Patton electronicメーカー2172の使用説明書/サービス説明書
ページ先へ移動 of 22
USER MANUAL MODEL 2172 CopperLINK™ High Speed Ethernet Extender s SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M2172-UM Doc# 03333U2-001 Rev .
2 CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 Compliance ................................................................................... 4 EMC Compliance:...............................
3 C.1 10/100Base-T Interface .............................................................. 20 RJ-45 .......................................................................................... 20 C.2 CopperLINK Interface ...............................
4 1.0 W ARRANTY INFORMATION P atton Electronics warrants all Model 2172 components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of the shipment.
5 tele vision reception, which can be determined by disconnecting the cables , tr y to correct the interference b y one or more of the f ollowing measures: moving the computing equipment aw ay from th.
6 1.5 SAFETY WHEN W ORKING WITH ELECTRICITY • This device contains no user serviceable parts. The equipment shall be returned to Patton Electronics for repairs, or repaired by qualified service personnel. • Mains Voltage: Ensure that the external power adapter is a listed Limited Power Source.
7 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or one year f or par ts and labor . If any questions or problems arise during installation or use of this product, contact P atton Electronics T echnical Suppor t at +1 (301) 975-1007.
8 Figure 1. T ypical application The pair of 2172 models work together to create a transparent e xtension between two peered Ethernet LANs. Figure 1 shows a typical point-to- point application. 3.0 INSTALLATION T o install the 2172 Ethernet Extender , do the follo wing: 1.
9 Figure 2. Model 2172 standalone rear panel 3.1 CONNECTING THE T WISTED-PAIR LINE INTERFACE The Model 2172 suppor ts communication between two peer Ethernet LAN sites ov er a distance of up to 6,000 ft (1.8 km) over 24 A WG (0.5 mm) twisted-pair wire.
10 19 (0.9mm) and 26 A WG (0.4mm). Leased circuits that run through signal equalization equipment are not acceptable . 2. The Model 2172 is equipped with either an RJ-45 or a terminal block interf ace jac k that can be used on the CopperLINK interface.
11 Figure 4. Model 2172 (T erminal Block) twisted pair line interface . 3.2 CONNECTING THE 10/100BASE-T ETHERNET INTERFACE The shielded RJ-45 por t labeled Ethernet is the A uto-MDIX10/100Base- T interf ace. This por t is designed to connect directly to a 10/100Base-T network.
12 3.3 CONNECTING POWER The Model 2172 does not hav e a power s witch, so it powers up as soon as it is plugged in. An e xternal AC or DC pow er supply is availab le separately . This connec- tion is made via the barrel jack on the rear panel of the Model 2172.
13 Figure 6. Removing protectiv e cover Figure 7 on page 13 shows the orientation of the DIP switches in the On and Off positions. Figure 7. DIP switch orientation Power Link Ethernet CopperLINK™ Hi.
14 4.2 CONFIGURING DIP SWITCH S2 DIP s witch S2 is where y ou configure the CopperLINK line rate, symmet- ric or asymmetr ic, Ethernet, and Ether net Shutdown. T able 1 summa- rizes def ault positions of DIP s witches S2-1 through S2-8. Detailed descriptions of each switch f ollow the table .
15 Switches S2-4, S2-5 and S2-6: Ethernet Configuration Use s witches S2-4, S2-5 and S2-6 to configure Ethernet settings. Switch S2-7: Ethernet Shutdown Use s witch S2-7 to enable or disab le Ethernet Shutdown. When Ethernet Shutdown is enab led, the 2172 will disable the Ether net interf ace when there is no CopperLINK link detected.
16 operating mode and Ethernet Shutdown mode configuration. The S2-8 switch does not aff ect the data rate. The data r ate will alwa ys follow the L configur ation. 5.0 OPERATION Once the Model 2172s are properly installed, they should operate trans- parently .
17 Figure 8. Model 2172 standalone unit front panel T able 8: F ront panel LED descr iption LED Description PWR Solid GREEN to indicate the unit is powered on. LINK Solid GREEN (ON) to indicate that the end-to-end CopperLINK link between the Model 2172s is estab- lished.
18 APPENDIX A SPECIFICATIONS A.1 LAN CONNECTION • Shielded RJ-45, 10/100Base-T , IEEE 802.3 Ether net • CopperLINK Connection: RJ-45 or T erminal Block A.2 T RANSMISSION LINE T wo-wire unconditioned twisted pair. A.3 COPPERLINK LINE RATE AND COPPERLINK DISTANCE • Line Rate: 50 Mbps, symmetric upstream/downstream.
19 APPENDIX B MODEL 2172 SERIES F ACTOR Y REPLACEMENT P AR TS AND ACCESSOR IES *Only required with optional UI power supply (08055DCUI) P atton Model # Description Base Models 2172/E CopperLINK Multi .
20 APPENDIX C MODEL 2172 SERIES INTERFACE PIN ASSIGNMENT C.1 10/100BASE-T INTERFACE RJ-45 • Pin 1: TX+ • Pin 2: TX- • Pin 3: RX+ • Pin 6: RX- • Pins 4, 5, 7, 8: no connection C.2 COPPERLINK INTERFACE RJ-45 • Pin 4: RING • Pin 5: TIP • Pins 1, 2, 3, 6, 7, 8: no connection T erminal Block Figure 1.
21 APPENDIX D DISTANCE CHAR T, BASED ON 24 A WG (0.5 MM) Note The actual distance and link performance ma y var y depending on the environment and type/gauge of wire used. Note DS = downstream, US = upstream Symm Line Rate Distance in feet (km) Throughput at Max Distance 50 Mbps 800 (0.
22 Cop yright © 2001, 2002, 2006 P atton Electronics Company All Rights Reser ved..
デバイスPatton electronic 2172の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Patton electronic 2172をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPatton electronic 2172の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Patton electronic 2172の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Patton electronic 2172で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Patton electronic 2172を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPatton electronic 2172の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Patton electronic 2172に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPatton electronic 2172デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。