Paradyneメーカー5620 RTUの使用説明書/サービス説明書
ページ先へ移動 of 20
TM 1 Hotwire 5620 RTU Customer Premises Installation Instructions Document Number 5620-A2-GN10-30 December 1998 Before Y ou Begin The Hotwire 5620 RTU (Remote T ermination Unit) interoperates with the Hotwire 8510 DSL Card in the DSLAM (Digital Subscriber Line Access Multiplexer) system.
2 Package Checklist V erify that your package contains the following: - Model 5620 Remote T ermination Unit (RTU) - DSL interface cable with RJ1 1 connectors - Power cord with power transformer - T wo ferrite chokes What Does the Hotwire RADSL R TU Do? The Hotwire 5620 RTU is a component in the Hotwire DSL Access System.
3 98-16105 Punchdown Block or NID DSL Jack RTU Customer Premises (CP) DSL Ethernet Crossover Cable Ethernet Cable or Central Office (CO) Demarcation Point Local Loop CP POTS Splitter DSL – Digital S.
4 DSL Access without a POTS Splitter When the Hotwire 5620 RTU is installed without a POTS splitter , a second telephone wiring pair is needed for DSL access.
5 Installing the DSL Access Wiring The local loop terminates at the punchdown block or NID. Wiring must be connected from the customer premises side of the punchdown block or the NID to the DSL jack. T ypically , the punchdown block is installed in commercial locations and the NID is installed in residential locations.
6 3. Locate the DSL pair of T1/R1 connectors on the customer premises side of the NID or punchdown block. Attach the wiring that will be connected to the DSL jack. In the following example, a NID is used without a POTS splitter . It includes an existing POTS line and a second pair installed for DSL access.
97-15300a RJ11 W all Jack or 7 The Hotwire 5620 RTU connects to the local loop via wiring from the demarcation point to an RJ1 1 wall jack. The DSL twisted-pair wiring from the local loop terminates at a new or existing wall jack. It may be necessary to install a standard single RJ1 1 jack or replace a single jack with a double RJ1 1 wall jack.
8 Installing the Hotwire 5620 R TU Place the Hotwire 5620 RTU on a flat surface with clearance for the rear connectors. Procedur e 1. Use the supplied RJ1 1 6-pin interface cable for the DSL connection. Insert one end of the cable into the jack labeled DSL.
9 2. Use an 8-pin Ethernet cable for the Ethernet connection. Insert one end of the cable into the jack labeled ETHERNET . Use a straight-through cable and connect the other end to an Ethernet hub.
496-14952 97-15303c Ethernet Line PO WER ETHERNET DSL Hotwire RTU F errite Choke 10 3. Place the large ferrite choke on the Ethernet cable as closely as possible to the RTU. Pass the Ethernet cable through the ferrite choke twice, creating a loop as shown.
11 Optional R TU W all Placement The Hotwire 5620 RTU is designed for tabletop placement. The R TU can also be mounted on a wall. T o mount an RTU, you will need: - Three slotted-head #6 self-threadin.
12 R TU Hardwar e T emplate F ront (LEDs) 98-16171 5.43" 7.55" T o Bottom Hole.
13 Power -On When power is applied, the RTU performs self-diagnostics and the PWR LED is on. The self-diagnostics includes a power-on self-test. During the power-on self-test, all of the LEDs turn on for one second.
14 T roubleshooting LED Symptom Action All LEDs are on. The RTU may be in download mode. W ait ten minutes. If LEDs remain on after ten minutes and the RTU is not in download mode, the RTU is not functional. Contact the NSP . ALM LED remains on. The power-on self-test may have failed.
98-16055a 8-Pin Plug Ethernet Cable Pin #1 Pin #8 15 Cables & Connectors Use standard twisted-pair CA T3 or better cables. This section is reference information. The Ethernet interface connector uses an 8-pin, non-keyed modular plug. — T o connect the RTU to an Ethernet hub, use the straight-through connection.
98-15304-01 6-Pin RJ11 Plug DSL Cable Pin #1 Pin #6 16 The DSL interface connector uses a 6-pin, non-keyed modular plug. RJ1 1 6-Pin Connector Pin # Function 1 & 2 Not used 3 DSL Ring 4 DSL T ip 5 & 6 Not used Model 5620 R TU T echnical Specifications Item Specification * Height x Width x Depth 1.
17 Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. T o ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered.
18 Declaration of Conformity This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2 and 15 of the Federal Communications Commission’s Rules. This compliance information statement pertains to the following products: T rade Name: Hotwire Model Number: 5620-A2-200 This device complies with Part 15 of the FCC Rules.
19 Canada EMI W arnings ! W ARNING: T o Users of Digital Apparatus in Canada: This Class B digital apparatus meets all requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matérial brouilleur du Canada.
20 W arranty , Sales, and Service Information Contact your local sales representative, service representative, or distributor directly for any help needed.
デバイスParadyne 5620 RTUの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Paradyne 5620 RTUをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはParadyne 5620 RTUの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Paradyne 5620 RTUの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Paradyne 5620 RTUで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Paradyne 5620 RTUを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はParadyne 5620 RTUの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Paradyne 5620 RTUに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちParadyne 5620 RTUデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。