Pelcoメーカー100 Seriesの使用説明書/サービス説明書
ページ先へ移動 of 16
100 Series Camclosure ® Integrated Camera System W ith LowLight ™ DSS T echnology C2460M-A (7/03) ® INST ALLA TION/OPERA TION.
2 C2460M-A (7/03) LIST OF ILLUSTRA TIONS Figure Page 1 Installation Directly to a Wall/Ceiling ....................................................................................... ... 5 2 Installation Directly to a Concrete Wall/Ceiling ...........
C2460M-A (7/03) 3 Heater elements could be hot! When camera power is on, use caution when adjusting the camera. CAUTION IMPORT ANT SAFEGUARDS AND WARNINGS 1. Installation and servicing should be done only by qualified service personnel and conform to all local codes.
4 C2460M-A (7/03) WELCOME Thank you for purchasing Pelco’ s Camclosure ® integrated camera system with LowLight ™ , DSS (digital slow shutter) technology . Y our new ICS100 Series surface mount dome system includes a high-resolution, low light, color camera with auto iris and varifocal lens.
C2460M-A (7/03) 5 INST ALL THE BACK BOX REMOVE THE LOWER DOME Loosen the tamper -resistant screws with the supplied 1/8-inch hollow screwdriver bit. Remove the lower dome and place it to the side.
6 C2460M-A (7/03) Figure 3. Installation on a 4S Electrical Box 8-32 X .750 FLAT HEAD SCREW (SUPPLIED) 8-32 X .375 PAN HEAD SCREW (SUPPLIED) WALL OR CEILING ADAPTER PLATE BASE 4S ELECTRICAL BOX Attach Directly to Concrete Wall/Ceiling Refer to Figure 2 for the following steps.
C2460M-A (7/03) 7 Mount to a Plaster Ring Refer to Figure 4 for the following steps. Installation instructions assume that the 4S electrical box and plaster ring were previously installed. 1. Pull video and power wires into the base. 2. Attach the base to the plaster ring.
8 C2460M-A (7/03) Figure 5. Terminal Block for Input Power CONNECT POWER WIRES Depending on the input voltage, connect either the 12 VDC or 24 V AC input power wires to the terminal block inside the base. Refer to Figure 5 for the location of the terminal block.
C2460M-A (7/03) 9 INST ALL THE CAMERA MODULE CHECK HEA TER JUMPER The Camclosure is equipped with a heater to defrost the dome. Some installations may not require this heater . If the unit will never be subjected to a frost temperature, you can disable the heater , saving power requirements.
10 C2460M-A (7/03) W all Mounting – The camera bracket tab points out of the enclosure and the top of the camera points up towards the tab. Ceiling Mounting – The camera bracket tab points out of the enclosure and the top of the camera is pointed in the opposite direction.
C2460M-A (7/03) 11 Figure 7. Default Switch Settings and Location of Camera Adjustments ZOOM/FOCUS 1. Select a field of view by turning the zoom adjustment ring. Refer to Figure 7. 2. T ighten the zoom locking screw . 3. Adjust the focus by moving the focus locking screw clockwise/counterclockwise.
12 C2460M-A (7/03) AGC (AUTOMA TIC GAIN CONTROL) AGC automatically adjusts the image to compensate for changes in light levels. ON (Default setting) – Enables the AGC mode.
C2460M-A (7/03) 13 Figure 8. Window Adjustment REINST ALL THE LOWER DOME AND TRIM RING 1. Domes with Liners (only) – Position the viewing window over the lens of the camera. a. Loosen the three Phillip screws located in the dome. b. Insert the blade of a standard screwdriver in one of the adjustment grooves.
14 C2460M-A (7/03) SPECIFICA TIONS BACKBOX Electrical Input V oltage: 12 VDC or 24 V AC, ±10%, auto-sensing Power Consumption: 13 watts or less V ideo Connector: BNC General Operating T emperature: -.
C2460M-A (7/03) 15 REVISION HISTORY Manual # Date Comments C2460M 4/03 Preliminary manual for beta testing. C2460M-A 7/03 Final version. ® Pelco, the Pelco logo, Spectra, Genex, Esprit, Camclosure, and Legacy are registered trademarks of Pelco. © Copyright 2003, Pelco.
World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.
デバイスPelco 100 Seriesの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco 100 Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco 100 Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco 100 Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco 100 Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco 100 Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco 100 Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco 100 Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco 100 Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。