ParaBodyメーカー777の使用説明書/サービス説明書
ページ先へ移動 of 28
1 777 GYM SYSTEM 1 CLASS H PAR T # 7148201 REV . A V ersion: 777102 Revision: 07/26/01 USER’S GUIDE W ARNING: Read and follow all directions for each step to insure proper assembly of this product.
THERE IS A RISK ASSU MED BY IND IVIDUALS W HO USE T HI S TYPE OF EQUIPMENT. TO MINIMIZE RISK F OLLOW THESE RULE S ! 1. Before u sing, read al l the w arnings and in structions on the use of this mach ine. Use only for in tended exercise. DO NOT mo dify the m achine.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the ParaBody 777 Gym System. Please read these instructions thoroughly and keep them for future reference.
Minimum Required Usable S p ace Length = 90 inches (229 cm) 7’ 6” Width = 103 inches (262 cm) 8’ 7” Height = 84 inches (213.5 cm) 7” 1 Square = 1’ X 1’ 4 Length = 102 inches (259 cm) 8.
3 P AR TS LIST 5 PA R T # 70077 70076 70058 70014 70015 70017 70019 70056 70067 69408 69885 69954 69957 71552 71553 69947 6194601 6816501 7016902 7016901 6939202 6382301 69537 3221702 6978101 7095701 .
FIGURE 1 6 STEP 1: • LOOSEL Y assemble two BASE PLA TES (11) to the BASE (1) and the UPRIGHT (2) using four 3/8 X 3-3/4” BOL TS (57) and four 3/8” LOCK NUTS (63).
7 FIGURE 3 STEP 3: FIGURE 2 • Insert two WEIGHT PLA TE BUSHINGS (22) into each of the fifteen WEIGHT PLA TES (21) as shown in FIGURE 2. STEP 2: • Slide the WEIGHT PLA TE SHAFT (26) thru the hole in the HEAD PLA TE(23), and lock in place using one E-RING (24) as shown in FIGURE 3.
FIGURE 4 STEP 4: 8 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Insert two GUIDE RODS (18) into the BASE (1) as shown on FIGURE 4. (NOTE: If the 777 SHROUD OPTION was pur - chased, place the GUIDE RODS (18) through the BOTTOM SHROUD BRACKET (found in SHROUD OPTION box) and into the BASE (1) as shown in FIGURE 4.
9 STEP 5: • Swing the GUIDE RODS (18) into the guide rod bushings in each of the RIGHT and LEFT BOOM PLA TES (14 & 15) as shown in FIGURE 5. • LOOSEL Y assemble the RIGHT and LEFT BOOM PLA TES (14 & 15) to the UPRIGHT (2) using three 3/8 X 3-3/4” BOL TS (57) and three 3/8” LOCK NUTS (63).
10 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 7: STEP 8: • SECUREL Y assemble one SEA T P AD (16) to the SEA T ADJUST (3) using two 3/8 X 2-3/4” BOL TS (55) and two 3/8” W ASHERS (64).
11 FIGURE 9 STEP 9: 40 2 3 43 42 • Securely assemble one SPRING PIN ASSEMBL Y (40) and one 3 PRONG KNOB (43) to the FRONT UPRIGHT (2) as shown. • Apply eight P ARAGLIDES (42) to the INSIDE of the tube on the UPRIGHT (2) and on the OUTSIDE of the SEA T ADJUST (3) as shown.
12 STEP 1 1: • Assemble two V -PULLEY PLA TES (12) and two 4-1/2” V -GROOVE PULLEYS (39) to the UPRIGHT (2) using two 3/8 X 2-3/4” BOL TS (55) . See FIGURE 1 1.
13 STEP 13: STEP 14: FIGURE 13 • Assemble one 4-1/2” PULLEY (38) to the BOOM PLA TES (14 & 15) using one 3/8 X 3-3/4” BOL T (57), two 3/8 X 1” SP ACERS (51) and one 3/8” LOCK NUT (63).
STEP 15: FIGURE 15 70 37 29 51 3/8 X 4-1/4” 68 2 63 • Assemble one 3-1/2” PULLEY (37) to the BOOM PLA TES (14 & 15) using one 3/8 X 4-1/4” BOL T (68), two 3/8” SAE W ASHERS (69), two GUIDE CABLES (71), two 3/8 X 1” SP ACERS (51) and one 3/8” LOCK NUT (63).
15 STEP 16: FIGURE 16 37 9 63 3/8 X 1-3/4” 53 • Route the BOOM CABLE (32) over the V -GROOVE PULLEY (39) and the 3-1/2” PULLEY (37) on the LEFT BOOM PLA TE (15) and over the 3-1/2” PULLEY (37) on the RIGHT BOOM PLA TE (14) and over the V -GROOVE PULLEY (39) as shown in STEP 16.
• Assemble the SHOR T CABLE and the turnbuckle to each GUIDE CABLE (71) as shown in FIGURE 17. FIGURE 17 • CAREFULL Y slide the GUIDE BRACKET (70) through the GUIDE CABLES (71) as shown in FIGURE 17.
17 STEP 18: FIGURE 18 • Securely assemble the ball end of the LEG CABLE (30) and one 3-1/2” PULLEY (37) to the LEG PEDEST AL (8) using two 3/8 X 3-3/4” BOL TS (57), two 3/8” X 1-1/16” FLANGE SP ACERS (49), two 3/8” W ASHERS (64), and two 3/8” LOCKNUTS (63).
18 STEP 19: STEP 20: FIGURE 19 FIGURE 20 • Screw the threaded end of the LEG CABLE (30) into the end of the PULLEY BRACKET (9). See FIGURE 20. • Assemble one 3-1/2” PULLEY (37) to the PULLEY PLA TES (10) using one 3/8 X 1- 3/4” BOL T (53) and one 3/8” LOCK NUT (63) as shown in FIGURE 19.
19 STEP 21: FIGURE 21 • Assemble one V -PULLEY (39) to the LEFT ARM SUPPOR T (5) using one 3/8 X 2-3/4” BOL T (55) and one 3/8” LOCK NUT (63). See FIGURE 21. (Note: Loop the ARM CABLE around the PULLEY prior to assembling the LEFT ARM SUPPOR T .
20 STEP 23: FIGURE 23 STEP 22: FIGURE 22 • Assemble two 3-1/2” PULLEYS (37) to the BASE PLA TES (1 1) using two 3/8 X 3-3/4” BOL TS (57), one 3/8 X 1” SP ACER (51) and two 3/8” LOCK NUTS (63). See FIGURE 22. (Note: Loop the ARM CABLE (31) around the PULLEYS prior to assem- bling the PULLEYS.
21 STEP 24: FIGURE 24 38 39 6 31 63 3/8 X 2-3/4” 55 4 • Assemble one V -PULLEY (39) to the RIGHT ARM SUPPOR T (4) using using one 3/8 X 2-3/4” BOL T (55) and one 3/8” LOCK NUT (63). See FIGURE 24. (Note: Loop the ARM CABLE around the PULLEY prior to assembling the RIGHT ARM SUPPOR T .
22 STEP 25: FIGURE 25 • SECUREL Y tighten all loose frame connections as shown in FIGURE 25! TIGHTEN! TIGHTEN! TIGHTEN! TIGHTEN! 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 TIGHTEN! TIGHTEN!.
23 STEP 26: FIGURE 26 2 16 64 • SECUREL Y assemble one SEA T P AD (16) to the UPRIGHT (2) using two 3/8 X 2-3/4” BOL TS (55) and two 3/8” W ASHERS (64). See FIGURE 26. • Assemble two ROLLER P ADS (17) to the LEG PEDEST AL (8) using one 3/4 X 17” TUBE (52) and two 3/4” ST ARLOCK COLLARS (44) as shown in FIGURE 27.
24 • Assemble two 14-1/2” SEWN HANDLES (19) to the ARM CABLE (31) using two SNAP LINKS (41) as shown in FIGURE 28. STEP 28: FIGURE 28 32 41 20 31 41 19 • Assemble two 7-1/2” SEWN HANDLES (20) to the BOOM CABLE (32) using two SNAP LINKS (41) as shown in FIGURE 28.
25 FIGURE 29 ADJUSTMENT • Adjustments can be made in the above locations to set the correct amount of tension in the cables. ADJUSTMENT ADJUSTMENT STEP 29: 9 23 9 • If upon completion of assembly .
MAINTENANCE MODEL #________________________ SERIAL #_________________________ DA TE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 26 * W e recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water .
27 NOTES: LIMITED W ARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The W arranty terms apply to IN HOME USE ONL Y . 1. LIMITED W ARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repair ed or replaced by ParaBody .
INTERNA TIONAL OFFICES Life Fitness Atlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 Life Fitness Japan 8/F , Nippon Brunswick Building 5-27-7 Sendagaya Shibuya-Ku, T okyo 151-0051 Japan Phone: 81 (3) 3359-4309 Fax: 81 (3) 3359-4307 Life Fitness (UK) Ltd.
デバイスParaBody 777の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
ParaBody 777をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはParaBody 777の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ParaBody 777の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ParaBody 777で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ParaBody 777を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はParaBody 777の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ParaBody 777に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちParaBody 777デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
