PelcoメーカーC1988M-Bの使用説明書/サービス説明書
ページ先へ移動 of 12
® Installation/Operation CC3751H-2 DSP Color Camera C1988M-B (4/03) Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.pelco.
[ 2 ] Pelco Manual C1988M-B (4/03) Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should be done only by qualified service and installation personnel.
Pelco Manual C1988M-B (4/03) [ 3 ] CAMERA LA YOUT Figure 1. Camera Layout INST ALLA TION Lens Mounting The camera can use a fixed iris, manual iris, or auto iris lens. The camera is factory set for a CS-mount lens, but is easily adjusted for a C-mount lens.
[ 4 ] Pelco Manual C1988M-B (4/03) Figure 4. Power Supply Connections Camera Mounting Use a standard 1/4-20 screw (provided) with a maximum thread length of 3/8-inch (10 mm) for top or bot- tom camera mounting. The mount adapter may be fitted to the top or bottom of the camera.
Pelco Manual C1988M-B (4/03) [ 5 ] AC Operation Only - If you are wiring more than one camera to the same transformer, connect one side of the transformer to the same terminal on all cameras, and connect the other side of the transformer to the re- maining terminal on all cameras.
[ 6 ] Pelco Manual C1988M-B (4/03) LENS SETUP AND FOCUS PROCEDURES V ideo Drive Auto Iris Lens Set the lens mode selector switch to AIV . Switch the ESC OFF . Refer to the lens instructions and adjust the lens for the optimum picture (video output level of 1V peak-to-peak).
Pelco Manual C1988M-B (4/03) [ 7 ] Figure 5. Back Focus Adjustment BACK FOCUS ADJUSTMENT The back focus adjustment is located at the front of the camera and is accessible from either side of the case. To adjust the back focus: 1. Loosen the two back focus locking screws (one on each side).
[ 8 ] Pelco Manual C1988M-B (4/03) SWITCH SETTINGS Figure 6. DIP Switch Default Settings OFF OFF OFF AW1 AIV INT NOR OFF OFF OFF BLC OPT ESC AW2 AID LL SHP LC DS1 DS2 ON PHASE LEVEL + - H L 1 2 3 4 5 6 7 8 9 10 00152 BLC - Backlight Compensation OFF (Default setting) - Disables the BLC mode.
Pelco Manual C1988M-B (4/03) [ 9 ] OFF - Disables the DSS mode. 4 Fields of Integration Maximum - 1/15-second scene update rate. 16 Fields of Integration Maximum - 1/4-second scene update rate. 30 Fields of Integration Maximum (Default setting) - 1/2-second scene update rate.
[ 10 ] Pelco Manual C1988M-B (4/03) CAMERA SYNCHRONIZA TION (AC OPERA TION ONL Y) When using more than one camera power supply , a brief vertical roll may occur on the monitor when a camera view is switched. T o eliminate vertical roll, adjust the phase control by synchronizing, or line-lock- ing, the cameras to one another .
Pelco Manual C1988M-B (4/03) [ 11 ] SPECIFICA TIONS GENERAL CCD Sensor: 1/3-inch interline transfer Picture Elements: 768 (H) x 494 (V) Sensing Area: 6 mm diagonally Synchronization System: INT/AC line lock Horizontal Resolution: 480 TV lines Iris Control: Electronic/passive Minimum Illumination: 0.
[ 12 ] Pelco Manual C1988M-B (4/03) REVISION HISTOR Y Manual # Date Comments C1988M 5/02 Original version. C1988M-A 6/02 Revised the lens connector wiring chart.
デバイスPelco C1988M-Bの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco C1988M-Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco C1988M-Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco C1988M-Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco C1988M-Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco C1988M-Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco C1988M-Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco C1988M-Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco C1988M-Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。