or TV/D VD combination), you can control your player with the follo wing b uttons.
138 Controlling Other Components —Contin ued t PLA Y MODE button* Selects play modes on com ponents with selectable play modes. u CLR button Cancels functions and cl ears entered numbers. Notes: • W ith some components, cert ain buttons may no t work as expected, and some may not w ork at all.
139 Contr olling Other Components —Continued By pressing the REMO TE MODE button that’ s been programmed with the remote control code for your sat- ellite recei v er , cable recei ver , or D VD recorder (DBS/ PVR combination or cable/ PVR combination), you can control your player with the follow ing buttons.
140 Controlling Other Components —Contin ued By pressing the REMO TE MODE button that’ s been programmed with the remote contr ol code for your CD player , CD recorder , or MD recorder , you can control your player with the following b uttons. The [CD] b utton is preprogrammed with the remote con- trol code for controlling an Onk yo CD player .
141 Contr olling Other Components —Continued By pressing the REMO TE MODE button that’ s been programmed with the remote control code for your Dock, you can control your iPod in the Dock with the following b uttons. For some RI do cks, the [ON], [ST ANDBY] button may not work with a remote control cod e 82990 (without u ).
142 Controlling Other Components —Contin ued r PLA Y MODE button Selects play modes on com ponents with selectable play modes. W orks as a Resume button when used with a DS-A2 RI Dock. s RANDOM button Used with the shuf fle function. Note: W ith some components, certai n buttons may not work as expected, and some may not work at all.
143 Contr olling Other Components —Continued V ia onscreen menu, you can sp ecify what actions will be taken b y the Easy macro command in the Easy macro mode. Activities Setup 1 Press the [RECEIVER] button fol- lowed b y the [SETUP] b utton. The main menu appears onscreen.
144 Controlling Other Components —Contin ued Here ar e the default setting s. Source Play Enable: Start playback the sou rce of “Enable”. Disable: Start playback the sou rce of “Disable”. This option enables the Source to start playback when t he A CTIVI- TIES butto n is pressed.
145 Contr olling Other Components —Continued The A V rece iv er’ s remote controller can learn the com- mands of other remote contro llers. By tra nsmitting, for example, the Play command from you.
146 Controlling Other Components —Contin ued Y ou can program the remote controller’ s ACTIVI TIES buttons to perform a sequence of r emote control actions. Example: T o play a CD you typically need to perform the follow- ing actions: 1. Press the [RECEIVER] b utton to select the Rece iv er remote controller mode.
147 T roub leshooting If you hav e any trouble using the A V receiv er, look for a solution in this section. If you can’ t resolve the issue yourself, contact your Onkyo dealer . Can’t turn on the A V receiver • Make sure that the po wer cord is properly plugged into the wal l outlet.
148 T r oubleshooting —Continued The surround speaker s produce no sound • When the DTS Surround Sen sation, T -D (Theater- Dimensional), Stereo or Mono listening mode is selected, the surround speakers produce no sound. • Depending on the source a nd current list ening mode, not much sound may be produced by the surround speakers.
149 T r oubleshooting —Contin ued • W ith some CD and LD players, you won’t be able to playback DTS material properly even though your player is connected to a digital input on the A V recei ver. This is usually because the DTS bitstream has been processed (e.
150 T r oubleshooting —Continued The remote controller doesn’t w ork • Make sure that the batteries are installed wit h the cor- rect polarity (page 14). • Install ne w batteries. Don’t mix diff erent types of bat- teries, or old and new batteries (page 14).
151 T r oubleshooting —Contin ued Can’t record • On your recorder , mak e sure the correct input is selected. • T o prev ent signal loops and damage to the A V recei ver, input signals are not fed through to outputs wit h the sam e na me ( e.g.
152 T r oubleshooting —Continued The follo wing settings can be made fo r the S- Video, composite vi deo and COMPONENT VIDEO inputs Y ou must use the buttons on the A V receiv er to make these settings. 1. While holding do wn the input selector button for the input source that you want to set, press the [SETUP] button.
153 Specifications Amplifier Sect ion Video Section T uner Sectio n General ■ Video Inputs ■ Video Outputs ■ A udio Inputs ■ A udio Outputs ■ Control T ermi nal Specifications and features ar e subject to change without notice.
154 Video Resolution Char t The following tables sho w how vide o signals at different resolutions are output by the A V receiver. *1: The output i s limited to 480p for an effectiv e signal i n the effect of Macr ovision.
155 Memo.
156 SN 29400052 Y0907-1 (C) Copyright 2009 ONKY O CORPORA TION Japan. All rights reserved. http://www.onkyo.com/ HOMEPAGE Sales & Product Planning Div . : 2-1, Nisshin-cho , Ney agawa-shi, OSAKA 572-8540, J AP AN T el: 072-831-8023 F ax: 072-831-8163 ONKY O U .
デバイスOnkyo TX-NR1007の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Onkyo TX-NR1007をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOnkyo TX-NR1007の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Onkyo TX-NR1007の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Onkyo TX-NR1007で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Onkyo TX-NR1007を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOnkyo TX-NR1007の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Onkyo TX-NR1007に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOnkyo TX-NR1007デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
