PelcoメーカーC1666M-A (4/06) 3の使用説明書/サービス説明書
ページ先へ移動 of 20
INST ALLA TION TW3001AR Active Receiver Single Channel for UTP T ransmission C1666M-A (4/06).
.
C1666M-A (4/06) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings.
4 C1666M-A (4/06) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
C1666M-A (4/06) 5 Description The TW3001AR is a single-channel active receiver that can receive live video over unshielded twisted pair (UTP) cable. The adaptive technology in the TW3001AR automatically adjusts the low , medium and high frequency components of the video signal allowing for the best possible video transmission.
6 C1666M-A (4/06) PARTS OF THE RECEIVER Figure 1. TW3001AR Parts Rubber Feet (4): For placing unit on a fl at surface, such as a desk or shelf. Status LED: Lights red when there is no UTP video being received. Lights green when there is UTP video being received.
C1666M-A (4/06) 7 Installation Make sure all parts are present for the unit. 1 Universal power supply (Part #PS04-1502-0512G) 1 Wall clip 1 2-pin power connector 1 2-pin UTP connector MOUNTING The TW3001AR receiver is 3 rack units high and can be mounted into a fi ber rack, onto a wall using a fiber wall mount kit or into the supplied wall clip.
8 C1666M-A (4/06) USING A WALL CLIP To attach the TW3001AR receiver to a wall using the supplied wall clip, refer to Figure 2 and do the following: 1. Attach the wall clip to a wall using two screws (not supplied).
C1666M-A (4/06) 9 SETTING THE DIP SWITCHES Y ou can override the adaptive technology by manually adjusting switches 1-4 on the DIP Switch. The factory default switch positions are shown in Figure 3. Switches 1-4 are set to AUTO and Switch 5 is set to High Mode.
10 C1666M-A (4/06) APPLICATIONS Y ou can connect the TW3001AR active receiver to transmitters, such as the TW3001P passive trans- ceiver and the TW3001A T active transmitter , and to Pelco UTP cameras, such as the CC3710/CC3610 Series.
C1666M-A (4/06) 11 Figure 4 shows a TW3001AR connected to a UTP camclosure. Figure 4. TW3001AR Connected to a UTP Camclosure + - CAMCLOSURE TW3001AR UTP MONITOR 12 VDC OR 24 VAC POWER SUPPLY BLUE WIRE.
12 C1666M-A (4/06) Figure 5 shows a TW3001AR connected to a UTP fi xed camera. Figure 5. TW3001AR Connected to a UTP Fixed Camera + - TW3001AR FIXED CAMERA 8 PINS (4-/5+) MONITOR UTP PIN 5 + PIN 4 - .
C1666M-A (4/06) 13 Figure 6 shows a TW3001AR connected to a UTP Spectra dome for Coaxitron PTZ control. Figure 6. TW3001AR Connected to a Spectra Dome + - TW3001AR UTP VIDEO COAXITRON SPECTRA MONITOR .
14 C1666M-A (4/06) Figure 7 shows a TW3001AR connected to a TW3001P passive transceiver . The TW3001P then connects to a non-UTP fi xed camera. Figure 7.
C1666M-A (4/06) 15 Figure 8 shows a TW3001AR connected to a TW3032P passive transceiver . Figure 8. TW3001AR Connected to a 32-Channel Passive T ransceiver + - TW3001AR TW3032P MONITOR UTP 12 VDC OR 2.
16 C1666M-A (4/06) Figure 9 shows a TW3001AR connected to a TW3004P passive transceiver . The TW3004P then connects to a non-UTP fi xed camera. Figure 9.
C1666M-A (4/06) 17 Specifications ELECTRICAL Input Voltage 12 VDC or 24 VAC, 50-60Hz Power Consumption 2.5 watts Wire T ype Unshielded T wisted Pair (24 AWG maximum) Wire Category Cat3 or better DC L.
18 C1666M-A (4/06).
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.
デバイスPelco C1666M-A (4/06) 3の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco C1666M-A (4/06) 3をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco C1666M-A (4/06) 3の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco C1666M-A (4/06) 3の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco C1666M-A (4/06) 3で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco C1666M-A (4/06) 3を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco C1666M-A (4/06) 3の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco C1666M-A (4/06) 3に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco C1666M-A (4/06) 3デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。