Paradyneメーカー9550 DS3の使用説明書/サービス説明書
ページ先へ移動 of 20
1 iMar c ® 9550 DS3 Pr obe Installation Instructions Document Number 9550 -A2-GN10-00 September 2005 Contents Softwar e and Firmware License Agreemen t .............. ................ ................. .. 2 Product Documentation Online ..............
2 Software and Firmwar e License Agreement The ter ms and conditions of this License Ag reement (the “Agreement”) wil l apply to the software and/or firmware (individually or collectively the “S.
3 b . ANY AND ALL IMPLIED WARRA NTIES , INCLUDING WITHOUT LIMIT A TION IMPLIED W ARRANTIES OF MERCHANT ABILITY , FITNESS FOR A P ARTICULAR PURPOSE AND NON-INFRINGEMENT .
4 Unpacking and Inspecting the Equipment HANDLING PRECA UTIONS FOR ST A TIC-SENSITIVE DEVIC ES This pr oduct is designed to pr otect sensitive components fr om damage due to electr ostatic discharge (ESD) d uring normal operation.
5 Installing in a Rack T wo types of mounting screws are provided. Use: #10-32 mounting screws f or rails with threaded screw holes #12-24 mounting screws and self-retaini ng nuts f or rails with unthreaded scre w holes Procedure T o insta ll the Probe in a rack: 1.
6 3. Inser t and tighten the screws in the top screw positions, then tighten the bottom screws . Connecting to P ower The Probe requires a 120 V AC , 60 Hz pow er source. Procedure T o con nect the 9550 DS3 Probe to power: 1. Connect a ground wire to the grounding screw on the front of the Probe.
7 3. Plug the sock et end of the power cord into the po wer receptacle on the back of the Probe. 4. Plug the power cab le into a 120 V AC , 60 Hz outlet.
8 Connecting the Subscriber P ort The Subscribe r por t connects to your DTE, such as a router . Procedure T o connect the Subscriber po r t: 1. If clearance at the front of the Probe is limited, attach r ight-angle BNC adapters to the ends of two BNC cables .
9 Connecting to the DS3 Network The Network por t connects to the packet netw ork . Procedure T o con nect the Network po r t: 1. If clearance at the front of the Probe is limited, attach r ight-angle BNC adapters to the ends of two BNC cables . 2. T ake the end of the receive cab l e and push it onto the NETWORK RX (Receiv e) connector .
10 7. If the cable length is longer than 100 fe et (30 meters), set the LBO on the T3 Network Interf ace Options configuration screen to Long. The default is Shor t.
11 Connecting the Modem Port The Probe suppor ts asynchro nous ter minal interface sessions ov er its integral modem. Procedure T o connect the Modem port: 1. Plug one end of an RJ11 telephone cable into the Modem por t. 2. Plug the other end of the cable into an RJ11 telephone jack.
12 Connecting the Console P ort The Console por t can be used to connect a VT1 00-compatible terminal or a PC with terminal emulati on softwa re, pro viding di rect access to the asyn chronous terminal interf ace. Procedure T o con nect the Console por t to a ter minal or PC: 1.
13 Using the Asynchronous T erminal Interface The Probe should operate using the defaul t (f actor y-set) configuration options, with ex ception to the changes specified in thes e installation instru ctions. Ref er to the f ollowing table f or hel p in navigating through the menus.
14 Menu Hierar ch y The Menu Hierarchy sho ws the organization of the Probe’s asynchronous terminal interf ace screens. S t a t u s System and T est Status Self-T est Re sults Last System Reset Heal.
15 Configuration System Class of Ser vice Definitions Monitored Protocol Definitions Ser vice Lev el V er ification General Network Ph ysical AT M VPI, VCI Records T3 User Ports Ph ysical AT M VPI, VC.
16 Sa ving Conf iguration Options Procedure T o save a configuration option chan ge: 1. Press Ctrl-a t o switch to the functi on ke ys area at the bottom of the screen. 2. Ty p e s or S (S av e) and press Enter . The Sav e Configuration T o menu appears.
17 EMI Notices United States – EMI Notice This equipment has been teste d and f ound to comply with the limits for a Class A digital de vice, pursuant to P ar t 15 of the FCC ru les. These limits are designed to provide reasonable protection against har mful interf erence when the equipment is operated in a commercial environment.
18 Important Safety Instructions 1. Read and follow all warning notices an d instructions mar ked on the product or included in the manual . 2. Slots and openings in the cabinet are provided for v en tilation. T o ensure reliable operation of the product and to protec t it from overheating, these slots and openings must not be block ed or cov ered.
19 W arranty , Sales, Service, and T raining Inf ormation Contact your local sales representative , ser vic e representati v e, or distributor directly f o r any help needed.
20 *9550-A2-GN10-00* *9550-A2-GN10-00*.
デバイスParadyne 9550 DS3の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Paradyne 9550 DS3をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはParadyne 9550 DS3の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Paradyne 9550 DS3の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Paradyne 9550 DS3で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Paradyne 9550 DS3を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はParadyne 9550 DS3の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Paradyne 9550 DS3に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちParadyne 9550 DS3デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。