OpelメーカーAntara (2015)の使用説明書/サービス説明書
ページ先へ移動 of 221
OPEL Antara Owner's Manual.
.
Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 20 Seats, restraints ........................... 35 Storage ........................................ 57 Instruments and controls .
2 Introduction Introduction.
Introduction 3 Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate.
4 Introduction 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage.
Introduction 5.
6 In brief In brief Initial drive information Vehicle unlocking Press button q to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, operate button above number plate. Radio remote control 3 20, Central locking system 3 22, Load compartment 3 24.
In brief 7 Seat backrests Pull lever, adjust inclination and release lever. Allow the backrest to engage audibly. Do not lean on the seat backrest whilst adjusting it. Seat position 3 36, Seat adjustment 3 37, Seat folding 3 38. Seat height Lever pumping motion up = seat higher down = seat lower Seat position 3 36, Seat adjustment 3 37.
8 In brief Positioning = move front switch forwards/ backwards Height of front part of seat = move front part of front switch upwards/ downwards Height of rear part of seat = move rear part of front s.
In brief 9 Mirror adjustment Interior mirror To reduce dazzle, adjust the lever on the underside of the mirror housing. Interior mirror 3 30, Automatic anti- dazzle interior mirror 3 30. Exterior mirrors Select the relevant exterior mirror and adjust it.
10 In brief Instrument panel overview.
In brief 11 1 Side air vents ..................... 121 2 Fixed air vents .................... 122 3 High beam .......................... 108 Headlight flash ................... 108 Turn and lane-change signals ................................ 110 Exit lighting .
12 In brief.
In brief 13 Exterior lighting Turn light switch: AUTO = Automatic light control: Headlights are switched on and off automatically depending on external lighting conditions. 7 = Off (or deactivation of automatic light control) 8 = Sidelights 9 = Headlights Press button: > = Front fog lights r = Rear fog light Lighting 3 107.
14 In brief Turn and lane-change signals right = lever up left = lever down Turn and lane-change signals 3 110, Parking lights 3 111. Hazard warning flashers Operated with the ¨ button.
.
16 In brief Climate control Heated rear window, heated exterior mirrors Heating is operated by pressing the R Ü button. Heated rear window 3 32, Heated exterior mirrors 3 29.
In brief 17 Transmission Manual transmission Reverse: with the vehicle stationary, wait 3 seconds after depressing clutch pedal and engage the gear. If the gear does not engage, set the lever to neutral, release the clutch pedal and depress again; then repeat gear selection.
18 In brief Starting the engine ■ Turn key to position ACC ■ move the steering wheel slightly to release the steering wheel lock ■ manual transmission in neutral ■ operate clutch and brake ped.
In brief 19 For vehicles with automatic transmission, depress foot brake and shift into P before pushing key into ignition switch and removing. ■ If the vehicle is on a level surface or uphill slope, engage first gear or move the selector lever to P before switching off the ignition.
20 Keys, doors and windows Keys, doors and windows Keys, locks ................................... 20 Doors ........................................... 24 Vehicle security ............................ 25 Exterior mirrors ............................ 28 Interior mirrors .
Keys, doors and windows 21 Used to operate: ■ Central locking system ■ Anti-theft locking system ■ Anti-theft alarm system The radio remote control has a range of approx. 6 metres. This range can be affected by external influences. The hazard warning flashers confirm operation.
22 Keys, doors and windows Central locking system Unlocks and locks doors, load compartment and fuel filler flap. A pull on an interior door handle unlocks the respective door. Pulling the handle once more opens the door. Note In the event of an accident in which airbags or belt pretensioners are deployed, the vehicle is automatically unlocked.
Keys, doors and windows 23 The tailgate is unlocked together with the doors. With the engine running, the tailgate will only unlock when the electrical parking brake is applied or automatic transmission is in position P . Central locking buttons Locks or unlocks all doors, the load compartment and fuel filler flap from the passenger compartment.
24 Keys, doors and windows Doors Load compartment Tailgate Opening Operate the button above the number plate and lift the tailgate. If the tailgate is open when the ignition is switched on, control indicator 1 illuminates in the instrument cluster 3 92.
Keys, doors and windows 25 gases, which cannot be seen or smelled, could enter the vehicle. This can cause unconsciousness and even death. Caution Before opening the tailgate check overhead obstructions, such as a garage door, to avoid damage to the tailgate.
26 Keys, doors and windows It monitors: ■ Doors, tailgate, bonnet ■ Passenger compartment including adjoining load compartment ■ Vehicle inclination, e.g. if it is raised ■ Siren power supply ■ Ignition Unlocking the vehicle deactivates both systems simultaneously.
Keys, doors and windows 27 3. Close doors. 4. Activate the anti-theft alarm system. Press button o again to cancel. Control indicator o extinguishes. Status LED Status LED is located in the centre console. Status during the first 30 seconds of anti-theft alarm system activation: LED illuminates = test, arming delay.
28 Keys, doors and windows Immobiliser The system is part of the ignition switch and checks whether the vehicle is allowed to be started with the key being used. The immobiliser is activated automatically after the key has been removed from the ignition switch.
Keys, doors and windows 29 Folding mirrors For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force. Reposition the mirror by applying slight pressure to the mirror housing. Manual folding Press lightly on the outside of the mirror housing to fold in the exterior mirrors.
30 Keys, doors and windows Do not use sharp instruments or abrasive cleaners on the exterior mirrors and avoid scratching or damaging the heating elements. Automatic dimming Exterior mirror on the driver's side dims to reduce glare automatically in conjunction with the automatic anti- dazzle interior mirror 3 30.
Keys, doors and windows 31 Windows Windscreen Heat-reflecting windscreen The heat-reflecting windscreen has a coating which reflects solar radiation. Also data signals, e.g. from toll stations, might be reflected. The marked areas of the windscreen behind the interior mirror are not covered with the coating.
32 Keys, doors and windows Additional switches are located in the front passenger's door and the rear doors. The rear windows do not open fully. Safety function If the window glass encounters resistance above the middle of the window during automatic closing, it is immediately stopped and opened again.
Keys, doors and windows 33 Do not use sharp instruments or abrasive cleaners on the rear window and avoid scratching or damaging the heating elements. Sun visors The sun visors can be folded down or swivelled to the side to prevent dazzling. Sun visors have vanity mirrors and a ticket holder on the rear.
34 Keys, doors and windows General hints Function standby The sunroof can be operated: ■ with ignition on, ■ within 10 minutes of switching ignition off, After switching off the ignition, sunroof operation is disabled when driver's door is opened.
Seats, restraints 35 Seats, restraints Head restraints ............................ 35 Front seats ................................... 36 Rear seats ................................... 40 Seat belts ..................................... 42 Airbag system .
36 Seats, restraints Stow head restraints securely in load compartment. Active head restraints In the event of a rear-end impact, the active head restraints automatically tilt forwards. Thus the head is supported so that the risk of whiplash injury is reduced.
Seats, restraints 37 Seat adjustment 9 Danger Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. 9 Warning Never adjust seats while driving as they could move uncontrollably. Drive only with engaged seats and backrests.
38 Seats, restraints Seat height Lever pumping motion up = seat higher down = seat lower Lumbar support Adjust lumbar support to suit personal requirements using the lever.
Seats, restraints 39 Slide seat forwards. To return the backrest to its original position, slide seat as far back as it will go, lift release lever, move the backrest to upright position, lower lever and the backrest engages. Folding the backrest forwards is possible only when the backrest is in an upright position.
40 Seats, restraints Heating Adjust heating to the desired setting by pressing the ß button for the respective seat one or more times with the ignition switch set to ACC or ON . The control indicator in the button indicates the setting. To deactivate heating, set the heating level to its lowest setting and press the ß button.
Seats, restraints 41 9 Warning Never adjust seats while driving as they could move uncontrollably. Seat folding The load compartment can be enlarged by folding the seat backrests onto the seat cushions. To fold backrests separately, unbuckle all three rear seat belts and ensure front seats are not in a reclined position.
42 Seats, restraints Seat belts The seat belts are locked during heavy acceleration or deceleration of the vehicle holding the occupants in the seated position. Thereby the risk of injury is considerably reduced. 9 Warning Fasten seat belt before each trip.
Seats, restraints 43 pretensioners. Do not make any modifications to belt pretensioner components as this will invalidate the vehicle type approval. Three-point seat belt Fastening Withdraw the belt from the retractor, guide it untwisted across the body and insert the latch plate into the buckle.
44 Seats, restraints Adjust the height so that the belt lies across the shoulder. It must not lie across the throat or upper arm. Do not adjust while driving.
Seats, restraints 45 Front passenger seat belt reminder When the engine is running, control indicator k flashes then illuminates if the passenger seat is occupied and the seat belt is not engaged. If vehicle speed exceeds 22 km/h, k will flash for 100 seconds along with a warning chime, then illuminate until the seat belt is fastened.
46 Seats, restraints EN: NEVER use a rear-facing child restraint system on a seat protected by an ACTIVE AIRBAG in front of it, DEATH or SERIOUS INJURY to the CHILD can occur.
Seats, restraints 47 mesmo, poderá ocorrer a PERDA DE VIDA ou FERIMENTOS GRAVES na CRIANÇA. IT: Non usare mai un sistema di sicurezza per bambini rivolto all'indietro su un sedile protetto da A.
48 Seats, restraints acest lucru poate duce la DECESUL sau VĂTĂMAREA GRAVĂ a COPILULUI. CS: NIKDY nepoužívejte dětský zádržný systém instalovaný proti směru jízdy na sedadle, které je chráněno před sedadlem AKTIVNÍM AIRBAGEM. Mohlo by dojít k VÁŽNÉMU PORANĚNÍ nebo ÚMRTÍ DÍTĚTE.
Seats, restraints 49 The inflated airbags cushion the impact, thereby considerably reducing the risk of injury to the upper body and head of the front seat occupants. 9 Warning Optimum protection is only provided when the seat is in the proper position 3 36.
50 Seats, restraints Curtain airbag system The curtain airbag system consists of an airbag in the roof frame on each side. This can be identified by the word AIRBAG on the roof pillars. The curtain airbag system is triggered in the event of a side-on impact of a certain severity.
Seats, restraints 51 Use the ignition key to choose the position: * OFF = front passenger airbag systems are deactivated and will not inflate in the event of a collision. Control indicator * illuminates continuously on the passenger side of the instrument panel.
52 Seats, restraints Child restraints Child restraint systems We recommend the Opel child restraint system which is tailored specifically to the vehicle. When a child restraint system is being used, pay attention to the following usage and installation instructions and also those supplied with the child restraint system.
Seats, restraints 53 Child restraint installation locations Permissible options for fitting a child restraint system Weight and age class On front passenger seat On rear outboard seats On rear centre seat activated airbag deactivated airbag Group 0: up to 10 kg or approx.
54 Seats, restraints Permissible options for fitting an ISOFIX child restraint system Weight and age class Size class Fixture On front passenger seat On rear outboard seats On rear centre seat Group 0: up to 10 kg or approx. 10 months E ISO/R1 X IL X Group 0+: up to 13 kg or approx.
Seats, restraints 55 IL = Suitable for particular ISOFIX restraint systems of the 'vehicle-specific', 'restricted' or 'semi-universal' categories. The ISOFIX restraint system must be approved for the specific vehicle type.
56 Seats, restraints ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Permitted installation positions for specific vehicle ISOFIX child restraint systems are marked in the table by IL.
Storage 57 Storage Storage compartments ................ 57 Load compartment ....................... 69 Roof rack system ......................... 72 Loading information ..................... 72 Storage compartments 9 Warning Do not store heavy or sharp objects in the storage compartments.
58 Storage Glovebox The glovebox will illuminate when opened. The glovebox partition can be removed from its groove. Store the partition in the groove on the far left- hand side of the glovebox. The glovebox should be closed whilst driving. Lockable glovebox Lock and unlock the glovebox with the key.
Storage 59 Armrest storage Console box in front armrest To open: pull up lever and lift the lid. To close: lower lid and push it down until it latches into position. Centre console storage To access the storage compartment, power outlet and AUX input, slide the cupholder tray rearwards.
60 Storage 9 Warning No-one should be in the extension zone of the rear carrier system, risk of injury. Raise release lever. The system disengages and travels quickly out of the bumper. Completely pull out the rear carrier system until you hear it engage.
Storage 61 Install the tail lamps First remove the rear ( 1 ), then the front ( 2 ) tail lamp from the recesses. Open out the bulb holder on the back of the tail lamp completely. Push the clamping lever and push the bulb holder into the retainer until it hits the stop.
62 Storage Lock the rear carrier system Swivel the left clamping lever ( 1 ) back first, followed by the right clamping lever ( 2 ) until they stop. Both clamping levers must point backwards, otherwise safe functionality is not guaranteed. Note Close the tailgate.
Storage 63 Adapting the rear carrier system to a bicycle With the rotary lever on the pedal crank recess, roughly adapt the adjustable pedal crank unit to the protrusion of the pedal crank. If the bicycle has straight pedal cranks, unscrew the pedal crank unit completely (position 5 ).
64 Storage Prepare the bicycle for attachment Note The maximum width for the pedal crank is 38.3 mm and the maximum depth is 14.4 mm. Rotate the left pedal (without a chain cog) vertically downwards. The pedal on the left pedal crank must be horizontal.
Storage 65 Attach the pedal crank by rotating the attachment screw on the pedal crank mount. Place the wheel recesses such that the bicycle is more or less horizontal. Here, the distance between the pedals and the tailgate should be at least 5 cm. Both bicycle tyres must be in the wheel recesses.
66 Storage Secure both bicycle wheels to the wheel recesses using strap retainers. Check the bicycle to make sure it is secure. Caution Ensure gap between bicycle and vehicle is at least 5 cm.
Storage 67 Retracting the rear carrier system Push the pedal crank mounts into the pedal crank recess as shown in the illustration. Insert the strap retainer and pull tightly downwards as far as possible. Press release lever and slide in wheel recesses all the way as far as they will go.
68 Storage Swivel first the right clamping lever ( 1 ) forwards, followed by the left clamping lever ( 2 ), until they can be engaged in their respective recesses. Push the clamping lever down and pull both lamp supports out of the recesses. Fold in the bulb holders on the backs of the tail lamps.
Storage 69 Raise the release lever and hold. Lift the system slightly and push it into the bumper until it engages. Release lever must return to original position. 9 Warning If the system cannot be correctly engaged, please seek the assistance of a workshop.
70 Storage Removing the cover Open load compartment cover. Pull socket on either side of cover towards centre of vehicle, lift and remove cover from the side guides. Fit in reverse order. Rear floor storage cover To access the rear floor storage compartment, pull floor cover handle upwards.
Storage 71 Where present, hang the hook to the upper part of the tailgate opening. Caution Only use the hook for hanging up the rear floor cover and the height adjustable cover. Caution Do not allow objects to protrude above the top of the rear floor storage compartment, to avoid damage to the storage area and the load compartment floor.
72 Storage Roof rack system Roof rack For safety reasons and to avoid damage to the roof, the vehicle approved roof rack system is recommended. For further information contact a workshop.
Storage 73 To calculate the EC kerb weight, enter the data for your vehicle in the Weights table at the front of this manual. The EC kerb weight includes weights for the driver (68 kg), luggage (7 kg) and all fluids (tank 90 % full). Optional equipment and accessories increase the kerb weight.
74 Instruments and controls Instruments and controls Controls ....................................... 74 Warning lights, gauges and indi‐ cators ........................................... 81 Information displays ..................... 93 Vehicle messages .
Instruments and controls 75 Horn Press j . Windscreen wiper/washer Windscreen wiper & = fast % = slow $ = timed interval wiping or automatic wiping with rain sensor § = off For a single wipe when the windscreen wiper is off, press the lever down.
76 Instruments and controls In this mode, wiping frequency is also affected by vehicle speed. As vehicle speed increases, wiping will become more frequent.
Instruments and controls 77 Control indicator G illuminates in the instrument cluster when the washer fluid level is low. Wiper activated lighting With light switch in the AUTO position, when the windscreen wiper is operated for 8 cycles or more the exterior lights illuminate automatically.
78 Instruments and controls 9 Warning The road surface may already be icy even though the display indicates a few degrees above 0 °C. Clock Date and time are shown in the Info-Display. Board-Info-Display 3 93. Graphic-Info-Display, Colour-Info-Display 3 96.
Instruments and controls 79 Deactivate ( Clock Sync.Off ) or activate ( Clock Sync.On ) automatic time synchronisation with the arrow buttons on the Infotainment system. To set date and time manually, select the menu item for time and date setting from the Settings menu and make the desired setting.
80 Instruments and controls 12 Volt power outlets are located beneath the cupholder in the front centre console, in the rear centre console and on the right-hand side of the load compartment. Pull the cap out to use the power outlet, and replace the cap when not in use.
Instruments and controls 81 Warning lights, gauges and indicators Instrument cluster In some versions, the needles of the instruments briefly rotate to the end position when the ignition is switched on. Speedometer Indicates vehicle speed. Odometer The odometer display is located in the centre of the instrument cluster.
82 Instruments and controls Fuel gauge Displays the fuel level in the tank. Control indicator Y illuminates if the level in the tank is low. Refuel immediately 3 147. Never run the tank dry. Erratic fuel supply can cause catalytic converter to overheat 3 130.
Instruments and controls 83 Control indicators on the instrument panel k illuminates red. Front passenger seat belt reminder 3 43. * illuminates yellow. The front passenger airbag is deactivated 3 50. 9 Danger Risk of fatal injury for a child using a child restraint system together with activated front passenger airbag.
84 Instruments and controls Control indicators in the instrument cluster.
Instruments and controls 85 Turn signal O illuminates or flashes green. The relevant control indicator flashes when the turn signal is switched on 3 110. Rapid flashing: failure of a turn signal bulb or the associated fuse or failure of a turn signal light on trailer.
86 Instruments and controls Interrupt your journey immediately. Remove key and check drive belt condition and tensioning before seeking the assistance of a workshop. Malfunction indicator light Z illuminates or flashes yellow. Illuminates when the ignition is switched on and extinguishes shortly after the engine starts.
Instruments and controls 87 Illuminates when engine is running if fluid level for brake hydraulics is too low 3 158. Brake system 3 138. Electrical parking brake m illuminates or flashes red. When the engine is started, m illuminates briefly. If it does not illuminate, seek the assistance of a workshop.
88 Instruments and controls Flashes briefly when the engine is running The system is temporarily disabled. Flashes continuously when the engine is running System fault. Seek the assistance of a workshop immediately. All wheel drive 3 135. Descent control system u illuminates yellow and/or green.
Instruments and controls 89 Flashes The system is actively engaged. Engine output may be reduced and the vehicle may be braked automatically to a small degree. Electronic Stability Control 3 140. Electronic Stability Control off t illuminates yellow. When the ignition is switched on, t illuminates briefly.
90 Instruments and controls Tyre pressure monitoring system w illuminates or flashes yellow. Illuminates Tyre pressure loss. Stop immediately and check tyre pressure. A corresponding message also appears on the Info-Display 3 93. Flashes Fault in system or tyre without pressure sensor mounted (e.
Instruments and controls 91 Based on driving conditions, the interval at which an oil change will be indicated can vary considerably. Change oil within 1000 km. Engine power may be decreased. Once the engine oil has been changed 3 155, the engine oil life monitor needs to be reset.
92 Instruments and controls Brake pedal needs to be depressed to release the electrical parking brake 3 138. Clutch pedal needs to be depressed to restart the engine. Stop-start system 3 126. High beam C illuminates blue. Illuminated when high beam is on and during headlight flash 3 108.
Instruments and controls 93 Anti-theft alarm system a illuminates yellow. Illuminates when alarm system monitoring of the passenger compartment and vehicle inclination has been switched off with button a in the roof lining. Anti-theft alarm system 3 25.
94 Instruments and controls Select using the Infotainment system buttons In the Settings menu, use the OK button to call up the required function. Use the arrow buttons to change settings. In the BC menu, use the OK button to call up the required function.
Instruments and controls 95 ■ Time, setting minutes ■ Date, setting day ■ Date, setting month ■ Date, setting year ■ Ignition logic ■ Language selection ■ Setting units of measure Automatic time synchronisation The RDS (Radio Data System) signal of most VHF transmitters automatically sets the time, identified by } in the display.
96 Instruments and controls Setting units of measure Select the required unit of measurement with the arrow buttons. Graphic-Info-Display, Colour-Info-Display Depending on the vehicle configuration the vehicle has a Graphic-Info-Display or Colour-Info-Display.
Instruments and controls 97 wheel. If there are several warning messages, acknowledge them one at a time. Check control 3 101. Select using the Infotainment system buttons Select a function via the Infotainment system arrow buttons. The menu of the selected function is displayed.
98 Instruments and controls Function areas For each function area there is a main page (Main), which is selected at the top edge of the display: ■ Audio, ■ Navigation, ■ Telephone, ■ Trip computer. See Infotainment system instruction manual for further information.
Instruments and controls 99 Some RDS transmitters do not send a correct time signal. In such cases, switch off automatic time synchronisation and set the time manually. To set date and time manually, select menu item Time, Date from the Settings menu.
100 Instruments and controls Setting units of measure Select menu item Units from the Settings menu. The available units are displayed. Select the desired unit. Selections are indicated by a o in front of the menu item. Adjusting contrast (Graphic-Info-Display) Select menu item Contrast from the Settings menu.
Instruments and controls 101 Vehicle messages Warning chimes When starting the engine or whilst driving Only one warning chime will sound at a time. The warning chime regarding unfastened seat belts has priority over any other warning chime. ■ If seat belt is not fastened.
102 Instruments and controls Steer out of the flow of traffic as quickly as possible without endangering other vehicles. Stop and check the tyres. Mount the spare wheel 3 186, 3 189.
Instruments and controls 103 Average consumption Display of average consumption. The measurement can be reset at any time. Effective consumption Display of the amount of fuel consumed. The measurement can be reset at any time. Average speed Display of average speed.
104 Instruments and controls Interruption of power supply If the power supply has been interrupted or if the battery voltage has dropped too low, the values stored in the trip computer will be lost.
Instruments and controls 105 Instantaneous consumption Display of the instantaneous consumption. Display changes depending on speed: Display in l/h = below 13 km/h Display in l/100 km = above 13 km/h Distance travelled Display of distance travelled. The measurement can be reset at any time.
106 Instruments and controls Stop watch Select menu item Timer from the Board Computer menu. The Timer menu is displayed. To start, select menu item Start . To reset, select menu item Reset . The desired stop watch display can be selected from the Options menu: Driving Time excl.
Lighting 107 Lighting Exterior lighting .......................... 107 Interior lighting ........................... 112 Lighting features ........................ 114 Exterior lighting Light switch Turn light switch: AUTO = Automatic light control: Headlights are switched on and off automatically depending on external lighting conditions.
108 Lighting To ensure automatic light control functions properly, do not cover the light sensor on top of the instrument panel. Driving abroad 3 109. Wiper activated lighting With light switch in the AUTO position, when the windscreen wiper is operated for 8 cycles or more the exterior lights illuminate automatically.
Lighting 109 Vehicles without automatic level control system Turn thumb wheel ? to required position: 0 = front seats occupied 1 = all seats occupied 2 = all seats occupied and load compartment laden .
110 Lighting Turn and lane-change signals lever up = right turn signal lever down = left turn signal If the lever is moved past the resistance point, the turn signal is switched on constantly. When the steering wheel is turned back, the turn signal is automatically deactivated.
Lighting 111 Rear fog lights Operated with the r button. Control indicator r illuminates in the instrument cluster when the rear fog light is switched on. The rear fog light can only be switched on when the ignition is on and the light switch is in position 9 , or the front fog lights are on and the light switch is in position 8 .
112 Lighting Interior lighting Instrument panel illumination control Brightness of the following lights can be adjusted when the exterior lights are on: ■ Instrument panel illumination ■ Info-Display ■ Illuminated switches and operation elements.
Lighting 113 Courtesy lights can be turned off immediately by pressing button K . Ignition switch illumination Illuminates when you open a door. Switch off immediately by pressing button K in the roof lining. Glovebox illumination Illuminates when the glovebox is opened.
114 Lighting Rear reading lights Left and right rear reading lights are individually operable. Press to activate and deactivate. Sunvisor lights Illuminates when the vanity mirror cover is opened 3 33.
Lighting 115 Battery discharge protection To prevent the battery from becoming discharged, the exterior lights turn off automatically 10 minutes after the ignition is switched off.
116 Climate control Climate control Climate control systems ............. 116 Air vents ..................................... 121 Maintenance .........
Climate control 117 Demisting and defrosting ■ Set the air distribution switch to l or J ■ Set temperature control to warmest level ■ Set fan to highest level ■ Close centre air vents ■ Open side air vents and direct them towards the door windows Heated rear window Ü 3 32.
118 Climate control directed to it. If windscreen mists up from outside, activate windscreen wiper and deactivate l . Maximum cooling Briefly open the windows and sunroof so that hot air can disperse quickly. ■ Press button n to activate air conditioning.
Climate control 119 ■ Fan speed ■ Temperature on front passenger side AUTO = Automatic mode t = Automatic air recirculation V = Demisting and defrosting Cooling A/C , Air recirculation 4 3 117.
120 Climate control Climate control system settings can be changed by pressing button A/C or by adjusting the fan speed or air distribution switch. Changing a setting will deactivate Automatic mode. To return to Automatic mode: Press AUTO button. Cooling A/C 3 117.
Climate control 121 To switch off window demisting and defrosting, press button V again, press AUTO button, adjust fan speed or air distribution switch. Air vents Adjustable air vents At least one air vent must be open while the cooling A/C is on. To open and close the vents, turn the horizontal adjuster wheel to the left or right.
122 Climate control Fixed air vents Additional air vents are located beneath the windscreen, door windows and in the front and rear foot wells. The area underneath the front seats must be kept clear, to allow air flow to the rear passenger foot well.
Climate control 123 ■ Cleaning of condenser and evaporator drainage ■ Performance check.
124 Driving and operating Driving and operating Driving hints ............................... 124 Starting and operating ............... 125 Engine exhaust .......................... 129 Automatic transmission .............. 131 Manual transmission ..
Driving and operating 125 Starting and operating New vehicle running-in Do not brake unnecessarily hard for the first few journeys. During the first drive, smoke may occur because of wax and oil evaporating off the exhaust system. Park the vehicle in the open for a while after the first drive and avoid inhaling the fumes.
126 Driving and operating Before restarting or to switch off the engine, turn key back to LOCK . Start attempts should not last longer than 15 seconds. If engine does not start, wait 10 seconds before repeating starting procedure. The increased engine speed automatically returns to normal idling speed as the engine temperature rises.
Driving and operating 127 Deactivation Deactivate the stop-start system manually by pressing the eco button. The deactivation is indicated when the LED in the button extinguishes.
128 Driving and operating ■ the self-cleaning function of the diesel particle filter is not active ■ the vehicle has moved since the last Autostop Otherwise an Autostop will be inhibited. Certain settings of the climate control system may inhibit an Autostop.
Driving and operating 129 ■ Switch off the engine and turn the ignition key to position LOCK , push key into ignition switch and remove. Turn the steering wheel until the steering wheel lock is felt to engage. For vehicles with automatic transmission, depress foot brake and shift into P before pushing key into ignition switch and removing.
130 Driving and operating The filter is cleaned by periodically burning off the soot particles at high temperature. This process takes place automatically under set driving conditions and may take more than 15 minutes. Autostop is not available and fuel consumption may be higher during this period.
Driving and operating 131 Caution Fuel grades other than those listed on pages 3 145, 3 205 could damage the catalytic converter or electronic components. Unburnt petrol will overheat and damage the catalytic converter. Therefore avoid excessive use of the starter, running the fuel tank dry and starting the engine by pushing or towing.
132 Driving and operating The selector lever is locked in position P and N and can only be moved when the ignition is on and the foot brake is applied. To engage P or R , push the release button. Never shift to P or R while the vehicle is moving. The engine can only be started with lever in position P or N .
Driving and operating 133 transmission will automatically shift to a lower gear, even in manual mode, to prevent the engine from stalling. If a higher gear is selected when vehicle speed is too low, or a lower gear when vehicle speed is too high, the shift is not executed.
134 Driving and operating Deactivation Fuel economy mode is switched off by pressing button s again; control indicator s extinguishes in the instrument cluster. Fault In the event of a fault in the automatic transmission, control indicator Z illuminates in the instrument cluster 3 86.
Driving and operating 135 Manual transmission To engage reverse, with the vehicle stationary, wait 3 seconds after depressing clutch pedal and engage the gear. If the gear does not engage, set the lever to neutral, release the clutch pedal and depress again; then repeat gear selection.
136 Driving and operating Ensure tyres (including the spare) are inflated to the correct pressure 3 210 and are suitable for the prevailing road conditions. For optimum system performance, the vehicle's tyres should not have varying degrees of wear.
Driving and operating 137 operations for wading , involving checks for water contamination, at the earliest opportunity. Service checks after wading Check for the ingress of water into the following: .
138 Driving and operating Brakes The brake system comprises two independent brake circuits. If a brake circuit fails, the vehicle can still be braked using the other brake circuit. However, braking effect is achieved only when the brake pedal is depressed firmly.
Driving and operating 139 Applying when vehicle is stationary Pull switch m , the electrical parking brake operates automatically with adequate force. For maximum force, e.g. parking with a trailer or on inclines, pull switch m twice. The electrical parking brake can always be activated, even if the ignition is off.
140 Driving and operating movement. Seek the assistance of a workshop to have the cause of the fault remedied. Brake assist If the brake pedal is depressed quickly and forcefully, maximum brake force is automatically applied (full braking). Maintain steady pressure on the brake pedal for as long as full braking is required.
Driving and operating 141 Switch off ESC function, to allow engine rpm to increase, by pressing button t briefly. Control indicator t illuminates in the instrument cluster. ESC is reactivated by pressing button t again. The control indicator extinguishes.
142 Driving and operating Fault The yellow control indicator u flashes to indicate that the system is not ready for conditions to operate, due to the high temperature (approx. 350 - 400 °C) of friction material, through severe or repeated braking. It will extinguish when the temperature drops below 350 °C.
Driving and operating 143 Do not use the cruise control if it is not advisable to maintain a constant speed. With automatic transmission, only activate cruise control in automatic mode. Control indicator m 3 92. Activation Press the e button; control indicator m illuminates yellow in the instrument cluster.
144 Driving and operating Parking assist The parking assist system makes parking easier by measuring the distance between the vehicle and obstacles to the front and rear, and giving acoustic signals. It is the driver, however, who bears full responsibility for the parking manoeuvre.
Driving and operating 145 If the acoustic signal sounds 3 times continuously when there are no obstacles near the front or rear bumper, there is a fault in the system.
146 Driving and operating Caution Use of fuel that does not comply to EN 228 or E DIN 51626-1 or equivalent can lead to deposits or engine damage and may affect your warranty. Caution Use of fuel with too low an octane rating could lead to uncontrolled combustion and engine damage.
Driving and operating 147 Do not use marine diesel oils, heating oils, Aquazole and similar diesel- water emulsions. Diesel fuels must not be diluted with fuels for petrol engines. Refuelling 9 Danger Before refuelling, switch off engine and any external heaters with combustion chambers.
148 Driving and operating Fuel consumption - CO 2 - Emissions The fuel consumption (combined) of the model Opel Antara is within a range of 10.9 to 6.3 l/100 km.
Driving and operating 149 If no eye is available, loop cable around coupling ball bar. Ensure cable is crossed under the vertical coupling socket to ensure the trailer nose cannot drop to the ground if it becomes separated from the trailer hitch. Do not allow the cable to drag along the ground and always allow enough slack to permit full turning.
150 Driving and operating especially in the case of heavy trailers. The vertical coupling load should never fall below 25 kg. When measuring the vertical coupling load, ensure the drawbar of the loaded trailer is at the same height as it will be when the trailer is coupled with the towing vehicle loaded.
Driving and operating 151 Inserting the coupling ball bar Insert the coupling ball bar into the coupling housing and push firmly downwards until the coupling ball bar audibly engages.
152 Driving and operating Unlock coupling ball bar and remove key. Push lever to the left, towards the coupling ball bar and turn it downwards. Pull coupling ball bar out of coupling housing. Remove any rust or dirt from area around the coupling housing and coupling ball bar connection before inserting sealing plug in the hole.
Vehicle care 153 Vehicle care General Information ................... 153 Vehicle checks ........................... 154 Bulb replacement ....................... 162 Electrical system ........................ 168 Vehicle tools ........................
154 Vehicle care ■ Open the bonnet, close all doors and lock the vehicle. ■ Disconnect the clamp from the negative terminal of the vehicle battery.
Vehicle care 155 Bonnet Opening Pull the release lever and return it to its original position. Locate the safety catch, found slightly left of centre on the underside of the bonnet, push the catch upwards and lift the bonnet gently. The bonnet is held open automatically.
156 Vehicle care Different dipsticks are used depending on engine variant. When the engine oil level has dropped to the MIN mark, top up engine oil. We recommend the use of the same grade of engine oil that was used at the last oil change. The engine oil level must not exceed the MAX mark on the dipstick.
Vehicle care 157 If the cooling system is cold, the coolant level should be between the MIN and MAX marks. Top up if the level is low. 9 Warning Allow the engine to cool before opening the cap. Carefully open the cap, relieving the pressure slowly. To top up use a 1:1 mixture of released coolant concentrate mixed with clean tap water.
158 Vehicle care Washer fluid Fill with clean water mixed with a suitable quantity of washer fluid which contains antifreeze. For the correct mixing ratio refer to the washer fluid container. Caution Only washer fluid with a sufficient antifreeze concentration provides protection at low temperatures or a sudden drop in temperature.
Vehicle care 159 Caution Only use high-performance brake fluid approved for the vehicle. Brake fluid 3 198. Brake fluid level control indicator R 3 86. Clutch fluid 9 Warning Clutch fluid is poisonous and corrosive. Avoid contact with eyes, skin, fabrics and painted surfaces.
160 Vehicle care assistance of a workshop regarding technical possibilities, such as fitting a more powerful battery. Ensure the ignition is switched off before reconnecting the vehicle battery. Then perform the following actions: 1. Set date and time in the information display 3 78.
Vehicle care 161 Warning label Meaning of symbols: ■ No sparks, naked flames or smoking. ■ Always shield eyes. Explosive gases can cause blindness or injury. ■ Keep the vehicle battery out of reach of children. ■ The vehicle battery contains sulfuric acid which could cause blindness or serious burn injuries.
162 Vehicle care Wiper blade replacement Wiper blades on the windscreen Lift wiper arm, press and hold retaining clip and detach wiper blade. Attach the wiper blade slightly angled to the wiper arm and push until it engages. Lower wiper arm carefully.
Vehicle care 163 Halogen headlights Halogen headlights A can be identified from Xenon headlights B by the different lens layout. Low and high beam Halogen headlights have separate systems for high beam 1 (inner bulbs) and low beam 2 (outer bulbs). 1. Remove headlamp assembly 3 162.
164 Vehicle care 5. Reinstall bulb holder in lamp assembly by rotating it clockwise. 6. Reinstall headlamp assembly. Sidelights 1. Remove headlamp assembly 3 162. 2. Remove headlamp cap and withdraw bulb holder (located next to high beam bulb) from lamp assembly.
Vehicle care 165 3. Press and rotate bulb anticlockwise to remove it from bulb holder. 4. Insert new bulb into bulb holder by pressing and rotating it clockwise. 5. Reinstall bulb holder in lamp assembly by rotating it clockwise. 6. Reinstall headlamp assembly.
166 Vehicle care Tail lights Rear brake, tail, turn signal, reverse and fog tail light 1. Open the tailgate and remove 2 screws and lamp assembly. 2. Remove bulb holder by rotating it anticlockwise. 3. Remove bulb from bulb holder by pressing the bulb in and rotating it anticlockwise.
Vehicle care 167 Centre high-mounted brake light Have bulbs replaced by a workshop. Number plate light 1. Remove 4 screws (arrowed) and remove lamp covers. 2. Remove bulb holder from lamp assembly by rotating it anticlockwise. 3. Pull bulb straight out of bulb holder.
168 Vehicle care Load compartment light 1. Using a suitable screwdriver, remove lens from lamp assembly. 2. Remove bulb. 3. Insert new bulb. 4. Reinstall lens to lamp assembly. Glovebox light Have bulbs replaced by a workshop. Instrument panel illumination Have bulbs replaced by a workshop.
Vehicle care 169 Fuse extractor A fuse extractor may be located in the engine compartment fuse box. Place the fuse extractor on the various types of fuse from the top or side, and withdraw fuse. Engine compartment fuse box The fuse box is located next to the coolant reservoir in the engine compartment.
170 Vehicle care.
Vehicle care 171 Fuse Circuit ABS Anti-lock Brake System A/C Climate control, air conditioning system BATT1 Instrument panel fuse box BATT2 Instrument panel fuse box BATT3 Instrument panel fuse box BC.
172 Vehicle care After changing of defective fuses close the fuse box cover and press until it engages. If the fuse box cover is not closed correctly, malfunctions may occur.
Vehicle care 173.
174 Vehicle care Fuse Circuit AMP Amplifier APO JACK (CONSOLE) Power outlet (centre console) APO JACK (REAR CARGO) Power outlet (load compart‐ ment) AWD/VENT All-wheel drive, ventilation BCM (CTSY) .
Vehicle care 175 Fuse Circuit RUN 2 Power battery key on run RUN/CRNK Run crank SDM (BATT) Safety Diag‐ nosis Module (Battery) SDM (IGN 1) Safety Diag‐ nosis Module (Ignition) SPARE - S/ROOF Sunro.
176 Vehicle care To remove the jack and vehicle tools, open the tailgate. Push both levers on the floor cover towards the handle and pull up the cover by the handle. Where present, hang the hook to the upper part of the tailgate opening. Remove wing bolt from the jack by rotating it anticlockwise and remove the jack and wheel wrench bag.
Vehicle care 177 To remove the tyre repair kit, open the tailgate and pull the floor cover handle upwards 3 70. Caution Do not allow objects to protrude above the top of the rear floor storage compartment, to avoid damage to the storage area and the load compartment floor.
178 Vehicle care V = up to 240 km/h W = up to 270 km/h Tyre pressure Check the pressure of cold tyres at least every 14 days and before any long journey. Do not forget the spare wheel. This also applies to vehicles with tyre pressure monitoring system.
Vehicle care 179 Note In countries where the tyre pressure monitoring system is legally required, the use of wheels without pressure sensors will invalidate the vehicle type approval. The TPMS sensors monitor the air pressure in the tyres and transmit tyre pressure readings to a receiver located in the vehicle.
180 Vehicle care For example, the following messages can be displayed: A graphic indicating the left rear tyre is shown together with the current tyre pressure; slight pressure deviation. Reduce speed. Check tyre pressure at next opportunity with an appropriate gauge and correct if necessary.
Vehicle care 181 TPMS sensor matching process Each TPMS sensor has a unique identification code. The identification code must be matched to a new tyre/ wheel position after rotating the tyres or replacing one or more of the TPMS sensors.
182 Vehicle care Tread depth Check tread depth at regular intervals. Tyres should be replaced for safety reasons at a tread depth of 2-3 mm (4 mm for winter tyres). For safety reasons it is recommended that the tread depth of the tyres on one axle should not vary by more than 2 mm.
Vehicle care 183 9 Warning Use of unsuitable tyres or wheel covers could lead to sudden pressure loss and thereby accidents. Tyre chains Tyre chains are only permitted on the front wheels. They must be fitted to the tyres symmetrically in order to achieve a concentric fit.
184 Vehicle care Pull the floor cover handle upwards 3 70. Vehicle tools 3 175. Caution Do not allow objects to protrude above the top of the rear floor storage compartment, to avoid damage to the storage area and the load compartment floor. 1. Release the sealant filler hose 1 and the power plug 2 .
Vehicle care 185 is obtained, switch off the compressor. If the prescribed tyre pressure is not obtained within 10 minutes, remove the tyre repair kit. Move the vehicle one tyre rotation. Reattach the tyre repair kit and continue the filling procedure for 10 minutes.
186 Vehicle care 13. Turn the selector switch clockwise to the air only position. Switch on the compressor to inflate the tyre with air only. Note The driving characteristic of the repaired tyre is severely affected, therefore have this tyre replaced.
Vehicle care 187 ■ Do not raise the vehicle more than is necessary to change a wheel. ■ No people or animals may be in the vehicle when it is jacked-up. ■ Never crawl under a jacked-up vehicle. ■ Do not start the engine when it is raised on the jack.
188 Vehicle care 5. Attach wheel wrench to eye of threaded rod and rotate wrench clockwise to raise vehicle. If this is not the case, carefully lower the vehicle immediately and reposition the jack. Raise the vehicle until the wheel is just clear of the ground.
Vehicle care 189 Front arm position of the lifting platform centrically under the recess of the sill. Spare wheel Temporary spare wheel Some vehicles are equipped with a tyre repair kit instead of a spare wheel. The temporary spare wheel is designed for use on your vehicle only.
190 Vehicle care Only mount one temporary spare wheel. Do not drive faster than 80 km/h. Take curves slowly. Do not use for a long period of time. When the temporary spare wheel is fitted, do not take the vehicle through an automatic vehicle wash with guide rails.
Vehicle care 191 ■ A discharged battery can already freeze at a temperature of 0 °C. Defrost the frozen battery before connecting jump leads. ■ Wear eye protection and protective clothing when handling a battery. ■ Use a booster battery with the same voltage (12 Volts).
192 Vehicle care 4. Switch on electrical consumers (e.g. headlights, heated rear window) of the vehicle receiving the jump start. 5. Operate discharged vehicle for approx. 20 minutes to allow for adequate battery recharging. 6. Reverse above sequence exactly when removing leads.
Vehicle care 193 Turn key to ignition switch position ACC and release the electrical parking brake before towing the vehicle. Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. When the engine is not running, considerably more force is needed to brake and steer.
194 Vehicle care The towing eye must only be used for towing and not for recovering a vehicle. Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. To prevent damage, do not take up slack in the tow rope too quickly.
Vehicle care 195 When cleaning with a high-pressure jet cleaner, ensure a minimum distance of 30 cm when working around the tailgate to prevent unintended unlocking. Thoroughly rinse and leather-off the vehicle. Rinse leather frequently. Use separate leathers for painted and glass surfaces: remnants of wax on the windows will impair vision.
196 Vehicle care After the underbody is washed, check the underbody and have it waxed if necessary. Bitumen/rubber materials could damage the PVC coating. Have underbody work carried out by a workshop. Before and after winter, wash the underbody and have the protective wax coating checked.
Service and maintenance 197 Service and maintenance General information ................... 197 Recommended fluids, lubricants and parts ..............
198 Service and maintenance Confirmations Confirmation of service is recorded in the Service and Warranty Booklet. The date and mileage is completed with the stamp and signature of the servicing workshop.
Service and maintenance 199 Select the appropriate engine oil based on its quality and on the minimum ambient temperature 3 202. Additional engine oil additives The use of additional engine oil additives could cause damage and invalidate the warranty.
200 Technical data Technical data Vehicle identification .................. 200 Vehicle data ............................... 202 Vehicle identification Vehicle Identification Number The Vehicle Identification Number is visible through the windscreen.
Technical data 201 Identification plate The identification label is located on the front left door frame. Information on identification label: 1 = Manufacturer 2 = Type approval number 3 = Vehicle Ide.
202 Technical data Vehicle data Recommended fluids and lubricants European service schedule Required engine oil quality All European countries (except Belarus, Moldova, Russia, Turkey) Only Israel Eng.
Technical data 203 International service schedule Required engine oil quality All countries outside Europe except Israel Only Belarus, Moldova, Russia, Turkey Engine oil quality Petrol engines (includ.
204 Technical data All countries outside Europe except Israel Only Belarus, Moldova, Russia, Turkey Engine oil quality Petrol engines (including E85) Diesel engines Petrol engines (including E85) Dies.
Technical data 205 Engine data Sales designation 2.4 3.0 V6 2.2 CDTI 2.2 CDTI Engine identifier code A 24 XF A 30 XF A 22 DM A 22 DMH Number of cylinders 4 6 4 4 Piston displacement [cm 3 ] 2384 2997 .
206 Technical data Performance All-wheel drive Engine A 24 XF A 30 XF A 22 DM A 22 DMH Maximum speed 4) [km/h] Manual transmission 186 – 188 200 Automatic transmission 175 198 182 191 4) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload.
Technical data 207 Vehicle weight Kerb weight, basic model without any optional equipment Manual transmission / Automatic transmission. Engine All-wheel drive Front-wheel drive A 24 XF 1825-1885 / 184.
208 Technical data Rear 1576 Turning circle diameter, wall to wall [m] 12.78 Turning circle diameter, kerb to kerb [m] 11.87 Maximum wading depth [mm] (at 5 km/h) 450 Approach angle 20° Ramp angle 18.
Technical data 209 Capacities Engine oil Engine A 24 XF A 30 XF A 22 DM A 22 DMH including filter [l] 4.7 5.7 5.6 5.6 between MIN and MAX [l] 1.0 1.0 1.
210 Technical data Tyre pressures Up to full load Up to full load ECO Trailer towing Engine Tyres front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) All 215/70 R 16 5) , 235/65 R 17, 235/55 R 18, 235/50 R 19 240/2.
Customer information 211 Customer information Customer information ................ 211 Vehicle data recording and pri‐ vacy ........................................... 213 Customer information Declaration of conformity Transmission systems This vehicle has systems that transmit and/or receive radio waves subject to Directive 1999/5/EC.
212 Customer information Jack.
Customer information 213 Vehicle data recording and privacy Event data recorders Data storage modules in the vehicle A large number of electronic components of your vehicle contain data storage modules temporarily or permanently storing technical data about the condition of the vehicle, events and errors.
214 Customer information Radio Frequency Identification (RFID) RFID technology is used in some vehicles for functions such as tyre pressure monitoring and ignition system security.
Customer information 215.
216 Index A Accessories and vehicle modifications .......................... 153 Accessory sockets ........................ 79 Active head restraints ............. 35, 36 Adjustable air vents ................... 121 Airbag and belt tensioners ........
.
218 Fuel consumption - CO 2 - Emissions ............................... 148 Fuel economy mode ..................... 91 Fuel filler cap ................................ 86 Fuel for diesel engines .............. 146 Fuel for petrol engines .............
219 N New vehicle running-in .............. 125 Number plate light ..................... 167 O Object detection systems ........... 144 Octane rating .............................. 205 Odometer ..................................... 81 Oil ............
デバイスOpel Antara (2015)の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Opel Antara (2015)をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOpel Antara (2015)の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Opel Antara (2015)の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Opel Antara (2015)で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Opel Antara (2015)を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOpel Antara (2015)の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Opel Antara (2015)に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOpel Antara (2015)デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
