Patton electronicメーカーNetLink-E1 2715の使用説明書/サービス説明書
ページ先へ移動 of 20
USER MANU AL MODEL 2715 NetLink-E1: E1/Fractional E1 NTU SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .patton.com Part# 07M2715-A Doc# 086051UA Revised 12/10/98 An ISO-9001 .
P A TTON MODEL 2715 T ABLE OF CONTENTS Section P age 1.0 General Inf or mation ...............................................................2 1.1 W arranty Statement 1.2 Radio and TV Interference 1.3 CE and T elecommunication Appro vals 1.4 Ser vice Information 2.
1.4 SER VICE INFORMA TION All warranty and non-w arranty repairs must be returned freight pre- paid and insured to P atton Electronics. All returns must hav e a Retur n Materials Authorization number on the outside of the shipping contain- er .
2.0 GENERAL INFORMA TION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warrant- ed f or One Y ear par ts and labor . If any questions arise during installa- tion or use of the unit, contact P atton Electronics T echnical Ser vices at (301) 975-1007.
Switch SW1: Line Coding Use Switch SW1 to control the Network Line Coding options. Set these options to be the same as the Line Coding given to y ou by y our Ser vice Provider . If you are using two Model 2715s together as short range modems, set both units to HDB3.
Switch SW2: CAS Multiframe The Channel Associated Signaling (CAS) multiframe uses Timeslot 16 (TS16) to send multiframe (MF) alignment data. In CAS MF , a multi- frame is defined as 16 frames , where a frame consists of 32 64kb/s timeslots, numbered 0 to 31.
NO TE: When the data rate is set to 2.048Mb/s, then the unit is f orced into G.703 mode, and it transmits user data on all 32 times- lots. There is no framing inf or mation; theref ore, the CAS MF (SW2)and CRC-4 (SW3) s witches are ignored. In all other rate settings, the unit emplo ys G.
3.2.1 Introduction to Main Men u After entering the password, y ou may access all of the system’ s functions and parameters. The Main Menu looks lik e this: HELPFUL HINTS 1. T o mak e a selection, key the highlighted letter that corre- sponds to a menu selection.
3.2.2 System Configuration The System Configuration menu looks lik e this: The System Configuration options are described below: Line Format: G.703 (def ault) Options: G.703, G.704 G.703: G.703 is unframed, 2.048Mb/s. In this case, the DTE rate is equal to the line rate at the network interf ace (NI).
Clocking : Network (def ault) Options: Network, Internal, External Network: This is the most commonly used setting when connect- ing to a carrier’ s network. In this mode, the unit recov ers the clock from the receiv ed signal and uses it to transmit data.
3.2.3 System Diagnostics The System Diagnostics/Statistics screen looks like this: NO TE: This screen is updated once per second. The System Diagnostics/Statistics options and functions are described below .
22 21 Remote Loop Idle (def ault) The Remote Digital Loopback (RDL) test chec ks the performance of both the local and remote Model 2715s, as well as the comm unica- tion link between them. Data from the local DTE is sent across the entire communication circuit and looped bac k to the local DTE.
23 24 Use this option to select the test pattern used to test the link. NI ST A TUS The Network interface (NI) status is sho wn in the middle of the Diagnostics/Statistics screen.
25 26 Loop Timeout The Loop Timeout setting can be set to one of the follo wing: 00:05 = five min utes 00:10 = ten minutes 00:15 = fifteen minutes 00:30 = thir ty minutes (def ault setting) 00:45 = f .
27 28 4.3 PO WER CONNECTION The Model 2715 off ers three ways to supply e xter nal power: A C power , DC po wer and interface po wer . 4.3.1 Using the A C Po wer Supply (100-240V AC) The Model 2715 uses a 5VDC , 2A universal input 100-240V AC , power supply (center pin is +5V).
29 30 LOS The Loss of Sync LED lights when the unit loses synchronization with the incoming sig- nal. This may happen when there is a fram- ing mismatch or a loss of signal. In unframed mode, the LOS LED monitors the status of the transmit cloc k. ALM The alarm LED indicates the presence of a AIS or RAI, or Out of F rame condition.
31 32 T o perf or m an RDL test, follo w these steps: 1. Activate RDL. This ma y be done in two wa ys: a. Enter Remote Loop from the System Diagnostics/Statistics menu and toggle the <Spacebar> until “TM” appears next to the Remote Loop option.
33 34 APPENDIX A P A TTON MODEL 2715 SPECIFICA TIONS Network Data Rate: 2.048 Mbps Network Connector: RJ-48C Nominal Impedance: 120 ohm (75 ohm av ailable when using P atton Model 460 Balun) DTE Interface: V .35 (DCE Or ientation) on Male M/34 Line Coding: Selectable AMI or HDB3 Line Framing: G.
35 36 APPENDIX C P A TTON MODEL 2715 F ACT OR Y REPLA CEMENT P ARTS AND A CCESSORIES P atton Model # Description 2715/CM/UI .....................V .35 to E1 Conv er ter (V .35 M/34 Male, UI) 10 - 09F ...........................6 Foot Control P ort Cable, 25 mm to DB9F 08055DCUI.
37 38 APPENDIX D (continued) P A TTON MODEL 2715 INTERF ACE PIN ASSIGNMENTS M/34 Connector , T erminal Interface Pin # Signal A GND (Ear th Ground/Shield) B SGND (Signal Ground) D CTS (DCE Source) E D.
デバイスPatton electronic NetLink-E1 2715の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Patton electronic NetLink-E1 2715をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPatton electronic NetLink-E1 2715の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Patton electronic NetLink-E1 2715の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Patton electronic NetLink-E1 2715で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Patton electronic NetLink-E1 2715を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPatton electronic NetLink-E1 2715の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Patton electronic NetLink-E1 2715に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPatton electronic NetLink-E1 2715デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。