ParaBodyメーカー880の使用説明書/サービス説明書
ページ先へ移動 of 26
1 881 LEG PRESS ADAPTER KIT FOR 880 GYM SYSTEM CLASS H PAR T # 7168701 REV . C V ersion: 881 102 Revision: 3/08/02 USER’S GUIDE W ARNING: Read and follow all directions for each step to insure proper assembly of this product.
THERE IS A RISK ASSU MED BY IND IVIDUAL S W HO USE T HIS TYPE OF EQUIPMENT. TO MINIMIZE RISK F OLLOW THESE RULES ! 1. Before u sing, read al l the w arnings and in structi ons on the use of this mach ine. Use only for intended exercise. DO NOT mo dify th e machine.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the ParaBody 881 LEG PRESS ADAPTER KIT . Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
PARTS LIST 4 PA R T # 7160008 7156001 7156102 31 16201 3102501 3102802 3102924 3102922 3102905 3102935 KEY 1 2 3 4 5 6 7 8 9 10 QTY 1 1 1 9 7 8 4 2 3 5 PA R T # 6533501 3102807 6122701 6480301 7242408.
STEP 1: FIGURE 1 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • REMOVE the LA T CABLE, THREADED HOUSING , 3/8 X 3-3/4” BOL T , two 3/8 X 1” SP ACERS and one 3/8” LOCK NUT from the 880 GYM SYSTEM. See FIGURE 1. Save the LA T CABLE if you ever plan to purchase the SECOND ST ACK OPTION.
6 STEP 2: FIGURE 2 • Remove the PEC ST A TION P AD from the FRAME, then discard the two 3/8 X 2-3/4” BOL TS. See FIGURE 2. 3/8 X 2-3/4” STEP 3: FIGURE 3 • SECUREL Y assemble the PULLEY BRACKET (15) and the PEC ST A TION P AD to the FRAME using two 3/8 X 3” BOL TS (18).
STEP 4: FIGURE 4 7 • Remove the two 3/8 X 4” BOL TS, four 3/8” W ASHERS and two 3/8” LOCK NUTS from the REAR UPRIGHT as shown in FIGURE 4. Discard the 3/8 X 4” BOL TS.
STEP 6: FIGURE 6 • Route the SHOR T LEG CABLE (2) through the FRAME and BOOM BRACKET as shown in FIGURE 4. (NOTE: Remove pulleys for ease of installation.
STEP 7: FIGURE 7 • Route the SHOR T LEG PRESS CABLE (2) through the PULLEY PLA TES as shown in FIGURE 7. 3/8 X 1-3/4” 7 • Route the SHOR T LEG PRESS CABLE (2) around one 3-1/2” PULLEY (4) and assemble the PULLEY to the PULLEY BRACKET (15) using one 3/8 X 1-3/4” BOL T (7) and one previously removed 3/8” LOCK NUT .
STEP 8: FIGURE 8 • Remove the 3-1/2” PULLEY , one 3/8 X 3-3/4” BOL T , two 3/8 X 1” SP ACERS and one 3/8” LOCK NUT from the BASE PLA TES as shown in FIGURE 8.
11 STEP 10: FIGURE 10 • SECUREL Y assemble the LEG PRESS ADAPTER (1) to the BASE FRAME using one 3/8 X 3-3/4” BOL T (9), one previously removed 3/8 X 3-3/4” BOL T , two 3/8” W ASHERS (5), two previously removed 3/8” W ASHERS and two 3/8” LOCK NUTS (6) as shown in FIGURE 10.
12 FIGURE 12 STEP 12: • Carefully route the SHOR T LEG PRESS CABLE (2) around one 3-1/2” PULLEY (4) and SECUREL Y assemble the 3-1/2” PULLEY (4) to the BRACKET (from 100 LEG PRESS kit) using one 3/8 X 1-3/4” BOL T (7), one 3/8” W ASHER (5), one CABLE CLIP (1 1) and one 3/8” LOCK NUT (6) as shown in FIGURE 12.
13 FIGURE 14 STEP 14: • Carefully route the LEG PRESS CABLE (2) around one 3-1/2” PULLEY (4) and SECUREL Y assemble the 3-1/2” PULLEY (4) to the bracket on the SEA T FRAME using one 3/8 X 1-3/4” BOL T (7) and one 3/8” LOCK NUT (6) as shown in FIGURE 14.
FIGURE 15 STEP15: • Carefully route the SHOR T LEG PRESS CABLE (2) around one 3-1/2” PULLEY (4) and SECUREL Y assemble the 3-1/2” PULLEY (4) to the SEA T FRAME using one 3/8 X 4-1/2” BOL T (10), two 3/8” FLANGE SP ACERS (14), two 3/8 X 1” SP ACERS (13) and one 3/8” LOW HEIGHT LOCK NUT (12) as shown in FIGURE 15.
FIGURE 18 STEP 18: • Carefully route the SHOR T LEG PRESS CABLE (2) around one 3-1/2” PULLEY (4) and SECUREL Y assemble the 3-1/2” PULLEY (4) to the MAIN ARM using one 3/8 X 2-3/4” BOL T (8), two 3/8” FLANGE SP ACERS (14) and one 3/8” LOCK NUT (6) as shown in FIGURE 18.
FIGURE 19 STEP 19: 3/8 X 4-1/2” 10 2 12 13 SEA T FRAME 14 16 • SECUREL Y assemble the threaded end of the SHOR T LEG PRESS CABLE (2) to the SEA T FRAME using one 3/8 X 4-1/2” BOL T (10), two 3/8 X 1” SP ACERS (13), one previosly removed THREADED HOUSING , two 3/8” FLANGE SP ACERS (14) and one 3/8”LOW HEIGHT LOCK NUT (12).
FIGURE 20 STEP 20: • T o set the correct amount of tension in the cables, push the HEAD PLA TE down, insert the WEIGHT SELECT OR PIN and perform several repititions at the leg press station.This will relax the cable system and prevent the HEAD PLA TE from lifting up.
STEP 1: 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • If the SECOND ST ACK OPTION has not been assembled to the 880, refer to the SECOND ST ACK OPTION USER’S GUIDE.
STEP 2: FIGURE 2 19 • Route the LONG LEG PRESS CABLE (3) around the 3-1/2” PULLEY on the PULLEY PLA TES using one existing 3/8 X 1-3/4” BOL T and one existing 3/8” LOCK NUT .
20 STEP 3: FIGURE 3 • Remove the two 3/8” BOL TS, 3/8” W ASHERS and 3/8” LOCK NUTS from the ST ACK BASE as shown in FIGURE 3. ST ACK BASE • SECUREL Y assemble the LEG PRESS ADAPTER (1) to the ST ACK BASE using the previously removed 3/8” BOL TS, 3/8” W ASHERS and 3/8” LOCK NUTS as shown in FIGURE 3.
21 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 5 STEP 5: • Carefully route the LONG LEG PRESS CABLE (3) around one 3-1/2” PULLEY (4) and SECUREL Y assemble the 3-1/2” PULLEY (4) to the BRACKET (.
22 FIGURE 7 STEP 7: • Carefully route the LONG LEG PRESS CABLE (3) around one 3-1/2” PULLEY (4) and SECUREL Y assemble the 3-1/2” PULLEY (4) to the bracket on the SEA T FRAME using one 3/8 X 1-3/4” BOL T (7) and one 3/8” LOCK NUT (6) as shown in FIGURE 7.
FIGURE 8 STEP 8: • Carefully route the LONG LEG PRESS CABLE (3) around one 3-1/2” PULLEY (4) and SECUREL Y assemble the 3-1/2” PULLEY (4) to the SEA T FRAME using one 3/8 X 4-1/2” BOL T (10), two 3/8” FLANGE SP ACERS (14), two 3/8 X 1” SP ACERS (13) and one 3/8” LOW HEIGHT LOCK NUT (12) as shown in FIGURE 8.
FIGURE 1 1 STEP 1 1: • Carefully route the LONG LEG PRESS CABLE (3) around one 3-1/2” PULLEY (4) and SECUREL Y assemble the 3-1/2” PULLEY (4) to the MAIN ARM using one 3/8 X 2-3/4” BOL T (8), two 3/8” FLANGE SP ACERS (14) and one 3/8” LOCK NUT (6) as shown in FIGURE 1 1.
FIGURE 12 STEP 12: 3/8 X 4-1/2” 10 3 12 13 SEA T FRAME 14 25 • SECUREL Y assemble the threaded end of the LONG LEG PRESS CABLE (3) to the SEA T FRAME using one 3/8 X 4-1/2” BOL T (10), two 3/8 X 1” SP ACERS (13), one previosly removed THREADED HOUSING , two 3/8” FLANGE SP ACERS (14) and one 3/8”LOW HEIGHT LOCK NUT (12).
26 STEP 13: • T o set the correct amount of tension in the cables, push the HEAD PLA TE down, insert the WEIGHT SELECT OR PIN and perform several repititions at the leg press station.This will relax the cable system and prevent the HEAD PLA TE from lifting up.
デバイスParaBody 880の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
ParaBody 880をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはParaBody 880の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ParaBody 880の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ParaBody 880で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ParaBody 880を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はParaBody 880の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ParaBody 880に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちParaBody 880デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
