ParadyneメーカーNortel Backbone Link Node Router 5030の使用説明書/サービス説明書
ページ先へ移動 of 12
TM 1 HotWire 5030 POTS Splitter Customer Premises Installation Instructions Document Number 5030-A2-GN10-10 October 1997 Before Y ou Begin V erify that: The local loop POTS service is connected to the POTS/DSL network at the punchdown block or network interface device (NID).
2 What Does the POTS Splitter Do? The POTS splitter and HotWire Remote T ermination Unit (R TU) are components in the RADSL Access System. This system provides high-speed Internet or corporate LAN access over traditional twisted-pair copper telephone wiring.
97-15247 POTS Splitter Housing 3 Mounting the POTS Splitter Housing The POTS splitter can be placed: H On the outside of the structure near the NID or punchdown block, or H Inside the building. When mounted outside, the POTS splitter must be installed at or above the height of the NID, and should be a minimum of three feet above ground.
97-15437-01 Lever Closure Screw 4 Preparing the POTS Splitter " Procedur e 1. Unscrew the closure screw and open the housing by pressing on the lever on the right above the closure screw . 2. Remove the rubber grommet at the base of the POTS splitter .
5 Installing the POTS Splitter Wiring The local loop ends at the punchdown block or NID. Wiring must be connected from the customer premises (CP) side of the punchdown block or NID to the DSL jack. T ypically , the punchdown block is installed in commercial locations and the NID is installed in residential locations.
6 DSL/POTS From Local Loop T e le phone N e twork I nte rfa ce D e vice (NID) Ground Ti p T1 (Green) Ring R1 (Red) 97- 15502 Existing POTS Wiring to T elephone Demarcation Point Customer Premises 3. Disconnect the POTS wiring to the telephone from the T1/R1 connectors on the customer premises side.
7 Reconnecting to the Local Loop " Procedur e 1. Feed new jumper wiring through the POTS splitter rubber grommet. Remove the insulation at the end of the wiring. 2. On the left side labeled LINE, attach red to terminal screw P1 and green to terminal screw P2.
97-15251 Lever Closure Screw 8 3. Locate the T1/R1 connectors on the customer premises side of the punchdown block or NID where the existing POTS wiring was removed in Step 3 on page 6. Attach the jumper pair from P1/P2 labeled LINE in the POTS splitter to the T1/R1 connectors.
9 DSL Access Wiring " Procedur e 1. Attach new wiring to the T1/R1 connectors that will go to the DSL jack from the punchdown block or NID. 2. T ighten the T1/R1 terminal screws with a flat-blade screwdriver .
10 5030 POTS Splitter T echnical Specifications Item Specification * Height x Width x Depth 6.65 ″ x 5.44 ″ x 2.25 ″ (16.89 cm x 13.82 cm x 5.72 cm) Weight 10.2 ounces (289.2 grams) Approvals FCC Part 68 Safety Certifications Refer to the equipment’s label for Registration Number .
11 Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. This product is intended to be connected to Listed/Certified telephone wiring with a minimum of 24 A WG (.5 mm) behind a Listed/Certified primary protector .
12 If the Model 5030 T elephone Line Filter causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible.
デバイスParadyne Nortel Backbone Link Node Router 5030の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Paradyne Nortel Backbone Link Node Router 5030をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはParadyne Nortel Backbone Link Node Router 5030の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Paradyne Nortel Backbone Link Node Router 5030の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Paradyne Nortel Backbone Link Node Router 5030で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Paradyne Nortel Backbone Link Node Router 5030を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はParadyne Nortel Backbone Link Node Router 5030の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Paradyne Nortel Backbone Link Node Router 5030に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちParadyne Nortel Backbone Link Node Router 5030デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
